Manuals / Fujitsu / Computer Equipment / Switch

Fujitsu MB88121 SERIES, MB91460 SERIES manual 5 Starter kit status after power on

Models: MB88121 SERIES MB91460 SERIES

1 73

Download 73 pages 7.7 Kb

Page 13

Image 13

SK-91F467-FLEXRAY V1.1

Installation

For the power supply of the SK-91F467-FLEXRAY a DC input voltage of 9V – 12V is recommended. The positive voltage (+) must be connected to the shield, and ground (GND) must be connected to the centre of the connector X5!

After power-on of the SK-91F467-FLEXRAY, the four red power-on LEDs D24 (5V), D30 (3.3V), D34 (2.5V) and D40 (1.8V) should be light. The reset LED D18 should be off.

Additionally the LED D2 and D4 should be on. The starter kit is delivered with programmed Softune Workbench Monitor Debugger in internal Flash of MB91F467D series. The monitor debugger is checking also the external SRAM access at CS1. In case of successful access to external SRAM the LED D2 and D4 are ON. In case of failed access LED D1 and D4 are set to ON.

Figure 2-5: Starter kit status after power on

- 13 -

FMEMCU-UG-910017-11

Page 13

Image 13

Fujitsu MB88121 SERIES, MB91460 SERIES manual 5 Starter kit status after power on

