B. Vent Components Diagrams continued | Heat & Glo LifeStyle RED40

B. Vent Components Diagrams (continued)

13-5/8 IN.

346 mm

12-1/2 IN.

318 mm

20-3/4 IN.

527 mm

PVI-SLP

Power Vent Inline

Optional Wire Harness

DESCRIPTION	PART NUMBER
10 ft. PV Wire Harness	PVI-WH10
20 ft. PV Wire Harness	PVI-WH20
40 ft. PV Wire Harness	PVI-WH40
60 ft. PV Wire Harness	PVI-WH60
80 ft. PV Wire Harness	PVI-WH80
100 ft. PV Wire Harness	PVI-WH100

Note: Wire harnesses required to power the PVI-SLP connect to the appliance and are ordered separately from PVI-SLP. Contact your dealer to order.

16 IN.

406 mm

4-1/2 IN.

114 mm

9-3/16 IN.

(233 mm)

15IN.

(381 mm)

13-5/8

(346 mm)

16-11/16 IN.

424 mm

16-11/16 IN.

(424 mm)

12-1/2 IN. (318 mm)

SLP-LPC

SLP Low Proﬁle Cap

Heat & Glo • RED40, RED40ST • 2155-900 Rev. o • 7/12	69

Page 69

Image 69

Heat & Glo LifeStyle RED40ST B. Vent Components Diagrams continued, Optional Wire Harness, Description, Part Number

