Sgs | Extron electronic SGS 408 manual

Up to 8 Inputs

RGB 109xi

DVD Player

PC Computer

Projector

Preview	Program	SGS 408
Monitor	Monitor

Figure 2-5 — Typical SGS 408 application

Genlocking Video Inputs for Accu-RATE Frame Lock™

All video inputs to the SGS 408 should be genlocked for Accu-RATE Frame Lock to work properly. In the example below (figure 2-6), a DVD player must be attached to input #1 through a time base corrector for the proper sync signal during Accu-RATE Frame Locking. Any other genlocked input devices will then be correctly synced to input #1.

Preview

Monitor

Program

Monitor

Projector

SGS 408

DVD Player

Time Base

Corrector

RGB 109xi

Black Burst

Generator

PC Computer

Betacam	Video	Video
Tape Deck	Camera	Camera

Figure 2-6 — SGS 408 genlocking connections

SGS 408 Switcher • Installation

2-5

Image 15

Extron electronic SGS 408 manual Genlocking Video Inputs for Accu-RATE Frame Lock, Sgs

Contents

SGS Eight Input, High Resolution, Seamless Graphic Switcher Instrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen Deutsch SGS 408 Quick Start QS-1 Quick Start SGS Quick Start SGS 408, cont’d Button Right adjustment knobLeft adjustment knob Button Right adjustment knob Left adjustment knob Table of Contents Table of Contents, cont’d One About the SGS FeaturesSGS 408 Switcher Introduction Introductiontroduction, cont’d SGS 408 Switcher Introduction Introduction, cont’d Two SGS 408 Switcher Installation Installationstallation, cont’dRear Panel Connectors Installation Rack mounting Mounting the switcher Installation, cont’d CablingTabletop/desktop mounting SGS Genlocking Video Inputs for Accu-RATE Frame Lock Attaching an ECP Attaching an RCP Pin Signal Cable PinoutsXLR cable pinouts Making an RCP comm cable DVI cable pinouts Three SGS 408 Switcher Operation Operationeration, cont’dFront Panel Controls LCD default screen Default Screen Operation, cont’d Configuring the SGS Selecting the input configuration menu Selecting the input configuration Selecting the output sync format and polarity Selecting the output rate Rgbs Rgbhv Selecting a test pattern 12 Test patterns Changing the title settings 15 ECP control 18 Resetting the title box submenu controls Setting the program keylock Performing a reset Setting the LCD appearance 23 Performing a reset Using the Image Controls Centering an imageSizing an image Filtering an image Adjusting contrast and brightness Freezing an input Selecting an Input Available effects Using the Black buttonApplying a cut Applying other effects 32 Standard wipe transitions 35 Square wipe effects 37 ECP key title effect Setting up a new effect 38 Setting up the Dissolve effect 41 Setting up the S curtains effect Implementing an established effect 44 Setting up the Square wipe effect Implementing a title Using executive mode Optimizing the Image Four SGS-initiated messages SGS 408 Switcher Serial CommunicationSerialCommunicationunication, c t’d RS-232 Programmer’s Guide Using the command/response table SGS error responses Serial Communication, cont’d Command/response table Command Ascii Response Description Command Ascii Installing the software Control Software for WindowsAdvanced Instructions SGS 408 Control Program window Using the software Five If the image does not appear Troubleshootingubleshooting, cont’dIf the switcher does not respond to controls SGS 408 Switcher Troubleshooting AAppendix a SGS 408 Switcher Specifications Specificationsecifications, cont’d General Specifications, cont’d AppendixBB SGS 408 Switcher Reference Information Upgrades and RepairsInternal access Installing the DVI connector option Replacing the AC fuse Figure B-2 Installing the DVI connector option Reference Information, cont’d Installing a firmware update Figure B-4 Locating and replacing ICs Part Numbers Related part numbersExtron Part Part Number FCC Class a Notice Extron’s Warranty Extron Electronics, USA