Mounting MCS-3000X Expander to Controller | JL Audio MCS-3800

Mounting MCS-3000X Expander to Controller

Important: Make All Connections with the Power Off. Turn the power off of all MCS-3000 units before proceeding.

Plan Work Area

You will want to work at a spacious, well lit surface. Spread a cloth on the surface to avoid scratching units.

Remove Top of MCS-3400 or MCS-3800 Controller Using the allen key provided with the Expander, remove the six top panel screws of the Controller. Remove any optional Cards from the card slots. Remove one screw under front center. Lift the whole top panel, a little forward and up. Invert and lay control-side down on a soft surface. (Circuit side up.)

Remove Top of MCS-3000X

Remove the six top panel screws of the Controller.

Lift top panel, a little forward and up. Invert and lay control- side down on a soft surface. (Circuit side up.)

Move Left End Bell

Remove the two screws that secure Controller's left end bell. (These screws will be tight). Attach the left end bell to the left side of the Expander.

Connect Controller to Expander with Plates Provided Place the Expander to the left of the Controller, side by side. Attach the thicker plate to the bottom of both units.

Lay thin (spring steel) plate on top of both units.

Replace top panels of the Controller, guiding in the Time Code jack and the LCD Contrast control into their holes. Replace the top panel of the Expander. Replace top screws. Replace Controller bottom screw. Replace any optional Cards in their card slots.

14

Image 14

JL Audio MCS-3800 manual Mounting MCS-3000X Expander to Controller, Move Left End Bell

Contents

MCS-3000 Series Media Command Stations About this Manual Introduction Table of Contents Mixer Section Transport Section System Section Warranty Quick Operation Reference 7 Page SummaryFunction Buttons Section Technical Information Getting Started Front Panel Displays and Controls Mixer Section Function Buttons Section Transport Section System Section Rear Panel Page Expander Connection Mounting MCS-3000X Expander to Controller Move Left End Bell 3000X Expander Electrical Hookup Set the Expander ID# Important Be Sure Each Expander has a Unique ID#Page Time Code PowerSystem Connections Midi In and Out Card Slots #1 and #2 OMS or Free Midi Definitions Basic Operation Power UpEntering and Exiting Assign Mode LCD and Page Buttons Modes of Operation More About User Assignable Mode More About Special Mode LED Behavior in Special Mode Manually Exiting Special Mode User Assignable vs. Pre-Defined Functionality Wave Demo Attributes of the Mixer Section This chapter relates to User Assignable Mode OnlyMixer Section Basic Bank Switching and Encoder Selection Encoder Selection Fader Output Fader Input Channel Switches Touch Sensor Encoders, Select Assigning Mixer Controls An Overview To Assign a Fader or a Touch Sensor Number CommandEditable Parameters for the Faders and Touch Sensors Name Channel Group GMaster To Assign the Rotary Encoders Editable Parameters for the Rotary Encoders Name To Assign Mute, Solo, Aux and Select Buttons Editable Parameters for Mute, Solo, Aux, and Select Name Minimum or Release Velocity Maximum or Velocity Latch Mixer Operation Notes Banks Remember Last Fader Position Touch Inhibits Motor Encoders Fader Groups Traverse Banks Group Members are Automatically Scaled Grand Masters Require Grand Master On Switch Grand Masters Traverse All Banks Moving Faders with Midi Data Created Off Line Page Transport Section Attributes of Transport Section Buttons Transports Jog Wheel and Shuttle Ring Locates Assigning Transport Controls To Assign a Transport or M Button Editable Parameters for Transport and M Buttons Name If 9 Pin or GPI cards are present Transport and M Button Command TypesAdditional M Buttons Command Menu Items About Query Mode Maximum or Velocity Transport Operation Record Safety FeatureM5 enables CS-10 Emulation Initialized State of Transports and M Buttons Example of Machine Enable Jog On / Off Feature Jog and Shuttle Operation Shuttle Jog Controller CommandsMMC and 9 Pin Commands Jog Jog and Shuttle Speed Smpte Mode vs Feet and Frames Locate Operation Sending a Locate Command Storing a Locate by Capturing on the Fly Last function More About Sending Locate CommandsLocating by Direct Address Function Buttons Section Attributes of the Function Buttons Cursor Buttons Have More Than One Purpose Remote Control of the LEDsM Buttons Have More Than One Purpose F and M Buttons have LEDs Assigning Function Buttons To Assign an F or M Button Editable Parameters for the Function Buttons F and M Name M Button Command Types About Query Mode Maximum or Velocity To Assign a W or Cursor Button Transport and M Button Commands Editable Parameters for Function Buttons Cursor & W Name Number Switch Grouping Function Button Operation Notes System Section Entering Utility ModeExiting Utility Mode Dump Mode Manually Exiting Special ModeProtect Showtc Bank Name Jog Program Change Mode Program Change Mode Time Code Display Display Locates or Display Program Changes Dimensions Technical Information Initialization Initialized SettingsSwitch Midi Channel Controller # Switch Midi Chan Controller# Encoders Midi Chan Controller# Fader Midi Chan Controller # Touch Midi Chan Controller #Page Warranty Fader Wave Demo Manually Switching ModesQuick Operation Reference Memory Initialization Shiftable Controls Bank Switchable ControlsLCD Displays Encoder Names or Bank Name To Assign a Control Editable Parameters Name Command TypesM Buttons Command Menu Also Includes Query If 9 Pin or GPI Cards are Present, M Commands IncludeButtons Have Two Uses More About Groups Jog Wheel and Shuttle Ring Locate Mode Time Code Display Entering and Exiting Utility Mode Offset Feet and Frame Ethernet Interface Card Installation and Configuration II. Initialization III. Operation