Manuals / Brands / Baby / Doll / HP / Baby / Doll

HP Doll c7000 Installing a power supply, Component installation

1 103

Download 103 pages, 4.54 Mb

4.Close the hinges, and tighten the thumbscrews to secure the rear cage.

Component installation

The following sections contain installation instructions for the individual enclosure components. All components must be installed and cabled before you power up the enclosure. There is no specific installation order requirement for the enclosure components.

Installing a power supply

See "Running the Insight Display installation steps (on page 65)" for information on the types of power configurations available and how to set them up.

If your HP BladeSystem c7000 Enclosure is equipped with a three-phase power configuration, six power supplies are required. Single-phase configurations can have fewer than six power supplies.

Install the power supplies based on the total number of supplies needed:

•Two power supplies: Bays 1 and 4

•Three power supplies: Bays 1, 2, and 4

•Four power supplies: Bays 1, 2, 4, and 5

•Five power supplies: Bays 1, 2, 3, 4, and 5

•Six power supplies: All bays

Install power supply blanks in any unused power supply bays.

Power supplies are installed in this manner to provide maximum flexibility for redundancy in three-phase configuration options.

CAUTION: Do not mix HP 2250W, HP 2400W High Efficiency, HP BL7000 2400W Platinum, or -48vDC power supplies in one enclosure. Install only one type of power supply in a single enclosure.

Installation 29

Contents

HP BladeSystem c7000 Enclosure Setup and Installation Guide Page Contents HP BladeSystem Insight Display Troubleshooting Support and other resources Regulatory compliance notices Documentation feedback Planning the installation Rack requirements The enclosure is compatible with the following racks: All HP 10000 and 10000G2 Series racks except the HP 10614 rack NOTE: •Telco racks Rack-freeenvironment requirements Warning, caution, and important messages CAUTION: Space and airflow requirements Temperature requirements Power requirements Grounding requirements Component and LED identification Power supply bay numbering Power supply LEDs Device bay numbering Full-heightdevice bay numbering Half-heightdevice bay numbering HP BladeSystem Insight Display components Location Discovery Services Enclosure rear components Fan bay numbering Fan LED Onboard Administrator components HP c7000 Onboard Administrator with KVM components Interconnect bay numbering Installation Page Page Rack-freeinstallation Rack installation Measuring with the rack template Installing the rack rails Installing the enclosure into the rack Page Installing the rear cage into the enclosure Installing a power supply Page Installing blades Installing a full-heightblade Page Page Removing a device bay shelf Creating a full-heightdevice bay blank Page Installing a half-heightblade Installing a device bay shelf Page Page Connecting locally to a server blade with video and USB devices Accessing a server blade with local KVM Accessing local media devices Installing fans Page Installing Onboard Administrator modules Attaching components to the HP c7000 Onboard Administrator with KVM Installing interconnect modules Page Mapping to interconnect ports Mapping half-heightblades Mapping full-heightblades Mapping BL2x220c Blades Mapping the BL680c G7 Blade Interconnect bay identification Bay-to-baycrosslinks Device bay crosslinks Interconnect bay crosslinks Removing interconnect bay dividers Installing interconnect bay dividers Cabling and powering up the enclosure Onboard Administrator cabling Enclosure link cabling Cabling a PC to the enclosure service port Cabling the network to the enclosure Single-phaseAC configuration Page 8.Open the snap clamps, and then insert each power cord inside each clamp Slide the power cord retention bracket until the bracket touches the enclosure PDU installation Page Three-phaseAC configuration HP BladeSystem Insight Display Page oNone Enabled—You Disabled—All Not Present _ and . is used to signal the end of the name Yes—Copy No—Continue 8.Verify all components are installed and cabled before continuing Navigating the Insight Display Health Summary screen Page Page Enclosure Settings screen Enclosure Info screen Blade and Port Info screen Turn Enclosure UID On/Off screen Page View User Note screen Chat Mode screen Troubleshooting Important safety information Symbols on equipment Warnings and cautions Power errors Cooling errors Location errors Configuration errors Device failure errors Page Support and other resources Réparation par le client (CSR) Riparazione da parte del cliente Reparaciones del propio cliente Reparo feito pelo cliente Page Page Page Regulatory compliance notices FCC rating label FCC Notice, Class A Equipment FCC Notice, Class B Equipment Modifications Cables Canadian notice (Avis Canadien) European Union regulatory notice Page Chinese notice Laser compliance Do not try to open the module enclosure. There are no •Allow only HP Authorized Service technicians to repair the unit Battery replacement notice Taiwan battery recycling notice Power cord statement for Japan Electrostatic discharge Acronyms and abbreviations CSA CSR ESD ICPM USB Documentation feedback Index