Manuals / Fujitsu / Computer Equipment / Switch

Fujitsu MB88121 SERIES manual USER-LEDs and optional LC-Display D1-D16, J6, 5 LED/LCD Signals

Models: MB88121 SERIES MB91460 SERIES

1 73

Download 73 pages 7.7 Kb

Page 41

Image 41

SK-91F467-FLEXRAY V1.1

Connectors

4.6USER-LEDs and optional LC-Display (D1-D16, J6)

There are sixteen user LEDs on-board, D1-D8 connected to MCU port P25 and D9-D16 connected to MCU port P16. To disconnect the LEDs from the MCU, it is possible to remove RN3 (D1-D8 at port P25) and RN2 (D9-D16 at port P16).

It is also possible to connect a standard LCD module with backlight to connector J6. With the potentiometer RP1 the contrast of the LCD can be adjusted.

Pin	14	13	12	11	10	9	8	7	6	5	4	3	2	1	16	15
LCD	DB7	DB6	DB5	DB4	-	-	-	-	E	R/W	RS	VO	Vcc	GND	LED-	LED+
LED
LED	D8	D7	D6	D5				D4	D3	D2	D1
Port
Port	P25_7	P25_6	P25_5	P25_4				P25_3	P25_2	P25_1	P25_0
MCU
MCU	187	186	185	184				181	180	179	178

Table 4-5: LED/LCD Signals

LCD contrast

D16	D9	D8	D1
(Port: P16_7)	(Port: P16_0)	(Port: P25_7)	(Port: P25_0)

Figure 4-6: User LEDs / LCD

- 41 -

FMEMCU-UG-910017-11

Page 41

Image 41

Fujitsu MB88121 SERIES, MB91460 SERIES USER-LEDs and optional LC-Display D1-D16, J6, 5 LED/LCD Signals, 6 User LEDs / LCD

