Appliance Setup, D. Accessories | Heat & Glo LifeStyle RED40

14 Appliance Setup

A. Remove Fixed Glass Assembly

See Section 14.H.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the ﬁrebox. Verify all components are with the ﬁreplace.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the ﬁrebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Install approved accessories per in- structions included with accessories. Contact your dealer for a list of approved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional acces- sories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

E. Rock Media Instructions

Arock media kit is available for use with the RED40 and RED40ST models. Install rock media per instructions in- cluded with kit.

F. Porcelain Instructions

A Porcelain Kit is available for use with the RED40 and RED40ST models. Install Porcelain per instructions in-

cluded with kit.

G. Granite Instructions

A Granite Kit is available for use with the RED40 and RED40ST models Install Granite per instructions includ- ed with kit.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. o • 7/12	59

Image 59

Heat & Glo LifeStyle RED40ST Appliance Setup, A. Remove Fixed Glass Assembly, B. Remove the Shipping Materials

Contents

Owner’s Manual Models RED40 RED40STNOTICE •What to do if you smell gas Homeowner Reference Information A. Congratulations 3 Maintenance and Service Table of ContentsSafety Alert Key Installer Guide 13 Finishing 14 Appliance Setup15 Troubleshooting  = Contains updated information WARRANTY PERIOD B. Limited Lifetime WarrantyLIMITED LIFETIME WARRANTY WARRANTY COVERAGE This warranty is void if B. Limited Lifetime Warranty continuedWARRANTY CONDITIONS WARRANTY EXCLUSIONS B. Glass Speciﬁcations D. High Altitude Installations1 Listing and Code Approvals A. Appliance Certiﬁcation Installation of Carbon Monoxide Detectors C. Clear Space A. Gas Fireplace Safety2 Operating Instructions User Guide B. Your Fireplace erate ﬁreplace with ﬁxed glass assembly removed E. Fixed Glass AssemblyD. Decorative Doors and Fronts G. Before Lighting Fireplace LIGHTING INSTRUCTIONS IPI H. Lighting Instructions IPIFinal inspection by FOR YOUR SAFETY READ BEFORE LIGHTING •Some people may be sensitive to smoke and odors J.Frequently Asked QuestionsI. After Fireplace is Lit Initial Break-inProcedure Remote Control 3 Maintenance and ServiceA. Maintenance Tasks-Homeowner Glass Cleaning Firebox B.Maintenance Tasks-QualiﬁedService TechnicianGasket Seal and Glass Assembly Inspection Venting Figure 4.1 Typical System Getting StartedA. Typical Appliance System Installer Guide D. Inspect Appliance and Components B. Design and Installation ConsiderationsC.Tools and Supplies Needed A. Selecting Appliance Location 5 Framing and Clearances Figure 5.2 Appliance Locations RED40ST 1/2 IN1/2 IN. C C. Clearances B. Constructing the Appliance Chase MINIMUM FRAMING DIMENSIONS Non-CombustibleMantels D. Mantel and Wall ProjectionsDimensions of Non-Combustibles Combustible Mantels H Min. Ft 6 Termination LocationsA. Vent Termination Minimum Clearances Roof Pitch V= VENT TERMINAL X = AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTEDCovered Alcove Applications B. Vent Table Key 7 Vent Information and DiagramsE. Vent Diagrams A. Approved Pipe H1 Maximum Top Vent - Horizontal TerminationVenting with 1 elbow V1 Minimum H1 + H2 Maximum 1. Top Vent - Horizontal Termination - continuedVenting with 2 elbows INSTALLED HORIZONTALLY H2 V2 H1 V1 1. Top Vent - Horizontal TerminationVenting with 3 elbows continued Exhaust restrictor Instructions Top Vent - Vertical Termination No ElbowsV = 3 ft Min. 1m, 50 ft. Max. 15.2 m V2 