Press Call key for forced transmission | Furuno FS-5070 manual

5. ROUTINE MESSAGE CALLING, RECEVING

13.Press the CALL key to send the individual call (transmission time: about seven seconds). The display shows the message “Individual routine message in progress!” while the call is being sent.

Individual routine message in progress!

DESTINATION ID:		123456789
PRIORITY	:	ROUTINE
TELEPHONE		2138.0 kHz

DSC FREQ :		2177.0 kHz
TIME TO GO:		7S

Note: When the channel is in use, "CH BUSY" appears at the lower left-hand side of the screen.

Press CALL key for forced transmission.

After the call is sent, the equipment waits for acknowledgement of the call, showing the display below.

Waiting for acknowledgement.

DESTINATION ID: 123456789

PRIORITY	: ROUTINE
TELEPHONE	2138.0 kHz
DSC FREQ :	2177.0 kHz

TIME TO GO: 4M30S RESENDING

The timer starts counting down the maximum time to wait for acknowledgement, five minutes. One of the following three messages appears. (“No response! Try calling again?” appears after the timer counts down to zero. It means the receiving station did not respond.)

Able acknowledge message received.

CANCEL: STOP ALARM

PRIORITY	: ROUTINE
TELEPHONE	2138.0 kHz

Unable acknowledge message received.

CANCEL: STOP ALARM

SENDER ID	:	123456789
PRIORITY	:	ROUTINE

No response!

Try calling again?

DESTINATION ID:		123456789
PRIORITY	:	ROUTINE
TELEPHONE		2138.0 kHz
DSC FREQ	:	2177.0 kHz

RESEND

Able acknowledge call received		Unable acknowledge call received			No response from station
				(appears when the timer counts to "zero")
				(appears when the timer counts to "zero")

14.Do one of the following depending on the message shown in step 12.

5-5

Image 65

Furuno FS-5070 manual Press Call key for forced transmission, Able acknowledge message received

