Honeywell VM1 Power Meter, View UPS Battery Status

View UPS Battery StatusPower Meter

Start > Control Panel > Power Options > Power Schemes tab (Classic View)

Start > Control Panel > Performance and Maintenance> Power Options > Power Schemes tab (Category View)

On the Power Meter tab, battery #1 refers to the UPS battery.

Shows power status: external power or UPS battery and the total battery power remaining before a recharge is necessary.

5 - 19

Contents

Page Disclaimer Trademarks Patents Table of Contents Chapter 1 - Thor VM1 Agency Information Chapter 2 - Getting Started Chapter 3 - Hardware Overview Chapter 4 - Vehicle Mounting and Accessory Installation Chapter 5 - Software Chapter 6 - Wireless Network Connections Page Chapter 7 - Key Maps Chapter 8 - Specifications and Reference Material Chapter 9 - Customer Support Page Thor VM1 Agency Information FCC Part 15 Statement FCC 5GHz Statement EMC Directive Requirements Canada, Industry Canada (IC) Notices COFETEL ANATEL (Brazil) Vehicle Power Supply Connection Safety Statement Li-IonBattery RF Safety Notice Bluetooth Honeywell Scanning & Mobility Product Environmental Information CE Mark Dealer License - Republic of Singapore Page Getting Started Overview About this Guide Out of the Box Initial Setup for Thor VM1 Quick Mount Smart Dock Components Back View with Quick Mount Smart Dock Access Panels Backlights and Indicators Power Up Tapping the Touch Screen with a Stylus Setup Terminal Emulation Parameters Cleaning the Touch Screen Startup Help Hardware Overview System Hardware Power Uninterruptible Power Supply Safe Charging Temperature Range Charging Timeout Charging and Power Management Backup Battery Fuse Power Management Modes Full On Mode StandbyMode System Standby Wakeup Events Power Controls Power Switch Power Button Auto On Behavior Ignition Control External Connectors Page Antenna Connections External Antenna Connector Internal 802.11 Antenna Vehicle Remote Antenna Keyboard Options LED Functions SYS (System Status) LED UPS Status LED External Power Present External Power Not Present SSD (Solid State Drive) LED Connection LEDs WWAN LED Wi-FiLED Bluetooth LED Display Touch Screen Defroster Screen Blanking Display Backlight Control Vehicle Mounting and Accessory Installation Introduction Prepare for Vehicle Mounting Maintenance - Vehicle Mounted Devices Cleaning Place Thor VM1 in the Dock Dock I/O Pin Cover Padlock Laptop Security Cable Install RAM Mount Procedure - RAM Mount Assembly Step 1a – Attach RAM Ball to Vehicle Mounting Dimensions Step 1b – Mount RAM Clamp to Vehicle Step 1c – Attach RAM Plate to Vehicle and Attach RAM Ball Step 2 – Attach RAM Mount Ball to the Thor VM1 Quick Mount Smart Dock Step 3 – Attach Thor VM1 Assembly to RAM Mount Step 4 – Place the Thor VM1 into the Dock Install U Bracket Mount Mounting Positions Step 1 - Install U Bracket to Vehicle Step 2 - Remove RAM Ball Step 3 - Attach Adapter Bracket Connect Cables Connect Power Power Cable Cautions Power Cable Routing 12-48VDC Vehicles (10-60VDC Direct Connection) Vehicle 10-60VDCDirect Power Connection Page Ignition Control Wiring Diagram Auto-OnControl Wiring Diagram Manual Control Wiring Diagram 60-144VDC Vehicles (50-150VDC Power Supply, Screws on Side of Lid) Vehicle 50-150VDCPower Connection Page Page 60-144VDC Vehicles (50-150VDC Power Supply, Screws on Top of Lid) Page Page Page VX6 / VX7 Adapter Cable Connect to VX6 / VX7 Power Cable Thor VX8 / Thor VX9 Adapter Cable Connect to Thor VX8 / VX9 Power Cable Screen Blanking Cable Honeywell Screen Blanking Box Cable User-SuppliedCable Screen Blanking Box Screen Blanking with Switch External AC/DC Power Supply Connect External Power Supply Connect USB Host Connect USB Client Connect Serial Device Connect a Tethered Scanner Connect Headset Cable Adjust Headset / Microphone and Secure Cable Under Clothing Over Clothing Connect CANbus