Delay Between Blocks, Overall Checksum | Hand Held Products IT5600

Delay Between Blocks

Note: This option is not applicable to Laser Emulation Raw Output (see Secondary Laser Emulation on page 6-3).

This sets the delay time between data blocks. Default = 50ms.

5ms

* 50ms

150ms

500ms

Overall Checksum

Note: This option is not applicable to Laser Emulation Raw Output (see Secondary Laser Emulation on page 6-3).

When this option is turned on, a computed check character is added at the end of the entire message. The check character is the character which when Exclusive-OR’d with every preceding character of the message yields a result of 0x00 (00H). Default = Off.

On

* Off

2 - 14

IT5600/IT5800 User’s Guide

Image 42

Hand Held Products IT5600, IT5800 manual Delay Between Blocks, Overall Checksum

Contents

User’s Guide Disclaimer Statement of Agency Compliance FCC Class B Compliance StatementCanadian Notice UL and cUL Statement LED Safety StatementAimer Beam Safety Statement IT5800 Option only TÜV Statement Mexico PatentsSolids and Water Protection Page Table of Contents Output Data Editing Symbologies Check Digits Required Code 11 Message Length Interface Keys Serial Programming Commands Appendix a Appendix a About This Manual Getting StartedIT5600/5800 Unpacking the Scanner IT5600 Models IT5800 ModelsModels Primary Interfaces Secondary IT5600/5800 Scanner Identification IT5800 Scanner with aimer beam option Identification Connecting the Scanner When Powered by Host Keyboard Wedge Plug and Play Resetting the Standard Product DefaultsReading Techniques Good Read Bad Read Laptop Direct Connect Option SettingKeyboard Wedge Connection RS-232 Wand Emulation Plug & Play IBM 4683 Ports 5B, 9B, and 17 Interface Symbology Suffix UPC a UPC E Connecting the Scanner with USB IBM SurePos USB PC or Macintosh Keyboard USB HID Connecting the Scanner with Serial Wedge USB Com Port Emulation Default = P1 Both P1 and P2 IT5600/IT5800 User’s Guide Terminal Interfaces Terminal ID Supported Terminals Terminal Models Terminal ID USB Hidpos Keyboard Country Keyboard Style Keyboard Modifiers IT5600/IT5800 User’s Guide Connecting the Scanner with RS-232 Serial Port RS-232 Baud Rate RS-232 Word Length Data Bits, Stop Bits, and Parity RS-232 Handshaking Wand Emulation Connection Wand Emulation Transmission Rate Wand Emulation Polarity Wand Emulation Wand Emulation IdleData Block Size Delay Between Blocks Overall Checksum Output Good Read IndicatorsBeeper Volume Good Read Beeper Good Read Beeper Duration Good Read LED Good ReadNumber of Beeps Good Read Trigger Modes Good Read DelayUser-Specified Good Read Delay Manual/Serial Trigger Automatic Trigger Read Time-Out Reread Delay Presentation ModeHands Free Time-Out User-Specified Reread Delay Aimer Beam Delay Aimer Beam option only Aimer Mode Aimer Beam option onlyUser-Specified Aimer Beam Delay Aimer Beam Time-Out Aimer Beam option only Centering Window IT5600/IT5800 User’s Guide Output Sequence Overview Output Sequence Editor Require Output SequenceOutput Sequence Example SEQBLK62999941FF6A999942FF69999943FF SEQBLK62001141FF6A001242FF69001143FF Multiple Symbols No Read Video Reverse Data Editing Prefix/Suffix OverviewPoints to Keep In Mind Scan the Add Prefix or Add Suffix symbol To Add a Prefix or SuffixScan Add Suffix To Clear One or All Prefixes or Suffixes To Add a Carriage Return Suffix to all SymbologiesScan the Clear One Prefix or Clear One Suffix symbol Prefix Selections Intercharacter, Interfunction, and Intermessage Delays Suffix SelectionsFunction Code Transmit Intercharacter Delay User Specified Intercharacter Delay Interfunction Delay Intermessage Delay Data Format Editor Introduction Scan the Enter Data Format symbol Primary/Alternate FormatData Formatting To Add a Data Format Other Programming Selections Data Format Editor CommandsEditor Commands Clear One Data Format Move Commands Data Format Editor Data Formatter Alternate Data Formats IT5600/IT5800 User’s Guide Secondary Interface Enabling the Secondary Interface Secondary