Manuals / Fluke / Baby / Child Tracker

Fluke 90100 manual Input Errors

Models: 90100

1 60

Download 60 pages 32.95 Kb

Page 56

Model 90100

Operators Manual

5.9 Errors

During program operations, errors may appear. The error messages are grouped into input errors, a hardware error, and communication errors.

INPUT ERRORS

Input errors may appear while changing Item values. When these errors occur, press any key to clear the error and enter a different value. After clearing the error, you may press Escape to end editing. The input errors are:

•Value must be greater than zero

•Must specify at least one digit

•Value must be less than 999.99

HARDWARE ERROR

A hardware error occurs when the program cannot perform a required hardware operation. The only hardware error is a printer error. If the Customization software cannot send information to the printer, the following message appears.

Printer Error

Press any key to clear the error. Correct the problem causing the error (for example, out of paper or the printer is not on-line), and try printing again.

COMMUNICATION ERRORS

These errors indicate that the communications between the computer and the instrument is faulty. Generally, the icon in the upper right corner indicates the status of the RS-232 connection. The following errors indicate problems during actual communication. Press any key to clear the error.

Dosimeter is not connected

If the RS-232 connection becomes severed during communication, this error appears. Re-connect the line and try the download again.

Upload/Download mismatch

If the information received from the 35360A does not match that sent by the Customization software, this error appears. Generally, the downloaded information was out of the boundary given for the specific Item. The Customization software retains the ORIGINAL text or value.

Finally, the Customization software checks the RS-232 connection at the beginning of the program. If it detects that no instrument is connected, the program ends and an error message occurs. Check the cable for breaks and confirm that the connections are solid. The program defaults to COM1: for the communications port. If that port is in use, specify COM2: by placing /2 on the command line:

custom /2

Also, make sure that the instrument has been on for at least five seconds.

5-10

Image 56

Fluke 90100 manual Input Errors

Contents

Model Tracker SystemFluke Biomedical Table of Contents Maintenance and Service Appendix a Using Build-UpTheory of Operation CustomizationGeneral Information IntroductionFeatures ModelBefore You Start Safety Precautions Safety TermsSpecifications Manual AddendaNominal Ion Chamber Characteristics Mechanical SpecificationsRecommended Operation Conditions Ion Chamber Factory CalibrationMeasurements Mode Display ModeModel 35360A Tracker Display Electrometer / A-D ConverterHigh Performance Battery Charger Unpacking and InspectionInterface Cable Detector to Display EnvironmentStandard System Contents Optional EquipmentBlank Operation Rear Panel FamiliarizationPowering the System Detector InputDisplay. Be sure to use the correct end of the cable Positioning the Model 35300A Detector in the Beam 3 RS-232 Computer Interface RJ-45 StyleOperation Positioning the Model 353300A Detector in the Beam Operation Instructions Front Panel ControlsPower ResetTest/Detector Units SelectUsing the TEST/DETECTOR Button Powering Up the Model 35360A Tracker DisplayPowering Down the Model 35360A Tracker Display Using the Units Select Button Test/Detector Screen 2 Ion Chamber Calibration FactorsUsing the AIR Density Button Using the Gain Select Button Normal ModeUsing the Measure Select Button Normal Mode Absolute MeasurementsPercent-of-Center Measurements Battery and Bias Annunciators Underranging and Overranging ConditionsGain Setting Mode 24. Positions of the Battery and Bias AnnunciatorsSaving the Fpgf Changes Aborting the Fpgf ChangesBlank Theory of Operation Power Supply Hardware Block Diagram of the Model 35360A Tracker DisplayFront Panel Switches 2 300-VOLT Electronic Bias SupplyProcessor VFD DisplayMultiplexer and A/D Converter Serial Communications PortElectrometer Model 35300A Ion Chamber Detectors Air Density CorrectionsBasic Operating Equations Basic Operating Quantities Blank Maintenance & Service Troubleshooting ProblemNo Display Flowchart Low Battery Indication at the Display Low battery Yes Annuciator displayed?Bias Error LoBias or HiBias Indication at the Display 35360A TrackerLeakage Flowchart Line Fuse Replacement Dose Rate Measurement Zero Problem FlowchartIf fuses continue to blow return instrument for repair Replaceable Parts Information Interface Connector CleaningCleaning the Instrument Replaceable Parts List Recalibration & Repair Information / Technical AssistanceCustomization Make a Working Disk Connection to the ComputerStarting the Customization Software Screen FormatsDisplay Customization Items Screen Appearance F1 Help On-Line Help for using the Customization software F2 Edit Item EditingF6 Print Report Printing F10 ExitDefinitions Setting the Electrometer Gains and Offsets Charge Gain QGCurrent Gain, Current Zero IG and ADZ Ion Chamber Calibration Factor IccfElectrometer Current Gain IG Electrometer Charge Gains QGChanging the Power Down Interval Usage ExamplesChanging the ION Chamber Calibration Factor Units Errors Input ErrorsUsing Build-Up Build-Up, Peg, and Retainer Kit OptionsNominal Number of build-up Solid Water Appendix Fluke Biomedical