Step 4A
Install handles and panels
FOR
STAINLESS
STEEL
PANELS
ZKHRSS1 Trim Kit (For 1/4″ Panels)
Tubular Stainless Steel Handles
|
|
|
|
|
|
|
|
|
|
|
| Screw |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Extrusion | |
|
|
|
|
|
| Corrugated | Spacer |
| ||||||||
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
| Ring |
| |||||
|
|
|
|
|
| Stainless |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Panel |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Handle |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
| • Slide panel into the door trim. Leave about 4″ | ||||||||
|
|
|
|
|
|
|
| |||||||||
• Crimp top and bottom edges of corrugated. | ||||||||||||||||
• Slide corrugated into door trim. Leave about 1/4″ |
| of the panel exposed to allow room to install | ||||||||||||||
gap between edge of corrugated and hinge side |
| the handle extrusion. |
| |||||||||||||
trim of the door. | • Place a spacer ring over each screw hole on the | |||||||||||||||
|
|
|
|
|
|
|
|
| extrusion. Use tape to hold in place. | |||||||
NOTE: Panels have a protective plastic covering. Peel | • Place extrusion onto panel. Use a pencil to punch | |||||||||||||||
away just enough to allow panel to slide into trim and to |
| hole in tape covering spacer rings and align with | ||||||||||||||
clear handle mounting screws. The plastic covering will |
| screw holes. |
| |||||||||||||
keep the panel clean during the installation process. | • Install mounting screws through the extrusion and | |||||||||||||||
Be sure to maintain 1/4″ gap between corrugated |
| panel. |
|
|
|
|
|
|
| |||||||
• Drive screw part way through the top standoff, | ||||||||||||||||
and hinge side trim. |
| then part way through the bottom standoff. Install | ||||||||||||||
|
|
|
|
|
|
|
|
| remaining standoffs part way. |
| ||||||
|
|
|
|
|
|
|
| • Drive screws until the handles are tight against | ||||||||
the panel.
• Slide the assembly into the door trim until the extrusion fits firmly against the steel door.
• Reinstall original screws into the door extrusion.
Raised Panel on 1/4″ Thick Backing:
A raised panel design secured to a 1/4″ thick backing (screwed or glued) can be used with this handle kit.
•Cut the 1/4″ thick panels to size.
•Fabricate the raised panel to allow
•Allow 5/16″ clearance at the other edges to allow for the trim flange.
•Total panel thickness should not exceed 3/4″.
•Countertops adjacent to the refrigerator installation should be mitered 45°.
NOTE: Longer Screws, obtained locally, will be required
| Raised Panel on 1/4" Thick Backing | |
1/4" | Appearance | 5/16" Clearance |
| ||
Thick | Panel | Custom Panel |
Backing |
| |
5/16" | ||
Clearance | ||
Clearance | ||
handle Side | ||
hinge side | ||
| ||
| 5/16" Clearance |
to accommodate panel thickness. Use stainless steel | 5/16" Clearance |
|
32
