Manuals / Fujitsu / Computer Equipment / Switch

Fujitsu MB88121 SERIES FlexRay CC SPI Settings S1, 3 FlexRay CC SPI Settings, 1 2 3, DIP switch

Models: MB88121 SERIES MB91460 SERIES

1 73

Download 73 pages 7.7 Kb

Page 21

SK-91F467-FLEXRAY V1.1

Jumpers and Switches

3.3FlexRay CC SPI Settings (S1)

The DIP-switch S1 is used to set the FlexRay CC SPI settings, if the FlexRay CC is selected to communicate with the MCU over SPI. For more detailed information please check the Hardware-Manual of the FlexRay CC.

Note:

The DIP-switch (S1) is connected to the FlexRay CC in case the jumpers setting are set to SPI communication mode. Please refer to chapter 3.5 MCU-FlexRay CC Connection.

	DIP switch					Setting			Logical value
	DIP switch					Setting			Logical value
	S1/1 (MDS0)					ON (closed)			0 (low)
	S1/1 (MDS0)					OFF (open)			1 (high)
						OFF (open)			1 (high)
	S1/2 (MDS1)					ON (closed)			0 (low)
	S1/2 (MDS1)					OFF (open)			1 (high)
						OFF (open)			1 (high)
	S1/3 (MDS2)					ON (closed)			0 (low)
	S1/3 (MDS2)					OFF (open)			1 (high)
						OFF (open)			1 (high)
	S1/4 (Not used)					ON (closed)			Not connected
	S1/4 (Not used)					OFF (open)			Not connected
						OFF (open)			Not connected
	Default:
	Default:	grey

Table 3-3: FlexRay CC SPI Settings

The SPI function is not jet supported by MB88121!

Dip-Switch S1 (default setting)

MDS0 MDS1 MDS2 nc

ON

OFF

1 2 3 4

Figure 3-3: FlexRay CC SPI-Mode Switch

© Fujitsu Microelectronics Europe GmbH

- 21 -

FMEMCU-UG-910017-11

Image 21

Fujitsu MB88121 SERIES manual FlexRay CC SPI Settings S1, 3 FlexRay CC SPI Settings, 3 FlexRay CC SPI-Mode Switch, 1 2 3

