Initialization, Initialized Settings | JL Audio MCS-3800 guide

Initialization

To clear the memory of the MCS-3800, and restore the Factory Preset settings, hold both the

UP and DOWN cursor buttons while powering up the unit.

Initialized Settings

From JLCooper, the MCS-3800 or MCS-3400's user-assignable memory is initialized to a “Factory Preset” set of (mainly) Controller messages on MIDI Channels 2 through 16.

The exceptions are the Transport switches, which are initialized to send MIDI Machine messages and (if option card is installed) Sony 9-pin messages.

The initialized values are as follows:

(MIDI Channel is shown in base 10, Controller # is in Hex)

Switch	MIDI Channel	Controller #
F1	16	00
Shifted F1	“	01
F2	“	02, etc.
Shifted F8	“	0F
W1	“	10
Shifted W1	“	11, etc.
Shifted W7	“	1D
M1	“	1E
Shifted M1	“	1F, etc.
Shifted M5	“	27

84

Image 84

JL Audio MCS-3800 manual Initialization, Initialized Settings, Switch Midi Channel Controller #

Contents

MCS-3000 Series Media Command Stations About this Manual Introduction Table of Contents Mixer Section Transport Section Warranty Quick Operation Reference 7 Page Summary Function Buttons SectionSystem Section Technical Information Getting Started Front Panel Displays and Controls Mixer Section Function Buttons Section Transport Section System Section Rear Panel Page Expander Connection Mounting MCS-3000X Expander to Controller Move Left End Bell 3000X Expander Electrical Hookup Set the Expander ID# Important Be Sure Each Expander has a Unique ID#Page Power System ConnectionsTime Code Midi In and Out Card Slots #1 and #2 OMS or Free Midi Definitions Power Up Entering and Exiting Assign ModeBasic Operation LCD and Page Buttons Modes of Operation More About User Assignable Mode More About Special Mode LED Behavior in Special Mode Manually Exiting Special Mode User Assignable vs. Pre-Defined Functionality Wave Demo This chapter relates to User Assignable Mode Only Mixer SectionAttributes of the Mixer Section Basic Bank Switching and Encoder Selection Encoder Selection Fader Output Fader Input Channel Switches Touch Sensor Encoders, Select Assigning Mixer Controls An Overview To Assign a Fader or a Touch Sensor Command Editable Parameters for the Faders and Touch Sensors NameNumber Channel Group GMaster To Assign the Rotary Encoders Editable Parameters for the Rotary Encoders Name To Assign Mute, Solo, Aux and Select Buttons Editable Parameters for Mute, Solo, Aux, and Select Name Minimum or Release Velocity Maximum or Velocity Latch Mixer Operation Notes Banks Remember Last Fader Position Touch Inhibits Motor Encoders Fader Groups Traverse Banks Group Members are Automatically Scaled Grand Masters Require Grand Master On Switch Grand Masters Traverse All Banks Moving Faders with Midi Data Created Off Line Page Transport Section Attributes of Transport Section Buttons Transports Jog Wheel and Shuttle Ring Locates Assigning Transport Controls To Assign a Transport or M Button Editable Parameters for Transport and M Buttons Name Transport and M Button Command Types Additional M Buttons Command Menu ItemsIf 9 Pin or GPI cards are present About Query Mode Maximum or Velocity Record Safety Feature M5 enables CS-10 EmulationTransport Operation Initialized State of Transports and M Buttons Example of Machine Enable Jog On / Off Feature Jog and Shuttle Operation Jog Controller Commands MMC and 9 Pin Commands JogShuttle Jog and Shuttle Speed Smpte Mode vs Feet and Frames Locate Operation Sending a Locate Command Storing a Locate by Capturing on the Fly More About Sending Locate Commands Locating by Direct AddressLast function Function Buttons Section Attributes of the Function Buttons Remote Control of the LEDs M Buttons Have More Than One PurposeCursor Buttons Have More Than One Purpose F and M Buttons have LEDs Assigning Function Buttons To Assign an F or M Button Editable Parameters for the Function Buttons F and M Name M Button Command Types About Query Mode Maximum or Velocity To Assign a W or Cursor Button Transport and M Button Commands Editable Parameters for Function Buttons Cursor & W Name Number Switch Grouping Function Button Operation Notes Entering Utility Mode Exiting Utility ModeSystem Section Mode Manually Exiting Special Mode ProtectDump Showtc Bank Name Jog Program Change Mode Program Change Mode Time Code Display Display Locates or Display Program Changes Dimensions Technical Information Initialized Settings Switch Midi Channel Controller #Initialization Switch Midi Chan Controller# Encoders Midi Chan Controller# Fader Midi Chan Controller # Touch Midi Chan Controller #Page Warranty Manually Switching Modes Quick Operation ReferenceFader Wave Demo Memory Initialization Bank Switchable Controls LCD Displays Encoder Names or Bank NameShiftable Controls To Assign a Control Command Types M Buttons Command Menu Also IncludesEditable Parameters Name If 9 Pin or GPI Cards are Present, M Commands Include Buttons Have Two UsesQuery More About Groups Jog Wheel and Shuttle Ring Locate Mode Time Code Display Entering and Exiting Utility Mode Offset Feet and Frame Ethernet Interface Card Installation and Configuration II. Initialization III. Operation