Specifications, 2G4072-52 Ports | Enterasys Networks specs

A

Specifications

This appendix provides the following information:

For information about...	Refer to page...

2G4072-52 Specifications	A-1

Mini-GBIC Input/Output Specifications	A-2

Gigabit Ethernet Specifications	A-3

COM Port Pinout Assignments	A-6

Regulatory Compliance	A-3

Enterasys Networks reserves the right to change specifications at any time without notice.

2G4072-52 Specifications

Table A‐1 describes I/O ports, processors and memory, physical, and environmental specifications for the 2G4072‐52.

Table A-1 Specifications

ItemSpecification

2G4072-52 Ports

Ports 1 through 48	48, 10BASE-T/100BASE-TX compliant ports via RJ45
	connectors.

Mini-GBIC Ports	4 Mini-GBIC slots for mix-and-match 1000BASE-SX,
	SX+ and LX compliant Mini-GBICs. See page A-2for
	supported Mini-GBICs.

N Standalone Series Installation Guide A-1

Image 53

Enterasys Networks manual 2G4072-52 Specifications, 2G4072-52 Ports, Table A-1 Specifications ItemSpecification

Contents

Enterasys Matrix Page Page Federal Communications Commission FCC Notice Product SafetyIndustry Canada Notice Class a ITE Notice Clase A. Aviso de ITE Compatibilidad Electromágnetica EMC Electromagnetic Compatibility EMCElektro- magnetische Kompatibilität EMC Hazardous Substances Supplement to Product Instructions Bsmi EMC Statement Taiwan Vcci Notice Declaration of Conformity Safety Information Class 1 Laser Transceivers Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Index TroubleshootingAppendix a Specifications Tables Figures Xiv Important Notice PrefaceWho Should Use This Guide For Refer to Structure of This GuideRelated Documents This guide uses the following conventions Document Conventions Support@enterasys.com Getting Help Introduction 2G4072-52 Switch Configuration Using WebViewConnectivity Management Standards Compatibility Lanview Diagnostic LEDsSwitch Configuration Using CLI Commands Lanview Diagnostic LEDs Introduction Link Aggregation Network Requirements 100BASE-TX Network 10BASE-T Network1000BASE-SX/SX+/LX Network 1000BASE-T Network Unpacking the 2G4072-52 Installation Rack Mounting Contents of 2G4072-52 Attaching Rack-mount Ears to Enterasys Matrix N SA 2G4072-52 Connecting Power Connecting Power Connecting UTP Cables Connecting to the Network RX TX Crossover Four-Wire Cable RJ45 Pinouts Eight-Wire Crossover Cable RJ45 Pinouts Connecting Fiber-Optic Cables to Mini-GBICs 2G4072-52 2G4072-52 ÃÄÀ What Is Needed Connecting to the COM Port for Local ManagementConnecting to an IBM PC or Compatible Device Parameter Setting 12 Connecting an IBM PC or Compatible Connecting to a VT Series Terminal 13 Connecting a VT Series Terminal Connecting to a Modem 14 Connecting to a Modem VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Adapter Wiring and Signal AssignmentsCOM Port Adapter Wiring and Signal Diagram RJ45 Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the InstallationLog-In Using a Console Port Connection Completing the Installation 15 Matrix Startup Screen Example N7 Chassis Viewing the Receive and Transmit Activity TroubleshootingUsing Lanview Color State Recommended Action LED Alternating 67% on, 33% off Refer to the Enterasys Matrix N Standalone Series Troubleshooting Checklist Problem Possible Cause Recommended Action Overview of Shutdown ProcedureTroubleshooting Checklist Last Resort Shutdown Procedure Using Reset Button Recommended Shutdown Procedure Using Reset Button 2G4072-52 Specifications SpecificationsTable A-1 Specifications ItemSpecification 2G4072-52 Ports Table A-2 Mini-GBIC Input/Output Port Specifications Mini-GBIC Input/Output SpecificationsProcessors/Memory Physical MGBIC-LC03 Specifications 1000BASE-SX Gigabit Ethernet SpecificationsMGBIC-LC01 / MGBIC-MT01 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LX MGBIC-02 Specifications 1000BASE-T MGBIC-08 Specifications 1000BASE-ELXTable A-7 MGBIC-08 Optical Specifications Table A-9 MGBIC-02 Specifications COM Port Pinout Assignments Table A-3 COM Port Pin Assignments Signal Name Input/OutputRegulatory Compliance Table A-4 Compliance Standards Regulatory Compliance Mode Switch Bank Settings and Optional Installations Required Tools Setting the Mode Switches Figure B-1 Mode Switch Location Location of Dimm and Dram Simm Memory Modules Memory Locations and Replacement Procedures Removing the Dimm Dimm Replacement Procedure Figure B-4 Installing the Dimm Installing the Dimm Figure B-5 Removing Chassis Cover Removing the Dram Simm Figure B-6 Dram Simm Connector Location Installing the Dram Simm Figure B-7 Installing the Dram Simm Page Numerics Index Pinout assignments console port A-6