Contents

SK-91F467-FLEXRAY MB88121 SERIES MB91460 SERIESSTARTER KIT USER GUIDERevision History IssueDate FMEMCU-UG-910017-11NO LIABILITY FOR CONSEQUENTIAL DAMAGES Warranty and DisclaimerWARRANTY AND DISCLAIMER ContentsCONTENTS 2 INSTALLATION5 GETTING STARTED 4 CONNECTORS6 FLASH PROGRAMMING SK-91F467-FLEXRAY ContentsSILK-PLOT OF THE BOARD TROUBLE SHOOTINGPCB HISTORY 10 APPENDIX1.1 Abstract 1 Introduction1.2 Features This board must only be used for test applicationsin an evaluation laboratory environment 1.3 General Description 1.3.6 External Bus interface Connectors 1.3.3 MCU Operating Mode1.3.1 On Board Memory 1.3.2 MCU Clocks1.3.13 Power Supply 1.3.10 MCU Pins1.3.11 User Buttons 1.3.12 User LEDs and optional LCDFigure 2-1 AC plug adapter 2 InstallationFigure 2-2 AC plug adapter selection Figure 2-3 DC voltage selectionFigure 2-5 Starter kit status after power on Default 2.1 Jumper SettingsJumper Description / FunctionDefault Table 2-1 Jumper settingsSchematic Jumper2.2 Jumper Location Figure 2-6 Default Jumper SettingsFigure 2-7 Softune Workbench start menu location 2.3 Software Installation 2.3.1 Installation of Softune WorkbenchFigure 2-8 Softune Workbench V6 IDE FMEMCU-UG-910017-11Fujitsu Microelectronics Europe GmbH DIP switch 3 Jumpers and SwitchesSetting Table 3-1 MCU Operating ModeFigure 3-2 FlexRay CC Mode Switch Table 3-2 FlexRay CC Operating Mode3.2 FlexRay CC Operating-Mode S2 1 2 3 4 5Table 3-3 FlexRay CC SPI Settings 3.3 FlexRay CC SPI Settings S1Figure 3-3 FlexRay CC SPI-Mode Switch DIP switchSwitch 3.4 Power SupplyTable 3-4 Power Switch Table 3-5 Power supply configurationsRegulator Figure 3-4 Voltage Test PointsTest point Voltage3.4.2 MCU Analogue Power Supply Voltage 3.4.1 MCU Power Supply VoltageTable 3-7 MCU Power Supply SK-91F467-FLEXRAY SettingTable 3-8 MCU ADC Supply 3.4.3 FlexRay CC Power Supply Voltage at SK-91F467-FLEXRAYTable 3-9 FlexRay CC Supply SettingSetting 3.5 MCU-FlexRay CC Connection at SK-91F467-FLEXRAYJumper Description3.6.1 Channel A 3.6 FlexRay Physical LayerTable 3-10 MCU-FlexRay CC Connection Setting3.6.2 Channel B Table 3-11 FlexRay CH-A ConfigurationSetting JumperSetting Table 3-12 FlexRay CH-B ConfigurationJumper DescriptionTable 3-13 FT1080 Control Settings 3.6.3 FT1080 Control Settings S6Figure 3-5 FT1080 Control Switch Table 3-14 FT1080 Connection to MCU3.8 LIN / RS-232 UART 3.7 CAN0 - CAN2Table 3-15 CAN-MCU connection Setting3.8.1 UART Table 3-16 UART2 SettingsSetting Jumper3.8.2 UART 4 Flash programming Table 3-17 UART4 SettingsSetting Jumper3.8.3 UART Table 3-18 UART5 SettingsSetting JumperTable 3-21 S3 Settings 3.10 User DIP Switch 8 Bit S43.9 User Push Buttons INT0, INT1, INT2 and ICU0/TIN0 Table 3-19 User Push ButtonsTable 3-22 Reset Connections 3.11 Reset GenerationTable 3-23 Supply Monitor Settings SettingSetting Table 3-24 Reset UART SelectionJumper Description4.1 Power Connector 4 Connectors4.2 UART / LIN Connector X1, X4 Figure 4-1 Power Connector4.4 FlexRay Connector X2 4.3 CAN Connector X9, X10Figure 4-3 CAN Connector Table 4-2 CAN Connector SignalsFigure 4-5 FlexRay Physical Layer Connector 4.5 FlexRay Physical Layer Module Connector X3Table 4-4 FlexRay Physical Layer Modules Pin SignalTable 4-5 LED/LCD Signals 4.6 USER-LEDs and optional LC-Display D1-D16, J6Figure 4-6 User LEDs / LCD 4.8 MCU Pin Connectors J1-J4 4.7 In-Circuit-Programming ConnectorFigure 4-7 In Circuit Programming Connector Table 4-6 In-Circuit Programming ConnectorTable 4-8. VG96 X13 Signals 4.9 External Bus Connectors X13, X14 4.9.1 VG96ABC DIN 41612Fujitsu Microelectronics Europe GmbH FMEMCU-UG-910017-11Table 4-9 VG48 X14 Signals 4.9.3 Distance between VG-ConnectorsFigure 4-8 Layout of DIN VG Connectors 4.9.2 VG48ABC DIN 416125.1 Introduction to Softune Workbench Figure 5-1 Softune Workbench main window5 Getting Started 1 error detected in the compilation of Now Making Configuration Starterkit91302Test.prj - Debug main.cError detected C\SK-91F467-FLEXRAY\SK-91F467-FLEXRAYTest\Src\main.c5.2.1 Create a New Project 5.2 Project Start-up3. Enter the folder “myapplication” 4. Edit “myapplication.prj”Rename “91460template91467d” into “myapplication” Figure 5-2 Open Softune Workbench workspace *.wsp6. Start Softune Workbench and open your project FMEMCU-UG-910017-115.2.2 Use Active Configuration MONDEBUGINTERNAL 7 Select Active Configuration “MONDEBUG”Figure 5-3 Project configuration selection Figure 5-5 Softune Workbench Linker Mapping Figure 5-4 Open Softune Workbench Linker mapping fileStart Softune Monitor Debugger via the “Debug” Command 5.2.3 Use Active configuration STANDALONEFigure 5-6 Start Softune Workbench Monitor Debugger STANDALONE5.3.1 General Description 5.3 Softune Workbench Monitor DebuggerFigure 5-7 MB91F467D and mode pin DIP switch U1, MCU MB91F467DA DIP switch S5, default all OFFFigure 5-8 Reset button and user LED Reset 8 User LEDsFigure 5-9 SWB debugging window 5.3.2 Basic Debugger Features Use the button INT0 on the “SK-91F467-xxx” for ABORT function 5.4 Advanced Monitor Debugger FeaturesExample Examplerestart set register PC=2000000 set break main Memory Map of Softune Workbench Monitor debugger 5.5 Memory Configuration for User ApplicationsMemory Type Used forCS1 - SRAM Checklist for project configuration0x0080.0000 - 0x009F.FFFF Memory Type6 Flash Programming 6.1 Programming internal Flash of MB91F467DA seriesFigure 6-1 FME FR-Flash Programmer for MB91F467D series 5 Power-off the board or assert and hold RESET Figure 6-2 FME Flash Programmer output message window Table 7-1 Trouble shooting Trouble shootingProblem Solution8 Silk-Plot of the Board 8.1 Top SideFigure 8-1 Board Layout Top Side Figure 8-2 Board Layout Bottom Side 8.2 Bottom SideFMEMCU-UG-910017-11 Fujitsu Microelectronics Europe GmbH9.1 SK-91F467-FLEXRAY 9 PCB History9.2 SK-91F467-FLEXRAY Table 9-1 History PCB10.1 Related Products 10 Appendixhttp//emea.fujitsu.com/microelectronics 10.2 Information on the WWW10.3 Tables Fujitsu Microelectronics Europe GmbH Table 7-1 Trouble shootingFMEMCU-UG-910017-11 Table 9-1 History PCB10.4 Figures 10.5 Abbreviations