SLP-45 45 Elbow, SLP90- 90 Elbow | Heat & Glo LifeStyle XLR-PB-CE

B. Vent Components Diagrams (continued)

	16,5 cm
16,5 cm	16,5 cm
	16,5 cm
22,2 cm	23,5 cm
	23,5 cm
	15,2 cm
16,8 cm
SLP-45 - 45° Elbow	16,8 cm
SLP-45 - 45° Elbow
	25,1 cm
	SLP90- 90° Elbow

				Effective Height/Length
				Effective Height/Length

				Pipe	cm	mm
Effective				SLP4	10,2	102
Height/
Height/				SLP6	15,2	152
Length
Length				SLP12	30,5	305
				SLP12	30,5	305
				SLP24	61	610

				SLP36	91,4	914
				SLP36	91,4	914

				SLP48	121,9	1219

			SLP-PIPE	SLP6A	5 - 15	51-152
			SLP-PIPE	SLP12A	5 - 30	51-305
				SLP12A	5 - 30	51-305

66,0 cm

DVP-HSM-B

Extended Heat Shield

SLP-HVS	SLP-FS	SLP-WS
Horizontal Pipe	Ceiling Firestop	Wall Shield Firestop
Support

Figure 17.3 SLP Series Vent Components

Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12

59

Image 59

Heat & Glo LifeStyle XLR-PB-CE, XLR-N-CE SLP-45 45 Elbow, SLP90- 90 Elbow, Extended Heat Shield, Ceiling Firestop, Support

Contents

What to do if you smell gas EC-87/09/058 Homeowner Reference Information Congratulations User Guide Table of Contents Reference Materials Appliance SetupTroubleshooting Component Access Limited Lifetime Warranty Limited Lifetime Warranty Hearth & Home Technologies Inc Warranty Conditions Limited Lifetime Warranty Listing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Decorative Doors and Fronts Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear Space Control Module Operation  Nine Hour Safety Shutdown FeatureModule Reset Switch AGE 110/120 VAC or 220/240 Lighting Instructions IPIFinal inspection by After Fireplace is Lit Battery Tray/Battery InstallationFrequently Asked Questions Initial Break-in Procedure Decorative Doors Maintenance and ServiceMaintenance Tasks-Homeowner Glass Cleaning Control Compartment and Firebox Top Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection Firebox Typical Appliance System Getting Started Inspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Selecting Appliance Location Framing and Clearances Constructing the Appliance Chase Clearances Minimum Framing Dimensions Mantel Leg Combustible/Non-Combustible Mantel and Wall ProjectionsMantels Combustible/Non-Combustible Vent Termination Minimum Clearances Termination Locations Covered Alcove Applications Vent Information and Diagrams Minimum Maximum Top Vent Horizontal Termination Venting with 1 elbow Top Vent Horizontal Termination Venting with 2 elbows Exhaust restrictor Instructions Top Vent Vertical Termination No Elbows V1 = 13,4 m V1 Minimum Maximum V1 + V2 Minimum Top Vent Vertical Termination Venting with 2 elbows V1 Minimum H1 + H2 Maximum V1 + V2 Minimum Top Vent Vertical Termination Venting with 3 elbows Min Max Top Vent Vertical Termination Venting with 4 elbows Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Pipe SLP Install the Ceiling Firestop Vaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Top Vent Appliance Preparation Proper Positioning, Leveling And Securing of an Securing and Leveling the Appliance Assemble Vent Sections Installing Vent Pipe SLP Pipe Secure The Vent Sections Assemble Slip Sections Disassemble Vent Sections Install Decorative Ceiling Components Assemble and Install Storm Collar Install Metal Roof Flashing Heat Shield Requirements for Horizontal Termination Install Vertical Termination CapInstall Decorative Wall Components 17 Venting through the wall Install Horizontal Termination Cap Gas Pressure Requirements Gas Connection Access Through the Valve AssemblyGas Information Optional Remote Control Receiver and Battery Pack Location Wiring RequirementsIntelliFire Plus Ignition System Wiring Optional Accessories Requirements Junction Cord Information Electrical Service and Repair Blower Finishing Instructions Non-Combustible Materials SpecificationFinishing Framing and Finishing Instructions FACTORY-INST Alled Wallboard Joint-Crack Prevention and Repair Finish and Sealing JointsFinishing Around Opening with Gypsum Wallboard Painting Overlap Fit Method Tonic or Martini Decorative Front Facing Material Non-Combustible Finish Material 0-10 cm Thick Decorative Fronts Dimensions of Tonic Decorative Front Appliance Setup Media Options Air Shutter SettingAir Shutter Settings IntelliFire Plus Ignition System TroubleshootingSymptom Possible Cause Corrective Action Ues to spark, and main Component Access Valve Assembly Gasket Pilot Assembly Replacement Gas Valve Replacement Reference Materials Appliance Dimension Diagram Vent Components Diagrams Ceiling Firestop SLP-45 45 ElbowSLP90- 90 Elbow Extended Heat Shield Black 30,5 cm 17,8 cm 39,4 cm SnorkelSupport Box-Black Adapter SLP-HRC-SS SLP-HRC-ZC-SS Horizontal Termination CAP Landscape DV Appliance Service Parts #14 Valve Assembly XLR-N-CE, XLR-PB-CE Service Parts List Contact Information