IT5800 Product Specifications | Hand Held Products IT5600 specs

IT5800 Product Specifications

Parameter	Specification

Dimensions (Typical):	without aimer		with aimer
Height	6.4 inches (16.3 cm)		6.5 inches (16.5 cm)
Length	5.3 inches (13.5 cm)		5.3 inches (13.5 cm)
Width	3.2 inches (8.1 cm)		3.2 inches (8.1 cm)
Weight	7.5 ounces (213 g)		8.4 oz. (238 g)

Light Source	630 nm visible red LED

Aimer Beam Light Source	Class 2 Laser Product, 1.0 mW Max Output:650 nm

Scan Rate	270 scans per second in most usages

Skew Angle	±65 degrees

Pitch Angle	±65 degrees

Horizontal Velocity	2 inches (5 cm) per second

Scan Contrast	20% minimum

Voltage Requirements	4.5 to 12VDC at scanner

Current Draw (Max):	Scanning	Standby	Inrush	Low Power
5800SR00X Model @5Vdc	235mA	68mA	350mA	100µA
@12Vdc	142mA	48mA	-	-

5800SR05X Model @5Vdc	235mA	68mA	350mA	100µA
@12Vdc	127mA	48mA	-	-

5800SR03X Model @5Vdc	210mA	60mA	350mA	100µA
@12Vdc	120mA	49mA	-	-

Temperature Ranges:
Operating	-22°F to +122° F (-30°C to +50° C)
Storage	-40°F to +140° F (-40°C to +60° C)

Humidity	0 to 95% non-condensing

Mechanical Drop	Operational after 50 drops from 6.5 feet (2 m) to
Mechanical Drop	concrete @ -22°F (-30°C)
	concrete @ -22°F (-30°C)

Vibration	Withstands 5G peak from 22 to 300 Hz

ESD Sensitivity	15 kV to any external surface

Sealant Rating	IP 54 (Water and Dust Resistant)

	FCC Class B, CE EMC Class B, CE Low
Agency Compliance	Voltage Directive, EN60825-1 LED Safety; Class 1,
	UL, cUL, TÜV Certified to EN60950, C-Tick, NOM

