1000BASE-T Network | Enterasys Networks 6H303-48, 4G4282-49 instruction

1000BASE-T Network

1000BASE-T Network

The 4G4202‐72 and 4G4282‐49 support 10/100/1000 Mbps by means of fixed RJ45 front panel connectors. These connections support copper wire connections that can operate up to 1000 Mbps. The device at the other end of the twisted pair segment must meet IEEE 802.3‐2002 network requirements for the devices to operate at Gigabit speed.

Note: The fixed ports of each module support Category 5 UTP cabling with an impedance between 85 and 111 ohms for 100 and 1000 Mbps operation and can automatically sense the port speed of the other device and adjusts its speed accordingly.

Matrix DFE-Gold Series Installation Guide 2-3

Image 31

Enterasys Networks 6H303-48, 4G4282-49, 9034096-02 manual 1000BASE-T Network

Contents

Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Safety Information Class 1 Laser Transceivers Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Index TroubleshootingAppendix a Specifications Appendix B Mode Switch Bank Settings Optional Installations Figures Tables Who Should Use This Guide About This GuideImportant Notice Related Documents How to Use This GuideFor Refer to Following conventions are used in this guide Conventions Used in This Guide Conventions Used in This Guide Xvi About This Guide For information about Refer to Introduction DFE-Gold Modules and Interface Options Overview of DFE Series Capabilities 4G4282-49 4G4202-72 4G4202-72 and 4G4282-49 DFE-Gold Modules 7G-6MGBIC and 7G-6MGBIC-A Gigabit Ethernet Interface Modules Connectivity Switch Configuration Using WebViewManagement Standards Compatibility Switch Configuration Using CLI CommandsSecure Networks Policy Support Getting Help Lanview Diagnostic LEDs Link Aggregation Network Requirements 100BASE-TX Network 10BASE-T Network1000BASE-SX/LX/ELX Network 1000BASE-T Network 1000BASE-T Network Network Requirements Important Notice Installation Contents of DFE-Gold Module Carton Quantity Installing Optional Network Expansion ModulesUnpacking the DFE-Gold Module Removing the Coverplate Installing the Network Expansion Module Installing the Network Expansion Module Preparation Installing an Optional Mini-GBIC Mini-GBIC with MT-RJ Connector Installation Mini-GBIC with LC Connector Removing the Mini-GBIC N5 POE Module Placement and Rules Example 4 -6, D Example 1 -6, aExample 2 -6, B Example 3 -6, C Installing the DFE Module into a Chassis To install the module, refer to ‐1 and proceed as follows Installing Module into Matrix E7 or N7 Chassis Card guides Installing Module into Matrix N1, N3, or N5 Chassis Installing Module into N1, N3, or N5 Chassis only N3 shown Connecting to the Network Connecting UTP Cables DFE RX+ TX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting Fiber-Optic Cables to Mini-GBICs 13 Cable Connection to MT-RJ Fiber-Optic Connectors 14 Cable Connection to LC Fiber-Optic Connectors What Is Needed Connecting to COM Port for Local Management Parameter Setting Connecting to an IBM PC or Compatible Device 15 Connecting an IBM PC or Compatible Device Connecting to a VT Series Terminal 16 Connecting a VT Series Terminal Connecting to a Modem 17 Connecting to a Modem RJ45 DB25 Adapter Wiring and Signal AssignmentsCOM Port Adapter Wiring and Signal Diagram RJ45 VT Series Port Adapter Wiring and Signal Diagram Completing the Installation of a New System Completing the InstallationModem Port Adapter Wiring and Signal Diagram First-Time Log-In Using a Console Port Connection 18 Matrix DFE Startup Screen Example N7 Chassis Logging in with an Administratively-Configured User Account Using Lanview TroubleshootingAbout the Management Mgmt LED 4G4282-49 Viewing the Receive and Transmit Activity Color State Recommended Action LED Amber Alternating 67% on, 33% and off off. Indicates that a Refer to the Matrix DFE-Gold Series Configuration Troubleshooting Checklist Matrix DFE-Gold Series Configuration Guide for DFE-Gold Module Shutdown Procedure OFFLINE/RESET Switch Recommended Shutdown Procedure Using OFFLINE/RESET Switch Last Resort Shutdown Procedure Using OFFLINE/RESET Switch DFE-Gold Module Specifications SpecificationsTable A-1 Specifications Processors/Memory Ethernet Interface Module Specifications Table A-3 Mini-GBIC Input/Output Port Specifications Mini-GBIC Input/Output Specifications MGBIC-LC01 / MGBIC-MT01 Specifications 1000BASE-SX Gigabit Ethernet SpecificationsMGBIC-LC03 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELX MGBIC-LC09 Specifications 1000BASE-LXTable A-10 MGBIC-08 Optical Specifications Table A-12 MGBIC-02 Specifications MGBIC-02 Specifications 1000BASE-TTable A-11 MGBIC-08 Operating Range 1550 nm Regulatory Compliance COM Port Pinout AssignmentsTable A-14 Compliance Standards Regulatory Compliance Regulatory Compliance Specifications Setting the Mode Switches Mode Switch Bank Settings Optional InstallationsRequired Tools Figure B-1 Mode Switch Location on 4G4202-72 and 4G4282-49 Location of Dram Simm and Dimm Memory Modules Memory Locations and Replacement Procedures Removing the Dram Simm Dram Simm Replacement Procedure Figure B-5 Removing the Existing Dram Simm from 4G4282-49 Figure B-6 Installing the Dram Simm on 4G4282-49 Installing the Dram Simm on 4G4282-49 Removing the Dimm Dimm Replacement Procedure Figure B-8 Installing the Dimm on 4G4202-72 or 4G4282-49 Installing the Dimm on 4G4202-72 or 4G4282-49 Numerics Index Index-2