Hitachi HTS541640J9SA00, HTS541680J9SA00, HTS541616J9SA00, HTS541660J9SA00 manual Read DMAC8h/C9h

Travelstar 5K160 (SATA) Hard Disk Drive Specification

14.13Read DMA(C8h/C9h)

Command Block Output Registers																		Command Block Input Registers
Register				7		6			5		4			3	2	1	0	Register					7	6			5			4		3	2		1		0
Data				-	-			-			-		-		-	-	-	Data					-	-		-		-			-		-		-		-
Feature				-	-			-			-		-		-	-	-	Error							...See Below...
Sector Count				V		V			V	V				V	V	V	V	Sector Count					V	V			V		V			V	V		V		V
LBA Low				V		V			V	V				V	V	V V		LBA Low					V	V		V V V V								V		V
LBA Mid				V		V			V	V				V	V	V	V	LBA Mid					V	V			V			V		V V		V		V
LBA High				V		V			V	V				V	V	V	V	LBA High					V	V			V			V		V	V	V		V
Device				-		L		-			-			H	H	H	H	Device					-	-		-		-				H	H		H		H
Command				1		1			0	0				1	0	0	R	Status							...See Below...
			Error Register																		Status Register
7	6	5	4	3			2					1				0		7	6	5	4	3			2						1				0
CRC	UNC	0	IDN	0			ABT					T0N				AM		BSY	RDY	DF	DSC	DRQ				COR						IDX			ERR
																N
V	V	0	V	0					V			0				0		0	V	0	V	-			0						0				V

Figure 46 Read DMA Command (C8h/C9h)

The Read DMA command reads one or more sectors of data from disk media, then transfers the data from the device to the host.

The sectors are transferred through the Data Register 16 bits at a time.

The host initializes a slave-DMA channel prior to issuing the command. The data transfers are qualified by DMARQ and are performed by the slave-DMA channel. The device issues only one interrupt per command to indicate that data transfer has terminated and status is available.

If an uncorrectable error occurs, the read will be terminated at the failing sector.

Output Parameters To The Device

Sector Count	The number of continuous sectors to be transferred. If zero is specified, then 256 sectors
LBA Low	will be transferred.
	The sector number of the first sector to be transferred. (L=0)
LBA High/Mid	In LBA mode, this register specifies LBA address bits 0 - 7 to be transferred. (L=1)
	The cylinder number of the first sector to be transferred. (L=0)
	In LBA mode, this register specifies LBA address bits 8 - 15 (Mid) 16 - 23 (High) to be
H	transferred. (L=1)
	The head number of the first sector to be transferred. (L=0)
R	In LBA mode, this register specifies LBA bits 24-27 to be transferred. (L=1)
	The retry bit, but this bit is ignored.
Input Parameters From The Device
Sector Count	The number of requested sectors not transferred. This will be zero, unless an
LBA Low	unrecoverable error occurs.
	The sector number of the last transferred sector. (L=0)
LBA High/Mid	In LBA mode, this register contains current LBA bits 0 - 7. (L=1)
	The cylinder number of the last transferred sector. (L=0)
	In LBA mode, this register contains current LBA bits 8 - 15 (Mid), 16 - 23 (High).
H	(L=1)
	The head number of the sector to be transferred. (L=0)
	In LBA mode, this register contains current LBA bits 24 - 27. (L=1)

95/167