ABxxxxxxxx | Epson 410 manual

Chapter 5

Printer Commands

))))))))))))))))))))))))))))))))))))))))))))

^A ^D COMMAND

22Change SW2: Software dip switch #2. Below is the ^AB sequence:

12345678

^ABxxxxxxxx

*******.)))),

******.)))),*

*****.)))),**

*****RRR Power-up Label Format

*****000=ALWAYS EPROM Format 1

*****001=ROM or Saved Format File 1

*****010=ROM or Saved Format File 2

*****011=ROM or Saved Format File 3

*****100=ROM or Saved Format File 4

*****101=ROM or Saved Format File 5

*****110=ROM or Saved Format File 6

*****111=ROM or Saved Format File 7

****.))))Q 1=Use Saved Format File, 0=Rom Format

***.)))))Q 1=Print Button Enable, 0=Disable **.))))))Q 1=Disable Button Use, 0=Enable *.)))))))Q 1=>RESTARTED< Response Enable,

0=Disable

.))))))))Q 1=Clear Text Enable, 0=Disable

Position:

1Clear Text Function: If enabled, all variable text strings will be erased when a ^D2<CR> is processed.

2>RESTARTED< Response: If the printer has been reset and this switch has been enabled, the printer will respond with to the first poll by sending the >RESTARTED< message. If additional enquiries are made the printer will respond normally. The >RESTARTED< message is only sent once after reset.

3Button Use: Set to 1, the printer will not allow button use, even for paper feed.

4Print Button: If this is 0, the button can be used for paper feed, but cannot be used to initiate label printing.

5Power-up Format Type: Defines the power-up label format. This parameter

determines whether to use a saved format file for the power-up label, or a ROM format (defined by positions 6, 7, and 8). The saved format file must be battery backed to use the saved format file feature. See Appendix C for configuration instructions and section 5.3.7 for saved format file information. Please consult your service organization if changes or additions to the fixed ROM formats are required.

6,7,8 Power-up Label Format: These switches decide which format to use at power- up.

))))))))))))))))))))))))))))))))))))))))))))

410 Operators Manual

39

Image 45

Epson 410 manual ABxxxxxxxx

Contents

Microcom Corporation Operators Manual Table of Contents Table of Contents Table of Contents List of Tables Introduction Operators Manual Features and Specifications BAR Codes RAM Physical Printer Variations Front View Operators Manual Batch Mode Normal ModeStatus Label Mode Basic Operation Serial Parameters 9600-N-8-1 PAPER-OUT Mode Status Light Light Mode Meaning Color Normal and TAG/TEAR Modes Loading Paper Clearing Label Misfeeds Diaphragm Removal PEEL-AND-DISPENSE Mode Cleaning Instructions Cable Pinout Communications Printer Cables PC Connection Serial Designing Labels Using LDS Ccopy Filename COM1 PC Connection ParallelCcopy Filename LPT1 Easycr Learning LDSMicrocom Makes Itcr Hellocr Designing Labels Using LDS Chapter Label Header LSX Label Size X Direction HFM Number of Fields in LayoutLSY Label Size Y Direction WEB WEB Size LCB Label Control Byte DPS MM/SEC Inches PER Second Minute AGD Number of Steps to Activate GAP Detector 615,153,,20,30,,70,4CR Sample Session with a Label Header TSN Text String Number Label FieldsXB X Beginning Coordinate YB Y Beginning Coordinate TCI Text Conversion Identifier CC Character Count CGN Character Generator Number CGNOCR-A UPC/EAN Left Justified Right JustifiedCentered Above Baseline CMY Character Multiplier Y Direction CMX Character Multiplier X Direction TSP Text Starting Position CLX Character Cell Length X DirectionCLY Character Cell Length Y Direction 100, 40, 4, 1,4CR Sample Session with a Label Field Special Printer Control Codes Printer Commands Printer Enquiries Sending D Printer Commands Command Software DIP Switches and Eeprom Commands Position ABxxxxxxxx ABxxxxxxxx Position Always ABxxxxxxxx Printing Commands CommandClear commands LSY AUTO-SIZING and Valid GAP CommandsGAP AGD Command Auto-Size Label D30 CR Hhmmss CR DD/MN/YR/W CR REAL-TIME Clock= SUN = MON European Date Formatcr US Date FormatcrClock Optioncr Disable increment and decrement Serial Number CommandsSingle Serial Number Status D85 Command Load label control byte LCB a specifies the number Label Header Commands Saving Format Files Commands Send Saved Format File to Serial Port a selects which oneUsage File #1 ESCFile #2 File #3 Label Presence Sensor Control Command Command Clears command Text Strings Commands Ship Fromcr Miscellaneous Printer Commands Enable 450 Emulation Disable AllEnable 1 Enable 460 Emulation Required for the Logo Option Logos Procedure for Using the PCX2410 Software Chapter Printer Commands Opening Parameters Format of Logo Files Chapter Printer Commands Designing with BAR Codes Rotationscr DegreescrHuman Readables Chapter Printer Commands UPC-A HR W/CHKSUMCR UPC-A HR W/O Chksumcr 01234567890CR Making Lines Thick LinesHalf Lines Reverse Video LOT NumbercrQtycr Label Support Rack CLOCK/BATTERY Backed RAM SocketLarge Paper Roll Supply Holder PCX2410 Software Cleaning KIT Wysiwyg Software PackagesParallel Conversion Boards Limited Warranty Appendix a Warranty and Repair Procedures Return Material Authorization RMA Procedure Appendix B Cleaning KIT & Accessories Battery Backed RAM with REAL-TIME Clock Appendix C Configuration GuideAddition Format Area Graphic Images Appendix D Installing the Label Support Rack Appendix E More Label Samples Default POWER-UP Label Fonts UPC-A HR W/CHKSUMCR UPC-A HR W/O Chksumcr 01234567890CR Multipliercr XY Multipliercr 1XYCR 2XYCR 4XYCR 8XYCR D3CR Linescr Offset of 100CR D3CR Offset of 0CR D3CR D57CR 620,441,,10,25,,,352CR 100,100,13,1,13CR D56CR D2CR Aiag Label Wheelcr Aacr Appendix F Sample Basic Program Disk Label MakerPrint Print Print Close System Appendix G Quick Reference Command Summary Not Used Column Epson emulation 2 inch Printer StatisticsPage Auto-Size Label Section Emulation Control Text Mode Control Section Clears Commands 86, 88 Peel-and-Dispense Mode Section Advance when idleTurn off peel-and-dispense mode Turn on peel-and dispense mode Index Chapter Printer Commands Printer Commands Chapter Operators Manual