Standard System Contents, Optional Equipment | Fluke 90100 instruction

General Information	1
Unpacking and Inspection

Standard System Contents

•Model 35360A TRACKER Display

•Model 35300A Detector

•15 m Detector to Display Interface Cable (37783-15)

•AC Line Cord

•Customization Software Kit (37827): Contains disk, cable, and adapters.

Optional Equipment

•System Carrying Case (37780): (16.50 in. x 17.75 in. x 8.75 in.).

Dimensions are 41.9 cm wide x 45.2 cm long x 22.2 cm deep Empty weight is 0.9 kg (2 lbs.).

•Cable (37783-30): 30 m Detector to Display Interface Cable

•Build-Up Kit (37825): Contains 10 pieces of 0.44 cm acrylic part number 37051-1. Kits containing other quantities of plates, plate materials, and plate thicknesses are available.

•Pegs and Retainer Kit (37825): Contains eight each, pegs and retainers for attach build-up plates to detector.

Customization Software Kit (37827)

OPTIONAL:

Pegs and Retainer Kit (37825)

OPTIONAL: Build-Up Kit (37825)

OPTIONAL:

System Carrying Case (37780)

Model 35300A Detector

Model 35360A TRACKER Display

15m Detector to Display Interface Cable

(37783-15)Model 90100 TRAKCER System Instruction Manual (37826)

Figure 1-3. Model 90100 TRACKER System Parts and Accessories

1-7

Image 11

Fluke 90100 manual Standard System Contents, Optional Equipment

Contents

Tracker System Model Fluke Biomedical Table of Contents Customization Maintenance and ServiceAppendix a Using Build-Up Theory of Operation Introduction General Information Model Features Manual Addenda Before You Start Safety PrecautionsSafety Terms Specifications Ion Chamber Factory Calibration Nominal Ion Chamber CharacteristicsMechanical Specifications Recommended Operation Conditions Electrometer / A-D Converter Measurements ModeDisplay Mode Model 35360A Tracker Display Environment High Performance Battery ChargerUnpacking and Inspection Interface Cable Detector to Display Optional Equipment Standard System Contents Blank Rear Panel Familiarization Operation Detector Input Powering the System Display. Be sure to use the correct end of the cable 3 RS-232 Computer Interface RJ-45 Style Positioning the Model 35300A Detector in the Beam Operation Positioning the Model 353300A Detector in the Beam Front Panel Controls Operation Instructions Units Select PowerReset Test/Detector Using the TEST/DETECTOR Button Powering Up the Model 35360A Tracker DisplayPowering Down the Model 35360A Tracker Display Test/Detector Screen 2 Ion Chamber Calibration Factors Using the Units Select Button Using the Gain Select Button Normal Mode Using the AIR Density Button Absolute Measurements Using the Measure Select Button Normal Mode Percent-of-Center Measurements Underranging and Overranging Conditions Battery and Bias Annunciators 24. Positions of the Battery and Bias Annunciators Gain Setting Mode Aborting the Fpgf Changes Saving the Fpgf Changes Blank Theory of Operation Hardware Block Diagram of the Model 35360A Tracker Display Power Supply VFD Display Front Panel Switches2 300-VOLT Electronic Bias Supply Processor Multiplexer and A/D Converter Serial Communications PortElectrometer Air Density Corrections Model 35300A Ion Chamber Detectors Basic Operating Equations Basic Operating Quantities Blank Maintenance & Service Problem Troubleshooting No Display Flowchart Low battery Yes Annuciator displayed? Low Battery Indication at the Display 35360A Tracker Bias Error LoBias or HiBias Indication at the Display Leakage Flowchart Dose Rate Measurement Zero Problem Flowchart Line Fuse Replacement If fuses continue to blow return instrument for repair Replaceable Parts Information Interface Connector CleaningCleaning the Instrument Recalibration & Repair Information / Technical Assistance Replaceable Parts List Customization Screen Formats Make a Working DiskConnection to the Computer Starting the Customization Software Display Customization Items Screen Appearance F10 Exit F1 Help On-Line Help for using the Customization softwareF2 Edit Item Editing F6 Print Report Printing Definitions Ion Chamber Calibration Factor Iccf Setting the Electrometer Gains and OffsetsCharge Gain QG Current Gain, Current Zero IG and ADZ Electrometer Charge Gains QG Electrometer Current Gain IG Usage Examples Changing the Power Down Interval Changing the ION Chamber Calibration Factor Units Input Errors Errors Build-Up, Peg, and Retainer Kit Options Using Build-Up Nominal Number of build-up Solid Water Appendix Fluke Biomedical