Contents

Model FS-5070 00016050112 Important Notice Safety Instructions Iii For IC-302 option operation Distress Alert Message Procedure Distress Cancellation Proc. Select frequency Push Enter Canceling Distress Alert Communicate, via radiotelephone, with the coast station Send cancel msg. by voice on 2182.0 kHz Table of Contents Send calls Viii Menu Operation Nbdp TRANSMITTING, Receiving 11-1 11.111.2 11-2 Foreword FeaturesXii General Xiii Program Number Standard configuration is shown with solid line System ConfigurationsXiv FS-1570 Terminal Unit FS-2570 FS-5070 Xvi Operational Overview PWR/VOL knob Turns the power on/off Adjusts volumeControls Description of controls Radiotelephone RT screen Turning the Power On/OffRadiotelephone RT Screen DSC standby screen DSC Standby ScreenIndication Loudspeaker Setting Scan FrequenciesControl Unit Dimmer, Contrast System Characteristics Setting for Auto AcknowledgementEquipment priority Controls become inoperative Intercom Automatic setting of working frequency Choosing Class of Emission SSB Radiotelephone Choosing channel Choosing Channel, FrequencyChoosing band and band channel with the Enter knob Rotate the Enter knob to set band or channel desired Transmitting Transmitting procedureChoosing frequency Entering frequency with the numeric keys Condition of the transmitting unit Reducing transmitter power Checking the transmitting power RF gain sensitivity adjustmentRotate the Enter to adjust and then push the Enter knob Receiving Squelch function Receiving AM broadcasting stationsNoise blanker Squelch on/off High Tension Hazard When Automatic Tuning Fails User Channels DSC Overview What is DSC?DSC Message Call Description Contents of a DSC call Alarm Frequency interval Audio Alarms Distress receive call Interpreting Call DisplaysReceive calls Individual receive call Send callsReceived message View message Compose msg Individual send call Sending Distress Alert Distress OperationsDistress operation overview Ship in Distress Distress Operations Received message Push the Enter knob to open the latitude input window Push the Enter knob to open the Input Type menuTwice and then go to step Compose msg Push the Enter knob to open the time input window Communicating by Nbdp Terminal Unit Display changes as below example Distress alert received on MF band Receiving a Distress Alert Action for ship receiving distress alert on MF band Distress alert message received Distress acknowledge message in progress Distress alert received on HF band Agree Action for ships receiving distress alert on HF band Sending the distress relay to coast station on HF band Wait for distress relay acknowledge Push the Enter knob to open the DSC FREQ. Menu Sending distress relay to coast station Sending Distress Relay on Behalf of a Ship in Distress Ship ID in Dist Push the Enter knob to open the Ship ID in Dist window Telephone Priority distress Transmit sure? Press the Cancel key to silence the audio alarmDistress relay coast message in progress Distress relay ack message received Area Circle Sending distress relay to area ships Ship ID in Dist Nature Telephone Distress relay area message in progress Receiving Distress Relay from Coast Station Cancelling Distress Call Distress Cancellation Proc. Select frequency Push Enter Individual Call Routine Message CALLING, ReceivingSending an individual call Operation overview NBDP-ARQ Push the Enter knob to open the Priority menu Routine priority How to Set Working Frequency, ChannelSafety or urgency priority Compose msg How to Set DSC Frequency Able acknowledge message received Press Call key for forced transmission Unable acknowledge call received Able acknowledge call received No response! Try calling again? Receiving an individual callSend Able acknowledge Send Unable acknowledge Manually Sending automatic acknowledge ACK BQ with comply type Able Unable acknowledge message in progress Sending automatic acknowledge ACK BQ with comply type Unable Manually acknowledging individual call with Able Manually acknowledging individual call with Unable No Reason Reason Busy Press the 2/DSC key Select Message Group CallSending a group call MHZ Sending message by Nbdp Terminal Unit Receiving a group call Receiving message by Nbdp Terminal Unit Geographical Area Call Area Sending a geographical area call Receiving a geographical area call Geographical Area Sender ID Sending a neutral craft call Neutral Craft Call Receiving a neutral craft call Sending a medical transport call Medical Transport Call 2187.5 Receiving a medical transport call Automatic reply Press the Cancel key to return to the radiotelephone screenReceiving a Polling Request Manual reply Requesting other ship’s position Position CallFinding position of other station Sending own ship’s position to other station Station ID Position call other ship requests your position Cancel call Press the Cancel keyAcknowledge message received Automatic reply Manual reply If canceling to send the reply, press the Cancel key Sending a Pstn call, receiving acknowledge back ACK BQ Pstn Call To scroll Push the Enter knob to open the TEL NO. menu Waiting for acknowledgement Unable acknowledge message received Receiving a Pstn call, sending acknowledge back ACK BQThen, one of the following displays appears Shortly thereafter, one of the following messages appears No response! charge information Manual Deleting log files To view the contents of a file, do the followingTo return to the log selected, press the Cancel key This page is intentionally left blank Menu Operation Adjusting Handset VolumeSetup Squelch Frequency Noise BlankerRegistering user channels User ch entry Push the Enter knob to open the user channel options window Deleting user channels Preparing TX MessagePreparing individual calls Deleting individual user channels Frequency Push the Enter knob to open the Station ID entry window Push the Enter knob to open the file name entry