Travelstar 5K160 (SATA) Hard Disk Drive Specification
|
|
|
|
| enabled |
|
|
| 3 | (=x) | 1=Advanced Power Management Feature Set enabled |
|
|
| 2 | (=0) | 1=CFA Feature Set supported |
|
|
| 1 | (=0) | 1=READ/WRITE DMA QUEUED command |
|
|
|
|
| supported |
|
|
| 0 | (=1) | 1=DOWNLOAD MICROCODE command supported |
87 | 4163H |
| Command set/feature enabled | ||
|
|
| 15 | (=0) | Always |
|
|
| 14 | (=1) | Always |
|
|
| 13 | (=0) | 1=IDLE IMMEDIATE with UNLOAD FEATURE |
|
|
|
|
| supported |
|
|
| 12- 11 | (=0) | Reserved |
|
|
| 10 | (=0) | 1=URG bit supported for WRITE STREAM DMA |
|
|
|
|
| EXT and WRITE STREAM EXT |
|
|
| 9 | (=0) | 1=URG bit supported for READ STREAM DMA |
|
|
|
|
| EXT and READ STREAM EXT |
|
|
| 8 | (=1) | 1=64 bit World wide name supported |
|
|
| 7 | (=0) | 1=WRITE DMA QUEUED FUA EXT command |
|
|
|
|
| supported |
|
|
| 6 | (=1) | 1=WRITE DMA FUA EXT and WRITE MULTIPLE |
|
|
|
|
| FUA EXT command supported |
|
|
| 5 | (=1) | 1=General Purpose Logging feature set supported |
|
|
| 4- 2 | (=0) | Reserved |
|
|
| 1 | (=1) | 1=SMART |
|
|
| 0 | (=1) | 1=SMART error logging supported |
88 | xx3FH |
| Ultra DMA Transfer mode (mode 5 supported) | ||
|
|
| 15 | (=0) | Reserved |
|
|
| 14 | (=0) | 1=UltraDMA mode 6 is selected |
|
|
| 13 | (=x) | 1=UltraDMA mode 5 is selected |
|
|
| 12 | (=x) | 1=UltraDMA mode 4 is selected |
|
|
| 11 | (=x) | 1=UltraDMA mode 3 is selected |
|
|
| 10 | (=x) | 1=UltraDMA mode 2 is selected |
|
|
| 9 | (=x) | 1=UltraDMA mode 1 is selected |
|
|
| 8 | (=x) | 1=UltraDMA mode 0 is selected |
|
|
| 7 | (=0) | Reserved |
|
|
| 6 | (=0) | 1=UltraDMA mode 6 is supported |
|
|
| **5 | (=1) | 1=UltraDMA mode 5 is supported |
|
|
| **4 | (=1) | 1=UltraDMA mode 4 is supported |
|
|
| **3 | (=1) | 1=UltraDMA mode 3 is supported |
|
|
| **2 | (=1) | 1=UltraDMA mode 2 is supported |
|
|
| **1 | (=1) | 1=UltraDMA mode 1 is supported |
|
|
| 0 | (=1) | 1=UltraDMA mode 0 is supported |
Note.1 The ‘*’ mark in ‘Content’ field indicates the use of those parameters that are vendor specific.
Note.2 The feature marked ‘**’ is able to be unsupported by the Device Configuration Overlay command.
Figure 38 Identify device information
89 | xxxxH |
| Time required for security erase unit completion |
|
|
| Time= value(xxxxh)*2 [minutes] |
90 | 0000H |
| Time required for Enhanced security erase completion |
|
|
| 0000 : Not supported |
91 | 40xxH |
| Current Advanced Power Management level |
|
| 88/167 |