Rear Panel | JL Audio MCS-3800 instruction

Rear Panel

MCS-3800 is shown, the MCS-3400 is similar.

From left to right we have:

•MIDI In, MIDI Out

•LCD Contrast Control

•MCS-3000X Expander Connector

•Time Code Input

The input jack is 1/4”, unbalanced, that is, tip & sleeve.

• Card Slot #1 and Card Slot #2

Accepts optional, user installable plug in cards for additional control.

• Power Jack

This supply is 12 Volts DC, at least 3A.

The strain relief clip adjacent to the jack may be used to loop the power cord through to prevent accidental unplugging.

• Power Switch

Flip up (red showing) to turn power on.

11

Image 11

JL Audio MCS-3800 manual Rear Panel

Contents

MCS-3000 Series Media Command Stations About this Manual Introduction Table of Contents Transport Section Mixer Section Technical Information Warranty Quick Operation Reference 7 Page SummaryFunction Buttons Section System Section Front Panel Displays and Controls Getting Started Function Buttons Section Mixer Section Transport Section System Section Rear Panel Page Expander Connection Move Left End Bell Mounting MCS-3000X Expander to Controller 3000X Expander Electrical Hookup Important Be Sure Each Expander has a Unique ID# Set the Expander ID#Page Time Code PowerSystem Connections Card Slots #1 and #2 Midi In and Out OMS or Free Midi Definitions Basic Operation Power UpEntering and Exiting Assign Mode Modes of Operation LCD and Page Buttons More About Special Mode More About User Assignable Mode LED Behavior in Special Mode User Assignable vs. Pre-Defined Functionality Manually Exiting Special Mode Wave Demo Attributes of the Mixer Section This chapter relates to User Assignable Mode OnlyMixer Section Encoder Selection Basic Bank Switching and Encoder Selection Fader Input Fader Output Touch Sensor Channel Switches Encoders, Select An Overview Assigning Mixer Controls To Assign a Fader or a Touch Sensor Channel CommandEditable Parameters for the Faders and Touch Sensors Name Number GMaster Group To Assign the Rotary Encoders Editable Parameters for the Rotary Encoders Name To Assign Mute, Solo, Aux and Select Buttons Minimum or Release Velocity Editable Parameters for Mute, Solo, Aux, and Select Name Latch Maximum or Velocity Touch Inhibits Motor Mixer Operation Notes Banks Remember Last Fader Position Encoders Group Members are Automatically Scaled Fader Groups Traverse Banks Grand Masters Traverse All Banks Grand Masters Require Grand Master On Switch Moving Faders with Midi Data Created Off Line Page Attributes of Transport Section Transport Section Buttons Jog Wheel and Shuttle Ring Transports Locates Assigning Transport Controls To Assign a Transport or M Button Editable Parameters for Transport and M Buttons Name If 9 Pin or GPI cards are present Transport and M Button Command TypesAdditional M Buttons Command Menu Items About Query Mode Maximum or Velocity Initialized State of Transports and M Buttons Record Safety FeatureM5 enables CS-10 Emulation Transport Operation Example of Machine Enable Jog and Shuttle Operation Jog On / Off Feature Shuttle Jog Controller CommandsMMC and 9 Pin Commands Jog Jog and Shuttle Speed Locate Operation Smpte Mode vs Feet and Frames Storing a Locate by Capturing on the Fly Sending a Locate Command Last function More About Sending Locate CommandsLocating by Direct Address Attributes of the Function Buttons Function Buttons Section F and M Buttons have LEDs Remote Control of the LEDsM Buttons Have More Than One Purpose Cursor Buttons Have More Than One Purpose Assigning Function Buttons To Assign an F or M Button Editable Parameters for the Function Buttons F and M Name M Button Command Types About Query Mode Maximum or Velocity To Assign a W or Cursor Button Editable Parameters for Function Buttons Cursor & W Name Transport and M Button Commands Number Function Button Operation Notes Switch Grouping System Section Entering Utility ModeExiting Utility Mode Dump Mode Manually Exiting Special ModeProtect Bank Name Showtc Jog Program Change Mode Program Change Mode Display Locates or Display Program Changes Time Code Display Technical Information Dimensions Initialization Initialized SettingsSwitch Midi Channel Controller # Switch Midi Chan Controller# Encoders Midi Chan Controller# Touch Midi Chan Controller # Fader Midi Chan Controller #Page Warranty Memory Initialization Manually Switching ModesQuick Operation Reference Fader Wave Demo To Assign a Control Bank Switchable ControlsLCD Displays Encoder Names or Bank Name Shiftable Controls Editable Parameters Name Command TypesM Buttons Command Menu Also Includes Query If 9 Pin or GPI Cards are Present, M Commands IncludeButtons Have Two Uses Jog Wheel and Shuttle Ring More About Groups Time Code Display Locate Mode Offset Feet and Frame Entering and Exiting Utility Mode Ethernet Interface Card Installation and Configuration II. Initialization III. Operation