Installation | Enterasys Networks 9034096-02, 4G4282-49, 6H303-48

Installing an Optional Mini-GBIC

Installation

To install a Mini‐GBIC with an MT‐RJ connection, refer to Figure 3‐3. For an LC connection, refer to Figure 3‐4. For an RJ45 connection, refer to Figure 3‐5. Then proceed as described below.

Note: If the Mini-GBIC is one with an RJ45 connector such as an MGBIC-02 (Figure 3-5), the installation procedure is the same as described below. However, the Mini-GBIC has a wire handle to release it.

1.Hold the Mini‐GBIC with its top side facing up and its 7‐pin edge connector facing the port slot.

2.Carefully align the Mini‐GBIC with the port slot.

3.Push the Mini‐GBIC into the port slot until the Mini‐GBIC “clicks” and locks into place.

Figure 3-3 Mini-GBIC with MT-RJ Connector

6 5 4 3 2 1

Á

Ä

À

Å

A-6MGBIC -7G

1

3

Ã

Â

4

1	Mini-GBIC (MGBIC-MT01)	4	Port slot
2	Mini-GBIC,top side	5	Mini-GBIC,protective dust cover
3	7-Pin edge connector (insertion side)	6	Release tab

3-6 Installation

Image 38

Enterasys Networks 9034096-02, 4G4282-49, 6H303-48 manual Installation, Mini-GBIC with MT-RJ Connector

Contents

Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Safety Information Class 1 Laser Transceivers Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Appendix B Mode Switch Bank Settings Optional Installations TroubleshootingAppendix a Specifications Index Figures Tables Important Notice About This GuideWho Should Use This Guide For Refer to How to Use This GuideRelated Documents Conventions Used in This Guide Following conventions are used in this guide Conventions Used in This Guide Xvi About This Guide Introduction For information about Refer to Overview of DFE Series Capabilities DFE-Gold Modules and Interface Options 4G4202-72 4G4282-49 4G4202-72 and 4G4282-49 DFE-Gold Modules 7G-6MGBIC and 7G-6MGBIC-A Gigabit Ethernet Interface Modules Management Switch Configuration Using WebViewConnectivity Secure Networks Policy Support Switch Configuration Using CLI CommandsStandards Compatibility Lanview Diagnostic LEDs Getting Help Network Requirements Link Aggregation 1000BASE-SX/LX/ELX Network 10BASE-T Network100BASE-TX Network 1000BASE-T Network 1000BASE-T Network Network Requirements Installation Important Notice Unpacking the DFE-Gold Module Installing Optional Network Expansion ModulesContents of DFE-Gold Module Carton Quantity Installing the Network Expansion Module Removing the Coverplate Installing the Network Expansion Module Installing an Optional Mini-GBIC Preparation Installation Mini-GBIC with MT-RJ Connector Mini-GBIC with LC Connector Removing the Mini-GBIC Module Placement and Rules N5 POE Example 3 -6, C Example 1 -6, aExample 2 -6, B Example 4 -6, D Installing the DFE Module into a Chassis Installing Module into Matrix E7 or N7 Chassis To install the module, refer to ‐1 and proceed as follows Card guides Installing Module into Matrix N1, N3, or N5 Chassis Connecting to the Network Installing Module into N1, N3, or N5 Chassis only N3 shown Connecting UTP Cables DFE RX+ TX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting Fiber-Optic Cables to Mini-GBICs 13 Cable Connection to MT-RJ Fiber-Optic Connectors 14 Cable Connection to LC Fiber-Optic Connectors Connecting to COM Port for Local Management What Is Needed Connecting to an IBM PC or Compatible Device Parameter Setting Connecting to a VT Series Terminal 15 Connecting an IBM PC or Compatible Device Connecting to a Modem 16 Connecting a VT Series Terminal 17 Connecting to a Modem VT Series Port Adapter Wiring and Signal Diagram Adapter Wiring and Signal AssignmentsCOM Port Adapter Wiring and Signal Diagram RJ45 RJ45 DB25 Modem Port Adapter Wiring and Signal Diagram Completing the InstallationCompleting the Installation of a New System First-Time Log-In Using a Console Port Connection 18 Matrix DFE Startup Screen Example N7 Chassis Logging in with an Administratively-Configured User Account About the Management Mgmt LED TroubleshootingUsing Lanview Viewing the Receive and Transmit Activity 4G4282-49 LED Color State Recommended Action Amber Alternating 67% on, 33% and off off. Indicates that a Troubleshooting Checklist Refer to the Matrix DFE-Gold Series Configuration DFE-Gold Module Shutdown Procedure Matrix DFE-Gold Series Configuration Guide for Recommended Shutdown Procedure Using OFFLINE/RESET Switch OFFLINE/RESET Switch Last Resort Shutdown Procedure Using OFFLINE/RESET Switch Table A-1 Specifications SpecificationsDFE-Gold Module Specifications Ethernet Interface Module Specifications Processors/Memory Mini-GBIC Input/Output Specifications Table A-3 Mini-GBIC Input/Output Port Specifications MGBIC-LC03 Specifications 1000BASE-LX Gigabit Ethernet SpecificationsMGBIC-LC01 / MGBIC-MT01 Specifications 1000BASE-SX Table A-10 MGBIC-08 Optical Specifications MGBIC-LC09 Specifications 1000BASE-LXMGBIC-08 Specifications 1000BASE-ELX Table A-11 MGBIC-08 Operating Range 1550 nm MGBIC-02 Specifications 1000BASE-TTable A-12 MGBIC-02 Specifications Table A-14 Compliance Standards Regulatory Compliance COM Port Pinout AssignmentsRegulatory Compliance Regulatory Compliance Specifications Required Tools Mode Switch Bank Settings Optional InstallationsSetting the Mode Switches Figure B-1 Mode Switch Location on 4G4202-72 and 4G4282-49 Memory Locations and Replacement Procedures Location of Dram Simm and Dimm Memory Modules Dram Simm Replacement Procedure Removing the Dram Simm Figure B-5 Removing the Existing Dram Simm from 4G4282-49 Installing the Dram Simm on 4G4282-49 Figure B-6 Installing the Dram Simm on 4G4282-49 Dimm Replacement Procedure Removing the Dimm Installing the Dimm on 4G4202-72 or 4G4282-49 Figure B-8 Installing the Dimm on 4G4202-72 or 4G4282-49 Index Numerics Index-2