Manuals / Brands / Baby / Doll / HP / Baby / Doll

HP Doll c7000 Three-phaseAC configuration, Running the Insight Display installation steps, 1.Connect the AC power cables to the AC power source

1 103

Download 103 pages, 4.54 Mb

Three-phase AC configuration

For a three-phase power configuration, the AC power cables are already attached to the enclosure. To cable the enclosure using a three-phase AC configuration:

1.Connect the AC power cables to the AC power source.

2.Turn on the AC circuit breakers that power the power cables installed in the enclosure.

When the enclosure powers up for the first time, it might take up to 5 minutes before all blades are initialized and recognized by the Onboard Administrator. The time it takes to complete initialization depends on the number of blades configured in the enclosure. For example, a full enclosure of 16 blades might take 5 minutes to power up, while an enclosure with fewer blades might take less time. Server blades are powered up incrementally, starting from device bay 1.

When first initialized, the Onboard Administrator programs the mezzanine cards on the blades during discovery. After the mezzanine cards are programmed, powering up the enclosure takes only 1 to 2 minutes.

The enclosure and the Insight Display now have power. Configure the enclosure ("Running the Insight Display installation steps" on page 65 ) using the Insight Display.

Cabling and powering up the enclosure 64

Contents

HP BladeSystem c7000 Enclosure Setup and Installation Guide Page Contents HP BladeSystem Insight Display Troubleshooting Support and other resources Regulatory compliance notices Documentation feedback Planning the installation Rack requirements The enclosure is compatible with the following racks: All HP 10000 and 10000G2 Series racks except the HP 10614 rack NOTE: •Telco racks Rack-freeenvironment requirements Warning, caution, and important messages CAUTION: Space and airflow requirements Temperature requirements Power requirements Grounding requirements Component and LED identification Power supply bay numbering Power supply LEDs Device bay numbering Full-heightdevice bay numbering Half-heightdevice bay numbering HP BladeSystem Insight Display components Location Discovery Services Enclosure rear components Fan bay numbering Fan LED Onboard Administrator components HP c7000 Onboard Administrator with KVM components Interconnect bay numbering Installation Page Page Rack-freeinstallation Rack installation Measuring with the rack template Installing the rack rails Installing the enclosure into the rack Page Installing the rear cage into the enclosure Installing a power supply Page Installing blades Installing a full-heightblade Page Page Removing a device bay shelf Creating a full-heightdevice bay blank Page Installing a half-heightblade Installing a device bay shelf Page Page Connecting locally to a server blade with video and USB devices Accessing a server blade with local KVM Accessing local media devices Installing fans Page Installing Onboard Administrator modules Attaching components to the HP c7000 Onboard Administrator with KVM Installing interconnect modules Page Mapping to interconnect ports Mapping half-heightblades Mapping full-heightblades Mapping BL2x220c Blades Mapping the BL680c G7 Blade Interconnect bay identification Bay-to-baycrosslinks Device bay crosslinks Interconnect bay crosslinks Removing interconnect bay dividers Installing interconnect bay dividers Cabling and powering up the enclosure Onboard Administrator cabling Enclosure link cabling Cabling a PC to the enclosure service port Cabling the network to the enclosure Single-phaseAC configuration Page 8.Open the snap clamps, and then insert each power cord inside each clamp Slide the power cord retention bracket until the bracket touches the enclosure PDU installation Page Three-phaseAC configuration HP BladeSystem Insight Display Page oNone Enabled—You Disabled—All Not Present _ and . is used to signal the end of the name Yes—Copy No—Continue 8.Verify all components are installed and cabled before continuing Navigating the Insight Display Health Summary screen Page Page Enclosure Settings screen Enclosure Info screen Blade and Port Info screen Turn Enclosure UID On/Off screen Page View User Note screen Chat Mode screen Troubleshooting Important safety information Symbols on equipment Warnings and cautions Power errors Cooling errors Location errors Configuration errors Device failure errors Page Support and other resources Réparation par le client (CSR) Riparazione da parte del cliente Reparaciones del propio cliente Reparo feito pelo cliente Page Page Page Regulatory compliance notices FCC rating label FCC Notice, Class A Equipment FCC Notice, Class B Equipment Modifications Cables Canadian notice (Avis Canadien) European Union regulatory notice Page Chinese notice Laser compliance Do not try to open the module enclosure. There are no •Allow only HP Authorized Service technicians to repair the unit Battery replacement notice Taiwan battery recycling notice Power cord statement for Japan Electrostatic discharge Acronyms and abbreviations CSA CSR ESD ICPM USB Documentation feedback Index