Contents

SK-91F467-FLEXRAY MB88121 SERIES MB91460 SERIESSTARTER KIT USER GUIDERevision History IssueDate FMEMCU-UG-910017-11NO LIABILITY FOR CONSEQUENTIAL DAMAGES Warranty and DisclaimerWARRANTY AND DISCLAIMER ContentsCONTENTS 2 INSTALLATION5 GETTING STARTED 4 CONNECTORS6 FLASH PROGRAMMING SK-91F467-FLEXRAY ContentsSILK-PLOT OF THE BOARD TROUBLE SHOOTINGPCB HISTORY 10 APPENDIX1.1 Abstract 1 IntroductionThis board must only be used for test applications 1.2 Featuresin an evaluation laboratory environment 1.3 General Description 1.3.6 External Bus interface Connectors 1.3.3 MCU Operating Mode1.3.1 On Board Memory 1.3.2 MCU Clocks1.3.13 Power Supply 1.3.10 MCU Pins1.3.11 User Buttons 1.3.12 User LEDs and optional LCDFigure 2-1 AC plug adapter 2 InstallationFigure 2-2 AC plug adapter selection Figure 2-3 DC voltage selectionFigure 2-5 Starter kit status after power on Default 2.1 Jumper SettingsJumper Description / FunctionDefault Table 2-1 Jumper settingsSchematic Jumper2.2 Jumper Location Figure 2-6 Default Jumper SettingsFigure 2-7 Softune Workbench start menu location 2.3 Software Installation 2.3.1 Installation of Softune WorkbenchFMEMCU-UG-910017-11 Figure 2-8 Softune Workbench V6 IDEFujitsu Microelectronics Europe GmbH DIP switch 3 Jumpers and SwitchesSetting Table 3-1 MCU Operating ModeFigure 3-2 FlexRay CC Mode Switch Table 3-2 FlexRay CC Operating Mode3.2 FlexRay CC Operating-Mode S2 1 2 3 4 5Table 3-3 FlexRay CC SPI Settings 3.3 FlexRay CC SPI Settings S1Figure 3-3 FlexRay CC SPI-Mode Switch DIP switchSwitch 3.4 Power SupplyTable 3-4 Power Switch Table 3-5 Power supply configurationsRegulator Figure 3-4 Voltage Test PointsTest point Voltage3.4.2 MCU Analogue Power Supply Voltage 3.4.1 MCU Power Supply VoltageTable 3-7 MCU Power Supply SK-91F467-FLEXRAY SettingTable 3-8 MCU ADC Supply 3.4.3 FlexRay CC Power Supply Voltage at SK-91F467-FLEXRAYTable 3-9 FlexRay CC Supply SettingSetting 3.5 MCU-FlexRay CC Connection at SK-91F467-FLEXRAYJumper Description3.6.1 Channel A 3.6 FlexRay Physical LayerTable 3-10 MCU-FlexRay CC Connection Setting3.6.2 Channel B Table 3-11 FlexRay CH-A ConfigurationSetting JumperSetting Table 3-12 FlexRay CH-B ConfigurationJumper DescriptionTable 3-13 FT1080 Control Settings 3.6.3 FT1080 Control Settings S6Figure 3-5 FT1080 Control Switch Table 3-14 FT1080 Connection to MCU3.8 LIN / RS-232 UART 3.7 CAN0 - CAN2Table 3-15 CAN-MCU connection Setting3.8.1 UART Table 3-16 UART2 SettingsSetting Jumper3.8.2 UART 4 Flash programming Table 3-17 UART4 SettingsSetting Jumper3.8.3 UART Table 3-18 UART5 SettingsSetting JumperTable 3-21 S3 Settings 3.10 User DIP Switch 8 Bit S43.9 User Push Buttons INT0, INT1, INT2 and ICU0/TIN0 Table 3-19 User Push ButtonsTable 3-22 Reset Connections 3.11 Reset GenerationTable 3-23 Supply Monitor Settings SettingSetting Table 3-24 Reset UART SelectionJumper Description4.1 Power Connector 4 Connectors4.2 UART / LIN Connector X1, X4 Figure 4-1 Power Connector4.4 FlexRay Connector X2 4.3 CAN Connector X9, X10Figure 4-3 CAN Connector Table 4-2 CAN Connector SignalsFigure 4-5 FlexRay Physical Layer Connector 4.5 FlexRay Physical Layer Module Connector X3Table 4-4 FlexRay Physical Layer Modules Pin Signal4.6 USER-LEDs and optional LC-Display D1-D16, J6 Table 4-5 LED/LCD SignalsFigure 4-6 User LEDs / LCD 4.8 MCU Pin Connectors J1-J4 4.7 In-Circuit-Programming ConnectorFigure 4-7 In Circuit Programming Connector Table 4-6 In-Circuit Programming ConnectorTable 4-8. VG96 X13 Signals 4.9 External Bus Connectors X13, X14 4.9.1 VG96ABC DIN 41612Fujitsu Microelectronics Europe GmbH FMEMCU-UG-910017-11Table 4-9 VG48 X14 Signals 4.9.3 Distance between VG-ConnectorsFigure 4-8 Layout of DIN VG Connectors 4.9.2 VG48ABC DIN 41612Figure 5-1 Softune Workbench main window 5.1 Introduction to Softune Workbench5 Getting Started 1 error detected in the compilation of Now Making Configuration Starterkit91302Test.prj - Debug main.cError detected C\SK-91F467-FLEXRAY\SK-91F467-FLEXRAYTest\Src\main.c5.2.1 Create a New Project 5.2 Project Start-up3. Enter the folder “myapplication” 4. Edit “myapplication.prj”Rename “91460template91467d” into “myapplication” Figure 5-2 Open Softune Workbench workspace *.wsp6. Start Softune Workbench and open your project FMEMCU-UG-910017-117 Select Active Configuration “MONDEBUG” 5.2.2 Use Active Configuration MONDEBUGINTERNALFigure 5-3 Project configuration selection Figure 5-5 Softune Workbench Linker Mapping Figure 5-4 Open Softune Workbench Linker mapping fileStart Softune Monitor Debugger via the “Debug” Command 5.2.3 Use Active configuration STANDALONEFigure 5-6 Start Softune Workbench Monitor Debugger STANDALONE5.3.1 General Description 5.3 Softune Workbench Monitor DebuggerFigure 5-7 MB91F467D and mode pin DIP switch U1, MCU MB91F467DA DIP switch S5, default all OFFFigure 5-8 Reset button and user LED Reset 8 User LEDsFigure 5-9 SWB debugging window 5.3.2 Basic Debugger Features Use the button INT0 on the “SK-91F467-xxx” for ABORT function 5.4 Advanced Monitor Debugger FeaturesExample Examplerestart set register PC=2000000 set break main Memory Map of Softune Workbench Monitor debugger 5.5 Memory Configuration for User ApplicationsMemory Type Used forCS1 - SRAM Checklist for project configuration0x0080.0000 - 0x009F.FFFF Memory Type6.1 Programming internal Flash of MB91F467DA series 6 Flash ProgrammingFigure 6-1 FME FR-Flash Programmer for MB91F467D series 5 Power-off the board or assert and hold RESET Figure 6-2 FME Flash Programmer output message window Table 7-1 Trouble shooting Trouble shootingProblem Solution8.1 Top Side 8 Silk-Plot of the BoardFigure 8-1 Board Layout Top Side Figure 8-2 Board Layout Bottom Side 8.2 Bottom SideFMEMCU-UG-910017-11 Fujitsu Microelectronics Europe GmbH9.1 SK-91F467-FLEXRAY 9 PCB History9.2 SK-91F467-FLEXRAY Table 9-1 History PCB10.1 Related Products 10 Appendixhttp//emea.fujitsu.com/microelectronics 10.2 Information on the WWW10.3 Tables Fujitsu Microelectronics Europe GmbH Table 7-1 Trouble shootingFMEMCU-UG-910017-11 Table 9-1 History PCB10.4 Figures 10.5 Abbreviations