Enterasys Networks 4G4282-49, 6H303-48, 9034096-02 guide

Connecting to the Network

Figure 3-14 Cable Connection to LC Fiber-Optic Connectors

Ã

Á

Â

1	Ä
2	Ä
3
4
5
6
7G-6MGBIC-A
1
2
3
4
5	À
6

1	Installed Mini-GBIC LC connector	4	Receive LED (RX)
2	LC cable connector	5	Transmit LED (TX)

3Release tab

3.Plug the other end of the cable into the appropriate port on the other device. Some cables may be terminated at the other end with two separate connectors, one for each

3-22 Installation

Image 54

Enterasys Networks 4G4282-49, 6H303-48, 9034096-02 manual Cable Connection to LC Fiber-Optic Connectors

Contents

Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Safety Information Class 1 Laser Transceivers Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Appendix B Mode Switch Bank Settings Optional Installations TroubleshootingAppendix a Specifications Index Figures Tables About This Guide Who Should Use This GuideImportant Notice How to Use This Guide Related DocumentsFor Refer to Conventions Used in This Guide Following conventions are used in this guide Conventions Used in This Guide Xvi About This Guide Introduction For information about Refer to Overview of DFE Series Capabilities DFE-Gold Modules and Interface Options 4G4202-72 4G4282-49 4G4202-72 and 4G4282-49 DFE-Gold Modules 7G-6MGBIC and 7G-6MGBIC-A Gigabit Ethernet Interface Modules Switch Configuration Using WebView ConnectivityManagement Switch Configuration Using CLI Commands Standards CompatibilitySecure Networks Policy Support Lanview Diagnostic LEDs Getting Help Network Requirements Link Aggregation 10BASE-T Network 100BASE-TX Network1000BASE-SX/LX/ELX Network 1000BASE-T Network 1000BASE-T Network Network Requirements Installation Important Notice Installing Optional Network Expansion Modules Contents of DFE-Gold Module Carton QuantityUnpacking the DFE-Gold Module Installing the Network Expansion Module Removing the Coverplate Installing the Network Expansion Module Installing an Optional Mini-GBIC Preparation Installation Mini-GBIC with MT-RJ Connector Mini-GBIC with LC Connector Removing the Mini-GBIC Module Placement and Rules N5 POE Example 3 -6, C Example 1 -6, aExample 2 -6, B Example 4 -6, D Installing the DFE Module into a Chassis Installing Module into Matrix E7 or N7 Chassis To install the module, refer to ‐1 and proceed as follows Card guides Installing Module into Matrix N1, N3, or N5 Chassis Connecting to the Network Installing Module into N1, N3, or N5 Chassis only N3 shown Connecting UTP Cables DFE RX+ TX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting Fiber-Optic Cables to Mini-GBICs 13 Cable Connection to MT-RJ Fiber-Optic Connectors 14 Cable Connection to LC Fiber-Optic Connectors Connecting to COM Port for Local Management What Is Needed Connecting to an IBM PC or Compatible Device Parameter Setting Connecting to a VT Series Terminal 15 Connecting an IBM PC or Compatible Device Connecting to a Modem 16 Connecting a VT Series Terminal 17 Connecting to a Modem VT Series Port Adapter Wiring and Signal Diagram Adapter Wiring and Signal AssignmentsCOM Port Adapter Wiring and Signal Diagram RJ45 RJ45 DB25 Completing the Installation Completing the Installation of a New SystemModem Port Adapter Wiring and Signal Diagram First-Time Log-In Using a Console Port Connection 18 Matrix DFE Startup Screen Example N7 Chassis Logging in with an Administratively-Configured User Account Troubleshooting Using LanviewAbout the Management Mgmt LED Viewing the Receive and Transmit Activity 4G4282-49 LED Color State Recommended Action Amber Alternating 67% on, 33% and off off. Indicates that a Troubleshooting Checklist Refer to the Matrix DFE-Gold Series Configuration DFE-Gold Module Shutdown Procedure Matrix DFE-Gold Series Configuration Guide for Recommended Shutdown Procedure Using OFFLINE/RESET Switch OFFLINE/RESET Switch Last Resort Shutdown Procedure Using OFFLINE/RESET Switch Specifications DFE-Gold Module SpecificationsTable A-1 Specifications Ethernet Interface Module Specifications Processors/Memory Mini-GBIC Input/Output Specifications Table A-3 Mini-GBIC Input/Output Port Specifications Gigabit Ethernet Specifications MGBIC-LC01 / MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-LX MGBIC-LC09 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELXTable A-10 MGBIC-08 Optical Specifications MGBIC-02 Specifications 1000BASE-T Table A-12 MGBIC-02 SpecificationsTable A-11 MGBIC-08 Operating Range 1550 nm COM Port Pinout Assignments Regulatory ComplianceTable A-14 Compliance Standards Regulatory Compliance Regulatory Compliance Specifications Mode Switch Bank Settings Optional Installations Setting the Mode SwitchesRequired Tools Figure B-1 Mode Switch Location on 4G4202-72 and 4G4282-49 Memory Locations and Replacement Procedures Location of Dram Simm and Dimm Memory Modules Dram Simm Replacement Procedure Removing the Dram Simm Figure B-5 Removing the Existing Dram Simm from 4G4282-49 Installing the Dram Simm on 4G4282-49 Figure B-6 Installing the Dram Simm on 4G4282-49 Dimm Replacement Procedure Removing the Dimm Installing the Dimm on 4G4202-72 or 4G4282-49 Figure B-8 Installing the Dimm on 4G4202-72 or 4G4282-49 Index Numerics Index-2