Contents

SK-91F467-FLEXRAY MB88121 SERIES MB91460 SERIESSTARTER KIT USER GUIDERevision History IssueDate FMEMCU-UG-910017-11NO LIABILITY FOR CONSEQUENTIAL DAMAGES Warranty and DisclaimerWARRANTY AND DISCLAIMER ContentsCONTENTS 2 INSTALLATION5 GETTING STARTED 4 CONNECTORS6 FLASH PROGRAMMING SK-91F467-FLEXRAY ContentsSILK-PLOT OF THE BOARD TROUBLE SHOOTINGPCB HISTORY 10 APPENDIX1.1 Abstract 1 Introductionin an evaluation laboratory environment 1.2 FeaturesThis board must only be used for test applications 1.3 General Description 1.3.6 External Bus interface Connectors 1.3.3 MCU Operating Mode1.3.1 On Board Memory 1.3.2 MCU Clocks1.3.13 Power Supply 1.3.10 MCU Pins1.3.11 User Buttons 1.3.12 User LEDs and optional LCDFigure 2-1 AC plug adapter 2 InstallationFigure 2-2 AC plug adapter selection Figure 2-3 DC voltage selectionFigure 2-5 Starter kit status after power on Default 2.1 Jumper SettingsJumper Description / FunctionDefault Table 2-1 Jumper settingsSchematic Jumper2.2 Jumper Location Figure 2-6 Default Jumper SettingsFigure 2-7 Softune Workbench start menu location 2.3 Software Installation 2.3.1 Installation of Softune WorkbenchFujitsu Microelectronics Europe GmbH Figure 2-8 Softune Workbench V6 IDEFMEMCU-UG-910017-11 DIP switch 3 Jumpers and SwitchesSetting Table 3-1 MCU Operating ModeFigure 3-2 FlexRay CC Mode Switch Table 3-2 FlexRay CC Operating Mode3.2 FlexRay CC Operating-Mode S2 1 2 3 4 5Table 3-3 FlexRay CC SPI Settings 3.3 FlexRay CC SPI Settings S1Figure 3-3 FlexRay CC SPI-Mode Switch DIP switchSwitch 3.4 Power SupplyTable 3-4 Power Switch Table 3-5 Power supply configurationsRegulator Figure 3-4 Voltage Test PointsTest point Voltage3.4.2 MCU Analogue Power Supply Voltage 3.4.1 MCU Power Supply VoltageTable 3-7 MCU Power Supply SK-91F467-FLEXRAY SettingTable 3-8 MCU ADC Supply 3.4.3 FlexRay CC Power Supply Voltage at SK-91F467-FLEXRAYTable 3-9 FlexRay CC Supply SettingSetting 3.5 MCU-FlexRay CC Connection at SK-91F467-FLEXRAYJumper Description3.6.1 Channel A 3.6 FlexRay Physical LayerTable 3-10 MCU-FlexRay CC Connection Setting3.6.2 Channel B Table 3-11 FlexRay CH-A ConfigurationSetting JumperSetting Table 3-12 FlexRay CH-B ConfigurationJumper DescriptionTable 3-13 FT1080 Control Settings 3.6.3 FT1080 Control Settings S6Figure 3-5 FT1080 Control Switch Table 3-14 FT1080 Connection to MCU3.8 LIN / RS-232 UART 3.7 CAN0 - CAN2Table 3-15 CAN-MCU connection Setting3.8.1 UART Table 3-16 UART2 SettingsSetting Jumper3.8.2 UART 4 Flash programming Table 3-17 UART4 SettingsSetting Jumper3.8.3 UART Table 3-18 UART5 SettingsSetting JumperTable 3-21 S3 Settings 3.10 User DIP Switch 8 Bit S43.9 User Push Buttons INT0, INT1, INT2 and ICU0/TIN0 Table 3-19 User Push ButtonsTable 3-22 Reset Connections 3.11 Reset GenerationTable 3-23 Supply Monitor Settings SettingSetting Table 3-24 Reset UART SelectionJumper Description4.1 Power Connector 4 Connectors4.2 UART / LIN Connector X1, X4 Figure 4-1 Power Connector4.4 FlexRay Connector X2 4.3 CAN Connector X9, X10Figure 4-3 CAN Connector Table 4-2 CAN Connector SignalsFigure 4-5 FlexRay Physical Layer Connector 4.5 FlexRay Physical Layer Module Connector X3Table 4-4 FlexRay Physical Layer Modules Pin SignalFigure 4-6 User LEDs / LCD Table 4-5 LED/LCD Signals4.6 USER-LEDs and optional LC-Display D1-D16, J6 4.8 MCU Pin Connectors J1-J4 4.7 In-Circuit-Programming ConnectorFigure 4-7 In Circuit Programming Connector Table 4-6 In-Circuit Programming ConnectorTable 4-8. VG96 X13 Signals 4.9 External Bus Connectors X13, X14 4.9.1 VG96ABC DIN 41612Fujitsu Microelectronics Europe GmbH FMEMCU-UG-910017-11Table 4-9 VG48 X14 Signals 4.9.3 Distance between VG-ConnectorsFigure 4-8 Layout of DIN VG Connectors 4.9.2 VG48ABC DIN 416125 Getting Started 5.1 Introduction to Softune WorkbenchFigure 5-1 Softune Workbench main window 1 error detected in the compilation of Now Making Configuration Starterkit91302Test.prj - Debug main.cError detected C\SK-91F467-FLEXRAY\SK-91F467-FLEXRAYTest\Src\main.c5.2.1 Create a New Project 5.2 Project Start-up3. Enter the folder “myapplication” 4. Edit “myapplication.prj”Rename “91460template91467d” into “myapplication” Figure 5-2 Open Softune Workbench workspace *.wsp6. Start Softune Workbench and open your project FMEMCU-UG-910017-11Figure 5-3 Project configuration selection 5.2.2 Use Active Configuration MONDEBUGINTERNAL7 Select Active Configuration “MONDEBUG” Figure 5-5 Softune Workbench Linker Mapping Figure 5-4 Open Softune Workbench Linker mapping fileStart Softune Monitor Debugger via the “Debug” Command 5.2.3 Use Active configuration STANDALONEFigure 5-6 Start Softune Workbench Monitor Debugger STANDALONE5.3.1 General Description 5.3 Softune Workbench Monitor DebuggerFigure 5-7 MB91F467D and mode pin DIP switch U1, MCU MB91F467DA DIP switch S5, default all OFFFigure 5-8 Reset button and user LED Reset 8 User LEDsFigure 5-9 SWB debugging window 5.3.2 Basic Debugger Features Use the button INT0 on the “SK-91F467-xxx” for ABORT function 5.4 Advanced Monitor Debugger FeaturesExample Examplerestart set register PC=2000000 set break main Memory Map of Softune Workbench Monitor debugger 5.5 Memory Configuration for User ApplicationsMemory Type Used forCS1 - SRAM Checklist for project configuration0x0080.0000 - 0x009F.FFFF Memory TypeFigure 6-1 FME FR-Flash Programmer for MB91F467D series 6 Flash Programming6.1 Programming internal Flash of MB91F467DA series 5 Power-off the board or assert and hold RESET Figure 6-2 FME Flash Programmer output message window Table 7-1 Trouble shooting Trouble shootingProblem SolutionFigure 8-1 Board Layout Top Side 8 Silk-Plot of the Board8.1 Top Side Figure 8-2 Board Layout Bottom Side 8.2 Bottom SideFMEMCU-UG-910017-11 Fujitsu Microelectronics Europe GmbH9.1 SK-91F467-FLEXRAY 9 PCB History9.2 SK-91F467-FLEXRAY Table 9-1 History PCB10.1 Related Products 10 Appendixhttp//emea.fujitsu.com/microelectronics 10.2 Information on the WWW10.3 Tables Fujitsu Microelectronics Europe GmbH Table 7-1 Trouble shootingFMEMCU-UG-910017-11 Table 9-1 History PCB10.4 Figures 10.5 Abbreviations