Manuals / Brands / Household Appliance / Burner / Eclipse Combustion / Household Appliance / Burner

Eclipse Combustion 5600, VeriFlame Single Burner Monitoring System P ARAMETER D

1 42

Download 42 pages, 840.53 Kb

10 Eclipse Veri-Flame Instruction Manual 818-2/02

Specifications (continued)

PARAMETER DESCRIPTION

Approvals • No Purge & Purge Models:

Series 5602: UL listed, CSA certified, FM approved and IRI acceptable.

Series 5603: No approvals.

Series 5605: UL listed, FM approved and IRI acceptable.

• Modulating Models:

Series 5602: UL recognized (must be mounted in panel), CSA certified, FM

approved and IRI acceptable.

Series 5603: No approvals.

Shipping Weight • 1.4 kilograms (3 lbs.) for all Veri-Flame models.

• 0.9 kilograms (2 lbs.) for Models 5602-10 & 5602-10-1 bases.

• 1.2 kilograms (2.6 lbs.) for Model 5602-40 base.

Dimensions

76mm

(3") 133mm

(5-1/4") Square

102mm

(4") Square 13mm

(1/2")

5.5mm

(7/32") Dia.

Mounting

Holes (4)

Knockouts

(10) for

13mm (1/2"

Conduit

Veri-Flame Unit/All Models

Veri-Flame Bases/Purge & No Purge Models

Model Number 5602-10 Model Number 5602-10-1

102mm

(4") Square

124mm

(4-7/8")

38mm

(1-1/2")

127mm

(5")

Square

38mm

(1-1/2")

127mm

(5")

Square

19mm

(3/4")

(See chart below.)

UL Listed, Guide No. MCCZ, File MH12613

UL Recognized, Guide No. MCCZ2, File MH12613

CSA Certified, Class No. 2632 01, File 37456

FM Approved, Class No. 7610, Report 1Y2A4.AF

Approval Information

Contents

Main 2 C D ISCLAIMER L IABILITY W About this manual A S D C H OW TO GET About this manual Tab le of contents Function Summary DIP Switch Selection Table of Contents System Installation Sensor Installation T est Procedures Maintenance & T roubleshooting Remote Display Messages Appendix Introduction 1 8 Figure 1.1 P D Specifications This section gives a detailed overview of Veri-Flame specifications and dimensions. D P Specifications P ARAMETER D Dimensions Veri-Flame Unit/All Models Veri-Flame Bases/Purge & No Purge Models Dimensions (continued) Veri-Flame/Modulating Model with Base Model Number 5602-40 Remote Display Model Number 5602-DB Remote Display Model Number 5602-DBP DIP Switch Location DIP Switch Selection DIP Switch Access No Purge DIP Switch Settings Modulation & Purge DIP Switch Settings Page Function Summary S TANDARD Interlocks and Limit Switch Input (Terminal 7) Combustion Air Switch Input (Terminal 6) Main Fuel Valve Closed Switch (T erminal V) Low Fire Start Page High to Low Fire Purge Modulation Capability with High to Low Fire Position Switch Interlocks System Errors & Lockout Conditions (Continued) S L - & P O PTIONAL System Installation Interlocks and Limit Switch Input Combustion Air Switch Input Ignition Wiring Low Fire Input Remote Reset Main Valve Closed Switch High Purge Input Figure 5.1 No Purge and Purge Wiring Diagrams No Purge Models Purge Models Modulation Wiring Diagram Figure 5.2 6 7 8 A 10 11 12 13 Figure 5.3 Typical Connections For All Models Figure 5.4 n Purge and No Purge Bases Model Number 5602-40 2 J2J1 Figure 5.5 Sequence Diagrams Flame Rods Sensor Wiring Sensor Installation 6 n Scanners Scanner Sighting Considerations Flame Signal Strength Test Procedures 7 Minimum Pilot Test Pilot Flame Failure Test Main Flame Failure Test Spark Sighting Test Limits & Interlock Tests M Maintenance & Troubleshooting Yearly Checklist Monthly Checklist T PROBLEM POSSIBLE CAUSE SOLUTION LED S combination of LEDs which are lit on the front cover of each Veri-Flame model. No Purge Model Table 8.1 LED Status & Conditions for Veri-Flame No Purge Models Table 8.2 LED Status & Conditions for Veri-Flame Purge Models Purge Model Table 8.3 LED Status & Conditions for Veri-Flame Modulation Models Modulation Model Remote Display Messages Veri-Flame Operating Sequence POWER ON (see next page) Was internal safe start check successful? EXTERNAL INTERLOCK CHECKS Is flame signal present? BURNER START-UP Is voltage present at air flow switch within ten seconds? MODULATION MODELS PURGE MODELS YES NO Page Veri-Flame Operating Sequence (continued) BURNER SHUTDOWN Shutdown is started by opening the operating interlock circuit. Is voltage present at interlocks? Is main valve closed switch made?* Is voltage present at air flow switch? FOR PURGE & MODULATING Remote Display Diagnostic Messages (Listed Alphabetically) Page Remote Display Diagnostic Messages (continued) C F Appendix ILLUSTRATED PARTS L