Transport and M Button Commands | JL Audio MCS-3800 guide

Editable Parameters for Function Buttons (Cursor & W)

Name

Press the Cancel/Clear key in the Keypad to clear the name. Use the Cursor buttons to the left of the LCD to move the cursor. Turn the first encoder to dial in the letters and numbers.

The top row of the LCD show the control's real (permanent) name.

The bottom row of the LCD is the user editable name.

Transport and M Button Commands

•Off (that is, sends no command)

•Note

•Ctrl (Controller)

•P Change (Program Change)

•Query (Puts MCS Controller nto Query Mode.)

•Jog (Turns Jog /Shuttle Wheel On and Off)

•GMaster (Turns Grand Master Fader On and Off)

•Play (MMC and or 9 Pin Play)

•Stop (MMC and or 9 Pin Stop )

•REW (MMC and or 9 Pin Rewind)

•FF (MMC and or 9 Pin Fast Forward)

•REC (MMC and or 9 Pin Record)

•RTZ (MMC and or 9 Pin Return to Zero)

•SLOPLAY (MMC and or 9 Pin 1/2 speed play)

•RV PLAY (MMC and or 9 Pin Reverse Play)

•EJECT (MMC EJECT)

•CHASE (Puts MMC or 9 Pin machine into Chase Mode.)

About Query Mode

When a switch is set to Query, it will not send a command. When pressed, it puts the whole unit into Query mode. In Query mode, no commands are sent, but the LCD will display all the assignment parameters for the last control activated.

74

Image 74

JL Audio MCS-3800 manual Editable Parameters for Function Buttons Cursor & W Name, Transport and M Button Commands

Contents

MCS-3000 Series Media Command Stations About this Manual Introduction Table of Contents Mixer Section Transport Section System Section Warranty Quick Operation Reference 7 Page SummaryFunction Buttons Section Technical Information Getting Started Front Panel Displays and Controls Mixer Section Function Buttons Section Transport Section System Section Rear Panel Page Expander Connection Mounting MCS-3000X Expander to Controller Move Left End Bell 3000X Expander Electrical Hookup Set the Expander ID# Important Be Sure Each Expander has a Unique ID#Page Time Code PowerSystem Connections Midi In and Out Card Slots #1 and #2 OMS or Free Midi Definitions Basic Operation Power UpEntering and Exiting Assign Mode LCD and Page Buttons Modes of Operation More About User Assignable Mode More About Special Mode LED Behavior in Special Mode Manually Exiting Special Mode User Assignable vs. Pre-Defined Functionality Wave Demo Attributes of the Mixer Section This chapter relates to User Assignable Mode OnlyMixer Section Basic Bank Switching and Encoder Selection Encoder Selection Fader Output Fader Input Channel Switches Touch Sensor Encoders, Select Assigning Mixer Controls An Overview To Assign a Fader or a Touch Sensor Number CommandEditable Parameters for the Faders and Touch Sensors Name Channel Group GMaster To Assign the Rotary Encoders Editable Parameters for the Rotary Encoders Name To Assign Mute, Solo, Aux and Select Buttons Editable Parameters for Mute, Solo, Aux, and Select Name Minimum or Release Velocity Maximum or Velocity Latch Mixer Operation Notes Banks Remember Last Fader Position Touch Inhibits Motor Encoders Fader Groups Traverse Banks Group Members are Automatically Scaled Grand Masters Require Grand Master On Switch Grand Masters Traverse All Banks Moving Faders with Midi Data Created Off Line Page Transport Section Attributes of Transport Section Buttons Transports Jog Wheel and Shuttle Ring Locates Assigning Transport Controls To Assign a Transport or M Button Editable Parameters for Transport and M Buttons Name If 9 Pin or GPI cards are present Transport and M Button Command TypesAdditional M Buttons Command Menu Items About Query Mode Maximum or Velocity Transport Operation Record Safety FeatureM5 enables CS-10 Emulation Initialized State of Transports and M Buttons Example of Machine Enable Jog On / Off Feature Jog and Shuttle Operation Shuttle Jog Controller CommandsMMC and 9 Pin Commands Jog Jog and Shuttle Speed Smpte Mode vs Feet and Frames Locate Operation Sending a Locate Command Storing a Locate by Capturing on the Fly Last function More About Sending Locate CommandsLocating by Direct Address Function Buttons Section Attributes of the Function Buttons Cursor Buttons Have More Than One Purpose Remote Control of the LEDsM Buttons Have More Than One Purpose F and M Buttons have LEDs Assigning Function Buttons To Assign an F or M Button Editable Parameters for the Function Buttons F and M Name M Button Command Types About Query Mode Maximum or Velocity To Assign a W or Cursor Button Transport and M Button Commands Editable Parameters for Function Buttons Cursor & W Name Number Switch Grouping Function Button Operation Notes System Section Entering Utility ModeExiting Utility Mode Dump Mode Manually Exiting Special ModeProtect Showtc Bank Name Jog Program Change Mode Program Change Mode Time Code Display Display Locates or Display Program Changes Dimensions Technical Information Initialization Initialized SettingsSwitch Midi Channel Controller # Switch Midi Chan Controller# Encoders Midi Chan Controller# Fader Midi Chan Controller # Touch Midi Chan Controller #Page Warranty Fader Wave Demo Manually Switching ModesQuick Operation Reference Memory Initialization Shiftable Controls Bank Switchable ControlsLCD Displays Encoder Names or Bank Name To Assign a Control Editable Parameters Name Command TypesM Buttons Command Menu Also Includes Query If 9 Pin or GPI Cards are Present, M Commands IncludeButtons Have Two Uses More About Groups Jog Wheel and Shuttle Ring Locate Mode Time Code Display Entering and Exiting Utility Mode Offset Feet and Frame Ethernet Interface Card Installation and Configuration II. Initialization III. Operation