IT5600/IT5800 User’s Guide

12 - 3

Image 143

Hand Held Products IT5600 manual IT5800 Product Specifications

Contents

User’s Guide Disclaimer Canadian Notice Statement of Agency ComplianceFCC Class B Compliance Statement TÜV Statement LED Safety StatementAimer Beam Safety Statement IT5800 Option only UL and cUL Statement Solids and Water Protection MexicoPatents Page Table of Contents Output Data Editing Symbologies Check Digits Required Code 11 Message Length Interface Keys Serial Programming Commands Appendix a Appendix a Unpacking the Scanner Getting StartedIT5600/5800 About This Manual Models Primary Interfaces Secondary IT5600 ModelsIT5800 Models IT5600/5800 Scanner Identification IT5800 Scanner with aimer beam option Identification Connecting the Scanner When Powered by Host Keyboard Wedge Good Read Bad Read Resetting the Standard Product DefaultsReading Techniques Plug and Play RS-232 Option SettingKeyboard Wedge Connection Laptop Direct Connect IBM 4683 Ports 5B, 9B, and 17 Interface Wand Emulation Plug & Play UPC a UPC E Symbology Suffix IBM SurePos Connecting the Scanner with USB USB HID USB PC or Macintosh Keyboard USB Com Port Emulation Connecting the Scanner with Serial Wedge Default = P1 Both P1 and P2 IT5600/IT5800 User’s Guide Terminal ID Terminal Interfaces Terminal Models Terminal ID Supported Terminals USB Hidpos Keyboard Country Keyboard Style Keyboard Modifiers IT5600/IT5800 User’s Guide Connecting the Scanner with RS-232 Serial Port RS-232 Baud Rate RS-232 Word Length Data Bits, Stop Bits, and Parity Wand Emulation Connection RS-232 Handshaking Wand Emulation Polarity Wand Emulation Transmission Rate Data Block Size Wand EmulationWand Emulation Idle Overall Checksum Delay Between Blocks Beeper Good Read Good Read IndicatorsBeeper Volume Good Read Output Number of Beeps Good Read Beeper Duration Good ReadLED Good Read Manual/Serial Trigger Good Read DelayUser-Specified Good Read Delay Trigger Modes Read Time-Out Automatic Trigger Hands Free Time-Out Reread DelayPresentation Mode User-Specified Reread Delay User-Specified Aimer Beam Delay Aimer Beam Delay Aimer Beam option onlyAimer Mode Aimer Beam option only Centering Window Aimer Beam Time-Out Aimer Beam option only IT5600/IT5800 User’s Guide Output Sequence Overview Output Sequence Example Output Sequence EditorRequire Output Sequence SEQBLK62001141FF6A001242FF69001143FF SEQBLK62999941FF6A999942FF69999943FF No Read Multiple Symbols Video Reverse Points to Keep In Mind Data EditingPrefix/Suffix Overview Scan Add Suffix Scan the Add Prefix or Add Suffix symbolTo Add a Prefix or Suffix Prefix Selections To Add a Carriage Return Suffix to all SymbologiesScan the Clear One Prefix or Clear One Suffix symbol To Clear One or All Prefixes or Suffixes Function Code Transmit Intercharacter, Interfunction, and Intermessage DelaysSuffix Selections User Specified Intercharacter Delay Intercharacter Delay Intermessage Delay Interfunction Delay To Add a Data Format Scan the Enter Data Format symbol Primary/Alternate FormatData Formatting Data Format Editor Introduction Clear One Data Format Data Format Editor CommandsEditor Commands Other Programming Selections Move Commands Data Format Editor Alternate Data Formats Data Formatter IT5600/IT5800 User’s Guide Enabling the Secondary Interface Secondary Interface Secondary Code 39 Wand Emulation Secondary RS-232 Connection Laser Emulation Transmission Rate Secondary Laser Emulation Laser Emulation Idle Secondary Trigger ModeLaser Emulation Polarity Hands Free Time-Out IT5600/IT5800 User’s Guide Introduction SymbologiesAll Symbologies Message Length Codabar Check Character CodabarCodabar Start/Stop Characters Codabar Codabar Concatenation Code 39 Start/Stop Characters CodeCodabar Message Length Code 39 Message Length Code 39 Check Character Code 32 Pharmaceutical Paraf Code 39 Append Full Ascii Check Digit Interleaved 2Code 39 Code Interleaved 2 of 5 Message Length Code 93 Code Code 93 Message Length Code 2 of 5 Message Length Code 2Iata Code 2 Iata Code 2 of 5 Message Length Matrix 2 Check Digits Required Matrix 2 of 5 Message Length Code 11 Message Length Code 128 Code Isbt 128 ConcatenationCode 128 Message Length Telepen Output TelepenCode 128 Function Code Transmit UPC a Number System Telepen Message LengthUPC a Check Digit IT5600/IT5800 User’s Guide UPC a Addenda Separator UPC aUPC a Addenda UPC a Addenda Required UPC E0 and UPC E1 UPC-A/EAN-13 with Extended Coupon Code UPC E0 and UPC E1 Addenda Separator UPC EUPC E0 and UPC E1 Expand UPC E0 and UPC E1 Addenda Required UPC E0 Addenda UPC E0 Check DigitUPC E0 Number System EAN/JAN 13 Addenda EAN/JAN 13 Check Digit Isbn Translate EAN/JANEAN/JAN 13 Addenda Required EAN/JAN 13 Addenda Separator EAN/JAN 8 Addenda EAN/JAN 8 Check Digit EAN/JAN 8 Addenda Separator EAN/JAN 8 Addenda Required MSI Message Length MSIMSI Check Character Plessey Message Length Plessey CodeRSS-14 RSS Expanded RSS Limited RSS Expanded Message Length Eanucc Emulation China Post Message Length China Post Code Korea Post Message Length Korea Post Code PosiCode Message Length PosiCodePosiCode a and B Codablock F Message Length Trioptic CodeCodablock F Code 16K Message Length Code 16K Code 49 Message Length IT5600/IT5800 User’s Guide Function Code HEX/ASCII Value Full Ascii Ctrl + Interface KeysKeyboard Function Relationships Country Codes Supported Keys Supported Interface KeysIBM AT/XT PS/2 Compatibles IBM XTs IBM, DDC, Memorex Compatibles Telex, Harris SYN PF1 ETB PF2 Can PF3 PF4 SUB PF5 ESC PF6 PF7 PF8 PF9 Memorex Telex Ansi Ascii HEX Esprit 200 Apple Mac/iMac Show Data Format To Add a Test Code I.D. Prefix to All SymbologiesUtilities Show Software Revision Temporary Visual Menu 2003 Configuration Visual Menu 2003 Operations Installing Visual Menu 2003 from the WebVisual Menu Visual Menu 2003 Introduction IT5600/IT5800 User’s Guide Conventions Serial Programming CommandsMenu Command Syntax Responses Query CommandsConcatenation of Multiple Commands Examples of Query Commands ActivateSYN T CR DeactivateSYN U CR Trigger Commands Setting Serial Selection Command Menu Commands TERMID64 BEPLVL3 Output Selections BEPBIP0 Prefix/Suffix Selections Selections Data Formatter Selections C39SSX1 Symbologies C39ASC0 C39ASC1 C11DFT UPAENA0 UPAENA1 EAN/JAN MSIENA0 MSIENA1 CPCMIN## IT5600/IT5800 User’s Guide Parameter Specification Product SpecificationsIT5600 Product Specifications IT5600 Depth of Field IT5800 Product Specifications Min. Bar Max Min. Far Field Width Near Field IT5800 Depth of Field Bar Image StandardCompatible Standard Cable Pinouts Standard Cable Serial Output Standard Cable Standard Cable Pinouts IT5600/IT5800 User’s Guide Inspecting Cords and Connectors MaintenanceMaintenance Cleaning the Scanner’s Window To Replace the IT5600 Interface Cable Replacing the Interface Cable To Replace the IT5800 Interface Cable Troubleshooting Is the bar code displayed but not entered? Customer Support Product Service and Repair Online Technical Assistance Limited WarrantyOnline Product Service and Repair Assistance Technical Assistance IT5600/IT5800 User’s Guide IT5600/IT5800 User’s Guide Appendix a Symbology ChartSymbology Code Hex Symbology Code Hex Char Dec Ascii Conversion Chart CodeDec Hex Char IT5600/IT5800 User’s Guide CP ISO646 Code Page Mapping of Printed Bar CodesPage Page Interleaved 2 Code Codabar Programming Chart UG Rev C 6/05