Custom Door Panel Dimensions Using Standard Trim | GE ZIR36N RH

Custom Panel Dimensions

36″ Refrigerators, Freezers

Custom Door Panel Dimensions Using Standard Trim

Using Trim Kit ZKTR36LH or ZKTR36RH 3/4″ thick panel with custom handle

35 1/4 "

3/4" Thick

Custom Panel

With Custom

Handle

68-15/16"

Custom Grille Panel

35 1/4"

A	3/4" Thick Panel

Grille Panel height can vary to fill installation height.

Installation Height	Dimension A
83-1/2″	7-3/4″
84″	8-1/4″
84-1/2″	8-3/4″

IMPORTANT: Maintain 1-1/2″min. gap between top of door and bottom of grille panel.

Unified Custom Grille Panel

71-3/8"

ZIR36N Refrigerator

ZIF36N Freezer

•The ZKTR36LH (or ZKTR36RH) trim kit installed together with a ZKHTR1 custom handle kit provides for the installation of 3/4″ thick custom door and grille panels with a custom handle of your choice. Order ZKHTRSS1 for a tubular stainless steel handle. Cut panels to size, rout the handle side of the panel as shown below and install.

IMPORTANT: Maximum door panel weight is 67 lbs., maximum grille panel weight is 9 lbs.

Rout back side of panel as shown

on the handle side 1-13/16"

1/4"
max	Appearance Side

A

3/4" Thick Panel

10

Image 10

GE ZIR36N RH, ZIR36N LH, ZIF36N RH, ZIF36N LH installation instructions Custom Door Panel Dimensions Using Standard Trim

Contents

Installation Instructions Contents ING Design Information 36″ Refrigerators, Freezers When Installed into a corner Side By Side Installation Freezer Refrigerator Advance planning exterior appearance options Installation Between Base Wall CabinetsInstallation At End-of-Run ″ thick custom panels-Without trim kits Trim kit ModelsAvailable Descriptions Custom Panel Dimensions Clearances ″ Panel Cut panels to size 35-1/16 Handles 35 -1/16 Custom Door Panel DimensionsDimension a Unified Custom Grille Panel 71-3/8 Thick Panel Custom Door Panel Dimensions Using Standard Trim Trim ″ Side Panels Insert end23 5/16 Flooring InstallationMaterials Required Grounding the Refrigerator Step Remove Packaging Water Line InstallStep Shut off the main water supply Illustration B Step Install Side PanelsIllustration a ″ to 3/4″ Side Panels Leading edge of side Step Secure LevelOr Freezer To Sides Door panels Install 1/4″Power Step Check Alignment Adjust DoorTemperature Controls Arrange Interior To change grille panel size Grille Panel Frame AdjustmentZGC2 Trim Kit Pieces Support for Custom Handles Parts ListZKHR1 Trim Kit For 1/4 ″ Panels Tools and materials required ZKHR1 Trim Kit For 1/4″ Panels Door using at least 2 screwsReinstall original screws into the door extrusion Locate handle position ZKTR36LH/ZKTR36RH Trim Kit ″ Custom Panels Install panels Back Side Custom Panel Grille Install Handles StepAdjust Panel height Top of the screws are 1/16″ from the surface Install four of the six larger undercut screws so thatGrille panel Part List ZKHTR1 Trim Kit For 3/4″ PanelsTools and materials required Before Position Temporarily mount door panelLocate Assemble Mount assembled panel ZKHRSS1 Trim Kit For 1/4″ Panels Tubular Stainless Steel Handles On the back side of the panel-at the handle side If you are installing handle onto a Stainless Steel PanelStep Match handle extrusions to handle Measure and mark 1/4″ below the top edge Step Install handles and panels Step Install standoffs onto handlesDecorator Raised Panel on 1/4″ Thick Backing Before you ZKHTRSS1 For 3/4″ PanelsKit Begin To Panel Using the Allen wrench provided. The standoffMatch Handle Should be tight against the handle ZUG75 Trim Kit Step Install Spacer PadsUnified 3/4″ Custom Grille Panel Kit Refrigerator and freezer must be secured to prevent tipping Roll Both Products into OpeningStep Level Both Products Step Remove Wire Fence and Switch Cover Install CenterTrim Strip Step Install Grille Base Cover Remove Grille Frame Unified Base Cover Step Install Soffit Vent Top Secure Custom Panel To Support Removing side screws. Discard top piece, retain Step Adjust Door Alignment