Contents

NOTICE Models RED40 RED40ST•What to do if you smell gas Owner’s Manual Homeowner Reference Information A. Congratulations Safety Alert Key Table of ContentsInstaller Guide 3 Maintenance and Service 15 Troubleshooting 14 Appliance Setup = Contains updated information 13 Finishing LIMITED LIFETIME WARRANTY B. Limited Lifetime WarrantyWARRANTY COVERAGE WARRANTY PERIOD WARRANTY CONDITIONS B. Limited Lifetime Warranty continuedWARRANTY EXCLUSIONS This warranty is void if 1 Listing and Code Approvals D. High Altitude InstallationsA. Appliance Certiﬁcation B. Glass Speciﬁcations Installation of Carbon Monoxide Detectors 2 Operating Instructions User Guide A. Gas Fireplace SafetyB. Your Fireplace C. Clear Space D. Decorative Doors and Fronts E. Fixed Glass AssemblyG. Before Lighting Fireplace erate ﬁreplace with ﬁxed glass assembly removed Final inspection by H. Lighting Instructions IPIFOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS IPI I. After Fireplace is Lit J.Frequently Asked QuestionsInitial Break-inProcedure •Some people may be sensitive to smoke and odors A. Maintenance Tasks-Homeowner 3 Maintenance and ServiceGlass Cleaning Remote Control Gasket Seal and Glass Assembly Inspection B.Maintenance Tasks-QualiﬁedService TechnicianVenting Firebox A. Typical Appliance System Getting StartedInstaller Guide Figure 4.1 Typical System B. Design and Installation Considerations C.Tools and Supplies NeededD. Inspect Appliance and Components A. Selecting Appliance Location 5 Framing and Clearances 1/2 IN 1/2 IN. CFigure 5.2 Appliance Locations RED40ST C. Clearances B. Constructing the Appliance Chase MINIMUM FRAMING DIMENSIONS Dimensions of Non-Combustibles D. Mantel and Wall ProjectionsCombustible Mantels Non-CombustibleMantels A. Vent Termination Minimum Clearances 6 Termination LocationsRoof Pitch H Min. Ft = AREA WHERE TERMINAL IS NOT PERMITTED Covered Alcove ApplicationsV= VENT TERMINAL X = AIR SUPPLY INLET E. Vent Diagrams 7 Vent Information and DiagramsA. Approved Pipe B. Vent Table Key Venting with 1 elbow Top Vent - Horizontal TerminationV1 Minimum H1 Maximum Venting with 2 elbows 1. Top Vent - Horizontal Termination - continuedINSTALLED HORIZONTALLY H1 + H2 Maximum Venting with 3 elbows 1. Top Vent - Horizontal Terminationcontinued H2 V2 H1 V1 Top Vent - Vertical Termination No Elbows V = 3 ft Min. 1m, 50 ft. Max. 15.2 mExhaust restrictor Instructions V2 H1 V1 Top Vent - Vertical Termination Venting with 3 elbows DIRECT VENT WITH 5 in. / 8 in. DIAMETER DVP PIPE A. Pipe Clearances to Combustibles 8 Vent Clearances and FramingB. Wall Penetration Framing Between ceiling ﬁrestops C. Install the Ceiling Firestop D. Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation A. Appliance Preparation 9 Appliance Preparation Setting the Fireplace into the Framing B. Securing and Leveling the ApplianceWARNING! Risk of Fire! Prevent contact with •Sagging or loose insulation C. Active Convection Technology A. Assemble Vent Sections 10 Installing Vent Pipe DVP Pipe B. Assemble Slip Sections C. Secure The Vent SectionsPilot hole D. Disassemble Vent Sections E. Install Decorative Ceiling Components G. Assemble and Install Storm Collar F. Install Metal Roof FlashingCAULK CAUTION! Risk of Cuts, Abrasions or Flying Debris H. Install Vertical Termination Cap Figure 10.20 Venting Through the Wall J. Install Horizontal Termination Cap 11 Gas Information A. Fuel ConversionB. Gas Pressure •Ensure adequate ventilation C. Gas Connection B. IntelliFire Ignition System Wiring A. Wiring RequirementsC. Optional Accessories Requirements 12 Electrical Information REMOTE RECEIVER Optional Remote Control Receiver Location D. Optional LED Lighting Circuit SWITCH TRIPPEDCOLOR PRODUCED F. Junction Box Installation E. Electrical Service and RepairG. Active Convection Blower Replacement KNOCKOUT FAN MOUNT FASTENER SIDE BURNER SCREW BLOWER TAB ON MOUNTING PLATE SLOT ON BLOWER HOUSINGFigure 12.17. Remove Mounting Plate Figure 12.18. Removed Mounting Plate A. Splatter Guard 13 FinishingB. Framing and Finishing Instructions Finishing Instructions Finishing Around Opening with Gypsum Wallboard Finish and Sealing JointsPainting Figure 13.1 Finishing Details Dimensions of Combustibles C. Mantel and Wall Projections D. Facing Material Figure 13.5 Framing and Framing Materials-RED40Figure 13.6 Framing and Framing Materials-RED40ST Non-CombustibleFinish Materials 0 - 1 inch thickness-OverlapFit MethodFigure 13.7 Overlap Fit Method Figure 13.9 Inside Fit Method 0 Inches to 4 Inches Thick Inside Fit Method42-3/4IN 13-1/8IN ASSEMBLY E. Mesh FrontsMESH FRAME ASSEMBLY Figure 13.11. Mesh Front Installation A. Remove Fixed Glass Assembly 14 Appliance SetupC. Clean the Appliance D. Accessories I. Install the Mesh H. Fixed Glass AssemblyJ. Air Shutter Setting Removing Fixed Glass Assembly A. IntelliFire Ignition System 15 TroubleshootingSymptom Possible Cause IntelliFire Ignition System - continued 16 Reference Materials A. Appliance Dimension Diagram M N O P Figure 16.2 Appliance Dimensions RED40STT R Q S A F G B. Vent Components Diagrams Figure 16.2 DVP vent componentsDVP-AS2 DVP-TRAP1 B. Vent Components Diagrams continuedDVP-TRAP2 DVP-TRAPK1 31 in 13 in 8-1/8in206 mm 330 mm Optional Wire Harness DESCRIPTIONPART NUMBER RED40 C. Service Partsat Depot Stocked 40 in Landscape See-ThruDV Fireplace RED40ST Service Parts List #13 Control Assembly#14 Valve Assembly RED40,RED40ST RED40, RED40ST Service PartsStocked    15.3 #15 Base Pan No Lights with Media15.1 15.2 15.1 15.215.3 15.4 Stocked at Depot #16 Base Pan With Lights and Media16.3 16.1 16.3 16.216.1 16.4 Porcelain or No refractory #17 Base Pan No Lights or Media withRED40-NNNNo lights, No Rock, No Refractory RED40-NNPNo lights, No Rock, Porcelain RED40ST-NNNNo lights, No Rock, No Refractory Stocked at DepotRED40ST-NNPNo lights, No Rock, Porcelain RED40ST-NNGNo lights, No Rock, Granite #20 Porcelain --No Media #19 Granite --No Media#21 Granite --With Media #22 Porcelain --With Media RED40ST NOTES D. Contact Information