Removing the Module, At Power On | HP J3178A guide

the Management	Module
Installing

Installing the Management Module

Removing the Module

5.Turn on the power to the switch by plugging in the power cord. During power-on, the following occurs:

At Power On	The switch begins its power-on self test followed by the module’s self
	test. Ports are temporarily disabled until the Switch Management
	Module configures the ports.
During Self Test	All Switch and Module LEDs are on for approximately 5 seconds, then
	just the switch Power and Fault LEDs and the Management Module
	Self Test and Fault LEDs are on for the remainder of the self test. The
	switch and module self tests require approximately 15 seconds total.
After Self Test	The switch Fault LED and the module LEDs (Self Test and Fault) turn off.

If the module Fault LED stays on or flashes, refer to chapter 7, “Trouble- shooting” in this guide.

You have now completed installation and verification of the module.

To configure IP/IPXcommunication for the Switch Management Module, see chapter 4, “Configuring the Switch From the Console”.

Removing the Module

The module is removed from the switch by reversing the installation steps described earlier in this document. When handling the module, be sure to follow the anti-static precautions described on page 1-2.

	To remove the module, follow these steps:
	1.	Remove power from the switch by unplugging the power cord.
	2.	Unscrew the two captured screws holding the module in the switch.
	3.	Pull the module out of the slot.
	4.	Replace the Management Slot cover plate.

C a u t i o n	Replace the cover plate over the slot using the two screws that hold it in place.
	Be careful not to overtighten the screws. When using the switch, the cover
	plate must always be installed. This is required for safety and to ensure proper
	switch cooling.

1-4

Image 14

HP J3178A manual Removing the Module, At Power On

Contents

HP AdvanceStack Switch 208/224 Management Module Page HP AdvanceStack Switch 208/224 Management Module Installation and Reference Guide Publication Number HP FTP Library Service HP Customer Support ServicesHow to get the latest software/agent firmware World Wide Web Location Phone Number HP First Fax Retrieval ServiceAdditional HP Support Services Contents Monitoring Switch Operation From the Console Spanning Tree Operation Viii Installing the Management Module Installing the Management Module Installing Installing the Management Module Installation StepsAnti-Static Precautions Included Parts Remove the cover plate At Power On Removing the Module Management Module Description Overview Management Module Description Management Module Description Module Features Page Switch Console T e Connecting a Console to the Switch Switch Console Connecting a PC or Terminal to the Console RS-232 Port Remote Console Connection Using a Modem and a PC Modem Cable Pin-Out How To Start a Console Session Starting and Ending a Console Session How To End a Console Session Main Menu Main Menu Features Screen Structure and Navigation Actions line How To Navigate in the Console TaskActions Using Password Security Level Actions Permitted Capabilities, also set an Operator password To set Manager and Operator passwords To Delete Password Protection To Recover from a Lost Manager Password To Recover from a Lost Operator Password Select Delete Password Protection Rebooting the Switch Reboot Switch Option in the Main Menu Switch Console Example of a Configuration Change Requiring a Reboot How To Exit from the command prompt Advanced CommandsHow To Use the Advanced Commands Listing of Commands Available under Advanced CommandsPage Configuring the Switch From the Console Configuring the Switch From the Console Configuring Default values are shown in brackets Configurable Features How To Access the Switch Configuration System Configuration Configuring Configuring the Switch From the Console Port Configuration Example of the Port Configuration Screen IPX Service Configuring the Switch From the Console Internet IP Service To configure the switch for Bootp Using BootpTo manually configure the switch for IP Bootp Operation Where How To Configure the Switch for Snmp Communities Snmp Communities Snmp Communities Add or Edit Screen Trap Receivers Serial Link Configuration 10. The Serial Link Configuration Screen Default Values Console Configuration 11. The Console Configuration Screen Default Values Spanning Tree Configuration Press the Space bar to select Yes . This enables STP 12. Example of the STP Configuration Screen 13. The Default Network Monitoring Configuration Screen Network Monitoring Port 14. Example of Selecting a Monitoring Port Saving Configurations Page Monitoring Switch Operation From the Console Main Menu Data Type Purpose Monitoring Monitoring Switch Operation From the ConsoleStatus and Counters Menu Switch Information Example of Switch Information Port Status Example of Port Status Port Counters Example of Port Counters Port Counters Show Details Example of Port Counters Show Details Address Table Example of the Address Table Port Address Table To use the port address table Example of a Port Address Table for a Specific Port Spanning Tree STP Information Example of Spanning Tree Information 10. Example of STP Port Information Operation and read the Ieee 802.1d standards document Event Log Severity Date Time System Module Event Log Control Keys Key Action Switch Console Using Snmp To Monitor and Manage the Switch Snmp Management Features HP Proprietary MIBs include Snmp Configuration Process Advanced Management Rmon Ease Support Rmon Troubleshooting Status Description TroubleshootingChecking the Module LEDs Problem/Solution Table Problem Solution Testing the Switch and Management Module IP Configuration ErrorsDiagnostic Tests Testing the Switch’s Ports and the Links Troubleshooting Resetting the Switch Clearing Passwords on the Switch Console T e HP BBS Page Specifications Environmental Specifications Supported Mibs Regulatory Statements Vcci Class 1 For Japan OnlyPage End Modem ConfigurationAt the switch Modem Configuration At the user end File Transfers Downloading an Operating System Using Tftp To Download the OS File File Transfers Writing System Software to FLASH, Back Soon Using the SNMP-Based HP Download Manager Using the Switch-to-Switch Download Using the Zmodem to Download the OS File Jumping to console code Troubleshooting Tftp Downloads Figure C-3. Example of Message for Download Failure File to be copied Transferring Switch Configurations Command Function Configuration Zput config remotefile overwrite dos/unix Spanning Tree Operation Spanning Tree Protocol STP Spanning Tree Operation Index Clear button description … Defaultconfig IP/IPX MIB STP Tftp Page 5966-5228