RS-232 Connection Secondary Code 39 Wand Emulation Secondary Laser Emulation Laser Emulation Transmission Rate Secondary Trigger Mode Laser Emulation PolarityLaser Emulation Idle Hands Free Time-Out IT5600/IT5800 User’s Guide Symbologies All SymbologiesIntroduction Message Length Codabar Codabar Start/Stop CharactersCodabar Check Character Codabar Concatenation Codabar Code Codabar Message LengthCode 39 Start/Stop Characters Code 39 Check Character Code 39 Message Length Code 39 Append Code 32 Pharmaceutical Paraf Full Ascii Interleaved 2 Code 39 CodeCheck Digit Interleaved 2 of 5 Message Length Code 93 Message Length Code 93 Code Code 2 Iata Code 2Code 2 of 5 Message Length Matrix 2 Iata Code 2 of 5 Message Length Matrix 2 of 5 Message Length Check Digits Required Code 11 Message Length Isbt 128 Concatenation Code 128 Message LengthCode 128 Code Telepen Code 128 Function Code TransmitTelepen Output Telepen Message Length UPC a Check DigitUPC a Number System IT5600/IT5800 User’s Guide UPC a Addenda Required UPC aUPC a Addenda UPC a Addenda Separator UPC-A/EAN-13 with Extended Coupon Code UPC E0 and UPC E1 UPC E0 and UPC E1 Addenda Required UPC EUPC E0 and UPC E1 Expand UPC E0 and UPC E1 Addenda Separator UPC E0 Check Digit UPC E0 Number SystemUPC E0 Addenda EAN/JAN 13 Check Digit EAN/JAN 13 Addenda EAN/JAN 13 Addenda Separator EAN/JANEAN/JAN 13 Addenda Required Isbn Translate EAN/JAN 8 Check Digit EAN/JAN 8 Addenda EAN/JAN 8 Addenda Required EAN/JAN 8 Addenda Separator MSI MSI Check CharacterMSI Message Length Plessey Code RSS-14Plessey Message Length RSS Limited RSS Expanded Eanucc Emulation RSS Expanded Message Length China Post Code China Post Message Length Korea Post Code Korea Post Message Length PosiCode PosiCode a and BPosiCode Message Length Trioptic Code Codablock FCodablock F Message Length Code 16K Code 16K Message Length Code 49 Message Length IT5600/IT5800 User’s Guide Interface Keys Keyboard Function RelationshipsFunction Code HEX/ASCII Value Full Ascii Ctrl + Country Codes Compatibles Telex, Harris Supported Interface KeysIBM AT/XT PS/2 Compatibles IBM XTs IBM, DDC, Memorex Supported Keys Memorex Telex SYN PF1 ETB PF2 Can PF3 PF4 SUB PF5 ESC PF6 PF7 PF8 PF9 Esprit 200 Ansi Ascii HEX Apple Mac/iMac Show Software Revision To Add a Test Code I.D. Prefix to All SymbologiesUtilities Show Data Format Temporary Visual Menu 2003 Configuration Visual Menu 2003 Introduction Installing Visual Menu 2003 from the WebVisual Menu Visual Menu 2003 Operations IT5600/IT5800 User’s Guide Serial Programming Commands Menu Command SyntaxConventions Query Commands Concatenation of Multiple CommandsResponses Examples of Query Commands Trigger Commands ActivateSYN T CR DeactivateSYN U CR Menu Commands Setting Serial Selection Command TERMID64 Output Selections BEPLVL3 BEPBIP0 Prefix/Suffix Selections Data Formatter Selections Selections Symbologies C39SSX1 C39ASC0 C39ASC1 C11DFT UPAENA0 UPAENA1 EAN/JAN MSIENA0 MSIENA1 CPCMIN## IT5600/IT5800 User’s Guide Product Specifications IT5600 Product SpecificationsParameter Specification IT5600 Depth of Field IT5800 Product Specifications IT5800 Depth of Field Min. Bar Max Min. Far Field Width Near Field Standard CompatibleBar Image Pinouts Standard Cable Standard Cable Serial Output Standard Cable Cable Pinouts Standard IT5600/IT5800 User’s Guide Cleaning the Scanner’s Window MaintenanceMaintenance Inspecting Cords and Connectors Replacing the Interface Cable To Replace the IT5600 Interface Cable Troubleshooting To Replace the IT5800 Interface Cable Is the bar code displayed but not entered? Product Service and Repair Customer Support Technical Assistance Limited WarrantyOnline Product Service and Repair Assistance Online Technical Assistance IT5600/IT5800 User’s Guide IT5600/IT5800 User’s Guide Hex Symbology Code Symbology ChartSymbology Code Appendix a Ascii Conversion Chart Code Dec Hex CharHex Char Dec IT5600/IT5800 User’s Guide Code Page Mapping of Printed Bar Codes CP ISO646Page Page Interleaved 2 Code Codabar Programming Chart UG Rev C 6/05