Transports, Jog Wheel and Shuttle Ring | JL Audio MCS-3800 guide

Transports

The Transports consist of Rewind, Fast Forward, Stop, Play, and Record. The i.d. number that they transmit can be made to be dependent upon the state of the M buttons. Refer to the previous page.

The LEDs behave “exclusively”, that is, pressing Play turns on the Play LED while turning off the Stop LED.

Record cannot be engaged unless Play is pressed and held down first.

Jog Wheel and Shuttle Ring

Jog and Shuttle transmit MIDI Machine Control and MIDI Controllers (CS-10 protocol), depending on the state of the M buttons. When the optional 9 pin card is installed, Jog and Shuttle can also send 9 Pin commands, for controlling professional VTRs.

The Shuttle Ring features a center detent, and direction LEDs.

The Speed of the Jog Wheel and the Shuttle Ring can be user- adjusted in the Utility Mode.

To enter Utility Mode, press Shift Assign. Turn the right-most encoder, and go to the page where you see "Jog" and 'Shuttle".

The Jog Speed range is 1 through 100.

Shuttle Speed range is 1X through 32X.

That is, when the Shuttle Ring is rotated as far as its goes, the machine will play up to 32 time Play Speed.

Any Transport or Function button can be made into a master "On / Off" control for the Jog / Shuttle mechanism.

49

Image 49

JL Audio MCS-3800 manual Transports, Jog Wheel and Shuttle Ring

Contents

MCS-3000 Series Media Command Stations About this Manual Introduction Table of Contents Transport Section Mixer Section Function Buttons Section Warranty Quick Operation Reference 7 Page SummarySystem Section Technical Information Front Panel Displays and Controls Getting Started Function Buttons Section Mixer Section Transport Section System Section Rear Panel Page Expander Connection Move Left End Bell Mounting MCS-3000X Expander to Controller 3000X Expander Electrical Hookup Important Be Sure Each Expander has a Unique ID# Set the Expander ID#Page System Connections PowerTime Code Card Slots #1 and #2 Midi In and Out OMS or Free Midi Definitions Entering and Exiting Assign Mode Power UpBasic Operation Modes of Operation LCD and Page Buttons More About Special Mode More About User Assignable Mode LED Behavior in Special Mode User Assignable vs. Pre-Defined Functionality Manually Exiting Special Mode Wave Demo Mixer Section This chapter relates to User Assignable Mode OnlyAttributes of the Mixer Section Encoder Selection Basic Bank Switching and Encoder Selection Fader Input Fader Output Touch Sensor Channel Switches Encoders, Select An Overview Assigning Mixer Controls To Assign a Fader or a Touch Sensor Editable Parameters for the Faders and Touch Sensors Name CommandNumber Channel GMaster Group To Assign the Rotary Encoders Editable Parameters for the Rotary Encoders Name To Assign Mute, Solo, Aux and Select Buttons Minimum or Release Velocity Editable Parameters for Mute, Solo, Aux, and Select Name Latch Maximum or Velocity Touch Inhibits Motor Mixer Operation Notes Banks Remember Last Fader Position Encoders Group Members are Automatically Scaled Fader Groups Traverse Banks Grand Masters Traverse All Banks Grand Masters Require Grand Master On Switch Moving Faders with Midi Data Created Off Line Page Attributes of Transport Section Transport Section Buttons Jog Wheel and Shuttle Ring Transports Locates Assigning Transport Controls To Assign a Transport or M Button Editable Parameters for Transport and M Buttons Name Additional M Buttons Command Menu Items Transport and M Button Command TypesIf 9 Pin or GPI cards are present About Query Mode Maximum or Velocity M5 enables CS-10 Emulation Record Safety FeatureTransport Operation Initialized State of Transports and M Buttons Example of Machine Enable Jog and Shuttle Operation Jog On / Off Feature MMC and 9 Pin Commands Jog Jog Controller CommandsShuttle Jog and Shuttle Speed Locate Operation Smpte Mode vs Feet and Frames Storing a Locate by Capturing on the Fly Sending a Locate Command Locating by Direct Address More About Sending Locate CommandsLast function Attributes of the Function Buttons Function Buttons Section M Buttons Have More Than One Purpose Remote Control of the LEDsCursor Buttons Have More Than One Purpose F and M Buttons have LEDs Assigning Function Buttons To Assign an F or M Button Editable Parameters for the Function Buttons F and M Name M Button Command Types About Query Mode Maximum or Velocity To Assign a W or Cursor Button Editable Parameters for Function Buttons Cursor & W Name Transport and M Button Commands Number Function Button Operation Notes Switch Grouping Exiting Utility Mode Entering Utility ModeSystem Section Protect Mode Manually Exiting Special ModeDump Bank Name Showtc Jog Program Change Mode Program Change Mode Display Locates or Display Program Changes Time Code Display Technical Information Dimensions Switch Midi Channel Controller # Initialized SettingsInitialization Switch Midi Chan Controller# Encoders Midi Chan Controller# Touch Midi Chan Controller # Fader Midi Chan Controller #Page Warranty Quick Operation Reference Manually Switching ModesFader Wave Demo Memory Initialization LCD Displays Encoder Names or Bank Name Bank Switchable ControlsShiftable Controls To Assign a Control M Buttons Command Menu Also Includes Command TypesEditable Parameters Name Buttons Have Two Uses If 9 Pin or GPI Cards are Present, M Commands IncludeQuery Jog Wheel and Shuttle Ring More About Groups Time Code Display Locate Mode Offset Feet and Frame Entering and Exiting Utility Mode Ethernet Interface Card Installation and Configuration II. Initialization III. Operation