113 | HP NetServer 5971-0821 guide

registry editor 25 removing a host adapter 30 removing the driver 30 troubleshooting 31–35

113

Image 119

HP NetServer 5971-0821 manual 113

Contents

HP Part Number Audience Assumptions Contents Novell NetWare Installation Microsoft Windows 2000 Installation Linux Support Product Specifications Troubleshooting 101 SCO OpenServer InstallationSCO UnixWare Installation Index 111 Warranty and Support 109Regulatory Information 103 HP Ultra3 Single Channel Scsi Host Bus Adapter Installation and Setup Primary and Secondary Bus Segments Bus Segments on the HP Ultra3 Scsi Host Adapter Bit and 64-bit Expansion Slots Installing the HP Ultra3 Scsi Host Bus Adapter Host Bus Adapter Installed in 64-bit Slot Terminate the Ends Setting Up Scsi DevicesChoosing Scsi Cables Check the Scsi IDsPage Connecting the Scsi Host Adapter to the Common Tray Connecting Scsi Devices Common Tray Cable Connection Connecting the Scsi Host Adapter to a Hot-Plug Cage Hot-Plug Cage Cable Connections Connecting Ultra/Fast Wide Scsi Devices Connecting Ultra/Fast Wide Scsi Devices Connecting Internal Ultra/Fast Narrow Devices Connecting Ultra/Fast Narrow Devices Connecting External Scsi Devices 10. Connecting External Scsi Devices Embedded Ultra3 Drivers HP Ultra3 Scsi Host Adapter Driver SoftwarePreloaded Ultra3 Drivers Troubleshooting Scsi Device Configuration Configuration with SCSISelectBoot Device Options Starting SCSISelect SCSISelect Options Available Default SettingsAdvanced Configuration Options Scsi Bus Interface Definitions Using SCSISelect SettingsExiting SCSISelect Scsi Device Configuration Boot Device Options Advanced Configuration Options Page Page Using Scsi Disk Utilities Adaptec Ultra3 PCI Scsi Controller NT4.0 Microsoft Windows NT InstallationInstalling the Driver When Installing Windows NT Completing a Fresh Windows NT 4.0 Installation From CD-ROM Installing the Driver When Windows NT is Already Installed Updating Windows NT Using Advanced Configuration Parameters Regdword Using Windows NT Scsi Parameters Using Driver-specific Parameters Page Type a\nt4\hotp160m.reg and press Enter Hot-Plug PCI Feature Removing a Host Adapter Using Windows NT and the Host Adapter Removing a Host Adapter in Windows NT Problems and Solutions Press spacebar NOW to invoke the Last Known Good menu Error Messages Xxxxx021 Target device protocol error Adpu160m.sys Error MessagesXxxxx010 Error issuing command Xxxxx011 Error issuing command Xxxxx032 Target device busy Xxxxx023 Target device parity errorXxxxx024 Data overrun or underrun Xxxxx031 Target device queue full Xxxxx0ce Scatter/gather limit exceeded Xxxxxd4 Adapter hardware failure adapter resetXxxxx0d6 Internal driver error Xxxxx097 Unable to allocate memoryPage Press any key to boot from CD Microsoft Windows 2000 InstallationInstalling the Driver When Installing Windows Click the Control Panel Using Windows 2000 Scsi Parameters Regdword Regsz Troubleshooting Problems and Solutions Driver Error Messages Xxxxx021 Target device protocol error Xxxxx089 Unable to allocate memory Xxxxxd4 Adapter hardware failure adapter reset Page NetWare 3.12/3.2 Novell NetWare InstallationInstalling the Driver When Installing NetWare Download the Nwpa Update Package Lswap loader.exe \server.312\server.exe cd \server.312 Copy cdrom.nlm to c\server.312\cdsave Load c\server.312\adpt160m slot=2 NetWare 4.12/4.2 Select Save parameter and continue, and press Enter NetWare Mkdir c\scsi Copy a\dos\*.* c\scsi DOS Drivers for CD-ROM AccessInstall CD-ROM Drivers on a DOS Bootable Hard Disk Load pathnameadpt160m options Installing the Driver When NetWare is Already Installed Load c\nwserver\adpt160m verbose=y Loading the Driver at Server BootupUsing the Load Command Line Options Load pathnameadpt160m.ham options Option Values Default Description Adpt160m.ham Command Line Options Multluntargets= Binary Hex Bit Mask Options Load a\netware\adpt160m.ham Using NetWare and the Host AdapterSample Load Commands Using Removable Media Lock Status Mount Status Load pathnameadpt160m Using the NetWare Tape BackupUsing a CD-ROM with NetWare Cd mount x name Optimizing PerformanceScan all luns Cd device list Xxxxx081 Adapter software initialization failure Xxxxx080 Unable to allocate memoryPage Xxxxx0a9 Possible interrupt conflict Xxxxx0a4 Scsi bus reset by third party hardwareXxxxx0c9 Invalid command line parameter Xxxxx0ac Driver already loaded for all host bus adaptersPage Installing SCO OpenServer SCO OpenServer InstallationInstalling the Driver When Installing SCO OpenServer When you see these prompts Umount /stand Name Description Logical Bus Adapter Device Unit Prefix Type Number Host Enter Using Multiple Host Adapters Using SCO OpenServer and the Host Adapter Using Tunable Parameters for the ad160 Driver Setting ParametersChanging the Boot Disk Using Wide Scsi Host Adapters and Devices Enabling Scatter/Gather and Tagged Queuing Changing the Maximum Number of LUNs Supported My computer does not recognize my host adapter My computer does not recognize my Scsi devices Am having problems booting the computer from a Scsi drive Ad160 Sdsk My computer hangs during heavy system load activity My computer crashes or displays panic messages at boot time Type Y to rebuild the kernel environment Reboot the system Xxxxx0ca Cannot initialize device Page Installing the Driver When Installing UnixWare SCO UnixWare Installation Installing the Driver When UnixWare is Already Installed Pkgadd -d diskette1 Back Up the ComputerLoad the Package Cat /etc/conf/sdevice.d/adst21 Modify the New System FileRebuild the UnixWare Kernel Type pkginfo -l adstxx and press Enter Cd /etc/conf/cf.d cp unix /stand/unix cd Shutdown -g0 Using UnixWare and the Host AdapterBoot the New Kernel Cd /etc/conf/bin Idbuild -B Etc/conf/bin/idbuild -B Cp /etc/conf/cf.d/unix /stand/unix Using Tunable ParametersRemoving the Driver Etc/conf/bin/idinstall -d adst70 Etc/conf/bin/idinstall -d adst21 Troubleshooting Xxxxx011 Error issuing command Adapter was given more or less data than was expected Xxxxx046 Target device did not respond to abort sequence Xxxxx097 Unable to allocate memory Linux Operating System World Wide Web URL Linux SupportPage Electrical Product Specifications Environmental Physical Regulatory 100 Device connected, but not ready TroubleshootingTroubleshooting Checklist Common Error Messages 102 Start unit request failedTime-out failure during … Class B Equipment Regulatory InformationRegulatory Notices Electromagnetic Compliance Federal Communications Commission 104 Class a AccessoriesClass a Equipment 105 For products labeled as Class BFor products labeled as Class a 106 Class a Warning 107 108 Declaration of Conformity US, EU, Australia 109 Warranty and SupportHardware Accessories Limited Warranty Hewlett-Packard Hardware Accessories Canada HP Repair and Telephone SupportWorld Wide Web Third-Party Hardware Products 111 Index 112 113 114