H1 V1 Top Vent - Vertical Termination H1 + H2 Maximum DIRECT VENT WITH 5 in. / 8 in. DIAMETER DVP PIPE Between ceiling ﬁrestops 8 Vent Clearances and FramingA. Pipe Clearances to Combustibles B. Wall Penetration Framing C. Install the Ceiling Firestop Vaulted Ceiling Installation D. Install Attic Insulation ShieldFlat Ceiling Installation A. Appliance Preparation 9 Appliance Preparation •Sagging or loose insulation B. Securing and Leveling the ApplianceSetting the Fireplace into the Framing WARNING! Risk of Fire! Prevent contact with C. Active Convection Technology A. Assemble Vent Sections 10 Installing Vent Pipe DVP Pipe Pilot hole B. Assemble Slip SectionsC. Secure The Vent Sections D. Disassemble Vent Sections E. Install Decorative Ceiling Components CAUTION! Risk of Cuts, Abrasions or Flying Debris F. Install Metal Roof FlashingG. Assemble and Install Storm Collar CAULK H. Install Vertical Termination Cap Figure 10.20 Venting Through the Wall J. Install Horizontal Termination Cap B. Gas Pressure 11 Gas InformationA. Fuel Conversion •Ensure adequate ventilation C. Gas Connection 12 Electrical Information A. Wiring RequirementsB. IntelliFire Ignition System Wiring C. Optional Accessories Requirements REMOTE RECEIVER Optional Remote Control Receiver Location COLOR PRODUCED D. Optional LED Lighting CircuitSWITCH TRIPPED KNOCKOUT E. Electrical Service and RepairF. Junction Box Installation G. Active Convection Blower Replacement FAN MOUNT FASTENER SIDE BURNER SCREW Figure 12.18. Removed Mounting Plate SLOT ON BLOWER HOUSINGBLOWER TAB ON MOUNTING PLATE Figure 12.17. Remove Mounting Plate Finishing Instructions 13 FinishingA. Splatter Guard B. Framing and Finishing Instructions Figure 13.1 Finishing Details Finish and Sealing JointsFinishing Around Opening with Gypsum Wallboard Painting Dimensions of Combustibles C. Mantel and Wall Projections Figure 13.6 Framing and Framing Materials-RED40ST D. Facing MaterialFigure 13.5 Framing and Framing Materials-RED40 Figure 13.7 Overlap Fit Method Non-CombustibleFinish Materials0 - 1 inch thickness-OverlapFit Method 13-1/8IN 0 Inches to 4 Inches Thick Inside Fit MethodFigure 13.9 Inside Fit Method 42-3/4IN Figure 13.11. Mesh Front Installation E. Mesh FrontsASSEMBLY MESH FRAME ASSEMBLY D. Accessories 14 Appliance SetupA. Remove Fixed Glass Assembly C. Clean the Appliance Removing Fixed Glass Assembly H. Fixed Glass AssemblyI. Install the Mesh J. Air Shutter Setting Possible Cause 15 TroubleshootingA. IntelliFire Ignition System Symptom IntelliFire Ignition System - continued 16 Reference Materials A. Appliance Dimension Diagram A F G Figure 16.2 Appliance Dimensions RED40STM N O P T R Q S DVP-AS2 B. Vent Components DiagramsFigure 16.2 DVP vent components DVP-TRAPK1 B. Vent Components Diagrams continuedDVP-TRAP1 DVP-TRAP2 31 in 330 mm 8-1/8in13 in 206 mm PART NUMBER Optional Wire HarnessDESCRIPTION Stocked C. Service PartsRED40 at Depot 40 in Landscape See-ThruDV Fireplace RED40ST RED40,RED40ST #13 Control AssemblyService Parts List #14 Valve Assembly    Service PartsRED40, RED40ST Stocked 15.2 #15 Base Pan No Lights with Media15.3 15.1 15.4 15.215.1 15.3 16.1 #16 Base Pan With Lights and MediaStocked at Depot 16.3 16.4 16.216.3 16.1 RED40-NNPNo lights, No Rock, Porcelain #17 Base Pan No Lights or Media withPorcelain or No refractory RED40-NNNNo lights, No Rock, No Refractory RED40ST-NNGNo lights, No Rock, Granite Stocked at DepotRED40ST-NNNNo lights, No Rock, No Refractory RED40ST-NNPNo lights, No Rock, Porcelain #22 Porcelain --With Media #19 Granite --No Media#20 Porcelain --No Media #21 Granite --With Media #21 Granite --With Media NOTES D. Contact Information