Manuals / Brands / Baby / Doll / HP / Baby / Doll

HP Doll c7000 Installing the enclosure into the rack

1 103

Download 103 pages, 4.54 Mb

3.Slide the front end of the rail to the rack front column. When fully seated, the rack rail will lock into place.

4.Repeat the procedure for the right rack rail.

Installing the enclosure into the rack

The empty enclosure with the rear cage installed weighs 58.6 kg (129 lb). When the enclosure is disassembled, the empty enclosure without the rear cage installed weighs 35.5 kg (78 lb). The empty rear cage weighs 23.2 kg (51 lb).

WARNING: Always use at least two people to lift an enclosure into the rack. If the enclosure is being loaded into the rack above chest level, a third person must assist with aligning the enclosure with the rails while the other two people support the weight of the enclosure.

To install the enclosure into the rack:

1.At the front of the rack, lift and align the enclosure guiding fins with the guiding groove in the rack rails.

IMPORTANT: Be sure that the guiding fins on the enclosure seat properly in the guiding groove on the rack rail.

Installation 26

Contents

HP BladeSystem c7000 Enclosure Setup and Installation Guide Page Contents HP BladeSystem Insight Display Troubleshooting Support and other resources Regulatory compliance notices Documentation feedback Planning the installation Rack requirements The enclosure is compatible with the following racks: All HP 10000 and 10000G2 Series racks except the HP 10614 rack NOTE: •Telco racks Rack-freeenvironment requirements Warning, caution, and important messages CAUTION: Space and airflow requirements Temperature requirements Power requirements Grounding requirements Component and LED identification Power supply bay numbering Power supply LEDs Device bay numbering Full-heightdevice bay numbering Half-heightdevice bay numbering HP BladeSystem Insight Display components Location Discovery Services Enclosure rear components Fan bay numbering Fan LED Onboard Administrator components HP c7000 Onboard Administrator with KVM components Interconnect bay numbering Installation Page Page Rack-freeinstallation Rack installation Measuring with the rack template Installing the rack rails Installing the enclosure into the rack Page Installing the rear cage into the enclosure Installing a power supply Page Installing blades Installing a full-heightblade Page Page Removing a device bay shelf Creating a full-heightdevice bay blank Page Installing a half-heightblade Installing a device bay shelf Page Page Connecting locally to a server blade with video and USB devices Accessing a server blade with local KVM Accessing local media devices Installing fans Page Installing Onboard Administrator modules Attaching components to the HP c7000 Onboard Administrator with KVM Installing interconnect modules Page Mapping to interconnect ports Mapping half-heightblades Mapping full-heightblades Mapping BL2x220c Blades Mapping the BL680c G7 Blade Interconnect bay identification Bay-to-baycrosslinks Device bay crosslinks Interconnect bay crosslinks Removing interconnect bay dividers Installing interconnect bay dividers Cabling and powering up the enclosure Onboard Administrator cabling Enclosure link cabling Cabling a PC to the enclosure service port Cabling the network to the enclosure Single-phaseAC configuration Page 8.Open the snap clamps, and then insert each power cord inside each clamp Slide the power cord retention bracket until the bracket touches the enclosure PDU installation Page Three-phaseAC configuration HP BladeSystem Insight Display Page oNone Enabled—You Disabled—All Not Present _ and . is used to signal the end of the name Yes—Copy No—Continue 8.Verify all components are installed and cabled before continuing Navigating the Insight Display Health Summary screen Page Page Enclosure Settings screen Enclosure Info screen Blade and Port Info screen Turn Enclosure UID On/Off screen Page View User Note screen Chat Mode screen Troubleshooting Important safety information Symbols on equipment Warnings and cautions Power errors Cooling errors Location errors Configuration errors Device failure errors Page Support and other resources Réparation par le client (CSR) Riparazione da parte del cliente Reparaciones del propio cliente Reparo feito pelo cliente Page Page Page Regulatory compliance notices FCC rating label FCC Notice, Class A Equipment FCC Notice, Class B Equipment Modifications Cables Canadian notice (Avis Canadien) European Union regulatory notice Page Chinese notice Laser compliance Do not try to open the module enclosure. There are no •Allow only HP Authorized Service technicians to repair the unit Battery replacement notice Taiwan battery recycling notice Power cord statement for Japan Electrostatic discharge Acronyms and abbreviations CSA CSR ESD ICPM USB Documentation feedback Index