window How to Enter File Name and Number Push the Enter knob to continue Preparing group calls Message 2 MHZ Preparing Pstn calls Preparing test call Deleting send message Sending prepared messagesSending without modification Editing before sending Deleting all messages Manual Entry of Position and TimePrinting List of Send Message Files After last digit Date/Time setup Date and Time SettingMemory Clear Memory clear Clearing transmitted log Clearing received ordinary logClearing received distress log Clearing user channels Setting AlarmsRestoring to default setting Sound setup Sound Setting OFF Hook Setting the Auto ACK Details Sample printouts Printing Messages Distress and safety frequencies Routine frequencies Scan freq setup Special Messages Key assign setupKey Assignment Operation Timer Off FAX Enable/DisableSpeaker Setting in Off Hook This page is intentionally left blank Nbdp terminal unit, printer and keyboard Nbdp System OverviewTurning on the Nbdp System Description of Equipment Features of the IB-583Terminal unit Communication status display Keyboard Keyboard Menu conventions Function Keys, Menu OperationInverse video Underline Selecting menus Menu overviewFile menu Selecting menu items and options Function key description Undo Function key F2 Edit menuCut Copy Timer Operation Cancel SendingFunction key F3 Operate menu Call Station Function key F4 Window menu Or month, choose item with ↑ or ↓ key and change settingWindow menu Displays desired calendar month and year. To change year Function key F5 Station menu Timer Operation EntryStation Entry Scan Entry Slave Delay SetupFunction key F6 System menu TX/RX MSG Save Function key F10 Break Disconnects the line Cursor is choosing Window Color Setup press the Enter key Registering Answerback Code & ID Codes Nbdp PreparationsRegistering answerback code Answerback code entry screen Message for confirmation of code entered Registering ID codesIf the code is correct, press the Enter key again ID code entry screen Registering stations Station List Scanning group list OK/Cancel promptEditing/Deleting stations Registering timer programs Timer ProgrammingTimer operation entry screen 3 5 0 User channel entry screen Editing/Deleting timer programs Editing/Deleting user channels Scan Channel GroupsRegistering scan channel groups Scan entry screen Press the Enter key twice Press the ESC key Editing/Deleting scan channel groups Opening and Closing Files Nbdp File OperationsCreating Files How a file is opened Formatting floppy disks Saving a File Saving a file Editing FilesCutting and pasting text Close text screen Cutting text Copying and pasting textHighlight Pasting text Select all Copy and paste flow diagramSearching text Search screen Goto line Replacing textGoto top, Goto bottom Replace screen Opening Files Switching between filesRenaming Files Opening a file Deleting Files Saving a File Under a New NameReal Time Printing Printing Files Manual Calling Nbdp TRANSMITTING, Receiving10-1 Set frequency screen Manual calling screen 10-2 10-3 ARQ Mode OperationEstablishing connection Press the 1 key to choose Call Station Transmit message by one of the following methods 10-4Sending a file stored on a floppy disk Send file screen Choosing Receive Mode FEC Mode Operation10-5 Stopping transmission Communications example Communication Example10-6 Table of abbreviations 10-7 Enabling timer operation Timer OperationCommand and abbreviation Timer operation list 10-9 Stopping timer operationScanning Preparing Macrofiles for Automatic Telex Communication BufferAutomatic telex overview 10-10 10-11 PreparationsRegistering answerback code Registering scan groups Command Parameter Content CommandsCommands processed by Danish coast station Lyngby Command Function 10-13 Actual procedure for store-and-forward telexStore-and-forward method Close text prompt 10-14Sample macrofile for store-and-forward method 10-15 Dirtlx macrofileSample Dirtlx macrofile Sample Dirltx macrofile 10-16 Procedure for Dirtlx Basic procedure Automatic Telex using MacrofileActual procedure 10-17 Press the ↓ key to choose a macrofile Press the Enter key 10-18Call macro screen 11-1 Maintenance & TroubleshootingRadiotelephone Test 11-2 Maintenance FS-5070 only Simple Troubleshooting11-3 11-4 Error MessagesError messages 11-5 Replacement of Fuses 11-6 Test Call Test acknowledge message received 11-7Do the either way depending on the message shown in step Nbdp Terminal Unit Maintenance System menu Example IB-583 11-9Self test results Tone test Tone test 3 Beta 11-10Tone test 2 Fox AP-1 AppendixMenu Tree AP-2 Nbdp terminal unit telex AP-3 Frequency TablesTX kHz RX kHz Remarks File Name 14. = Ship-to-ship AP-4 Custom channels to be programmed by Furuno dealers AP-5 MF band working carrier frequencies ref. US CFR 47 Part AP-6 MF band SSB working carrier frequencies AP-7 MHz ITU SSB carrier frequencies ITU RR Appendix AP-8 AP-9 12/16 ITU SSB carrier frequencies ITU RR Appendix AP-10 18/19, 22, 25/26 ITU SSB carrier frequencies ITU RR Appendix AP-11 MF band telex frequency table Frequency /4 AP-12 ITU Telex frequency /4 AP-13 AP-14 ITU Telex Frequency /4 AP-16 Telex Abbreviations Sentences Digital Interface IECAP-17 Input sentences IEC ZDA Time and date AP-18GLL Geographic position latitude/longitude GNS Gnss fix data AP-19 RMC Recommended minimum specific GPS/TRANSIT data AP-20 AP-21 Schematic diagram Transceiver unit FS-1570T Parts ListAP-22 Transceiver unit FS-2570T AP-23 Control unit FS-2571C AP-24 Control unit FS-5070T AP-25 AP-26 Parts LocationFS-1570T AP-27 Transceiver unit FS-2570T AP-28 Transceiver unit FS-5070T Comb AP-29 AP-30 Control unit FS-2571C FS-1570/2570/5070 Specifications of SSB Radiotelephone DSC/WATCH Keeping Receiver DSC/WATCH Receiver FS-5070 Terminal Unit IB-581 FS-1570/2570 Nbdp Function Option Antenna Coupler FS-5070 Antenna Coupler FS-1570/2570 Coating Color Distress relay Index IN-2 0560 Publication No. DOC-1028 0560