Cable Install Remote Antenna 802.11 Remote Mount Antenna Components and Mounting Diagram Typical Installation Mounting Instructions WAN Remote Mount Antenna GPS Remote Mount Antenna Apply Touch Screen Protective Film Disconnect UPS Battery Install SD Card Install SIM Card Replace Front Panel Page Replace UPS Battery Page Page Software Microsoft Windows Setup and Configuration Freefloat Link*One Wedge Freefloat Access*One TE (Optional) Control Panel Network IP MAC Address AutoOn Bluetooth Bluetooth Devices Discover Stop Button Bluetooth Device List Clear Button Bluetooth Device Menu Right-ClickMenu Options Bluetooth Device Properties Turn Off Bluetooth Options Page Reconnect Page Using Bluetooth Bluetooth Devices Display - Before Discovering Devices Initial Configuration Subsequent Use Bluetooth Indicators Bluetooth Bar Code Reader Setup Thor VM1 with Label Thor VM1 without Label Bluetooth Beep and LED Indications Bluetooth Printer Setup Easy Pairing and Auto-Reconnect Display Power Options Select a Power Scheme Power Schemes View UPS Battery Status Power Meter Configure Power Button Behavior Advanced Hibernate Enable Hibernation Screen Control Automatic Brightness Control Current Level Defroster Control Screen Rotation Sounds User Accounts Wi-Fi Bar Code Readers Touch Screen Calibration BIOS Thor VM1 Recovery DVD Upgrading the Thor VM1 Automatic Firmware Update Utility Configuration Cloning Utility (CCU) Configuration Cloning Utility GUI Menu Options File Open Close Save Page Shortcuts Modifying Settings Using the CCU Example 1: Import the current settings and save to a file Example 2: Modify settings on the current device and save to a file Example 3: Reset a device to system defaults Example 4: Clone settings to another device Configuration Cloning Utility Command Line Interface Example 1: Launch GUI Example 2: Import settings Example 3: Apply settings Page Page Wireless Network Connections Network Connections Control Panel Summit Wireless Network Configuration Important Notes Summit Client Utility Wireless Zero Config Utility To Switch Control to the Wireless Zero Config Utility To Switch Control to SCU Main Admin Login Page Profile Buttons Profile Parameters Page Status Diags Global Custom Parameter Option Global Parameters Page Logon Options Single Signon Pre-LogonConnection Sign-Onvs. Stored Credentials To Use Sign On Screen To Use Windows Username and Password Windows Certificate Store vs. Certs Path Configuring the Profile No Security WEP LEAP PEAP/MSCHAP Page PEAP/GTC Page WPA/LEAP EAP-FAST Page EAP-TLS Page WPA PSK Certificates Page Install a Root CA Certificate Generate a User Certificate Exporting a User Certificate Install a User Certificate Manually Initiate Certificate Installation OneClick Internet Page Using OneClick Internet Connection Management Menu Buttons Radio Button Statistics Button Update Button Help Button Settings Button Profile Parameters Network Network with SIM Card Select Connection Select Network CDMA Network History PIN Activate/Deactivate PIN Change PIN Info Firmware Activation on CDMA General Application Application Buttons SMS Folder New SMS Reply Forward Move SMS Delete Addresses Web Browser Email GPS System Requirements Supported Languages Installing or Upgrading OneClick Internet Installation Page OneClick Internet Connection Manager Page Information Buttons Key Maps 64-KeyQWERTY Keypad Key Map Page Page Page IBM Terminal Emulation Page Specifications and Reference Material Technical Specifications Dimensions Environmental Specifications Network Card Specifications Port and Connector Pinouts USB Y Cable D9 Male Connector USB Host Connector USB Client Connector Headset Adapter Cable D15 Female Connector Quick Connect Headset Connector CANbus Y Cable 9-PinJ1939 (Deutsch) Connectors Hat Encoding Page Page Customer Support Product Service and Repair Technical Assistance Limited Warranty