System Configuration | HP NuDAQ I-9111DG/HR guide

****** PCI-9111 Utility Rev. 1.0 ******

Copyright © 1995-1996, ADLINK Technology Inc. All rights reserved.

<F1>: Configuration.

<F2>: Calibration.

<F3>: Function testing.

<Esc>: Quit.

>>>Select function key F1 ~ F3, or press <Esc> to quit. <<<

7.1.2System Configuration

This function guides you to configure the PCI-9111 card, and set the right hardware configuration. The configuration window shows the setting items that you have to set before using the PCI-9111 card.

The following diagram will be displayed on the screen as you choose the Configuration function from main menu.

****** Calibration of PCI9111 ******


<1> Card Type		9111DG
<2> ADC Trigger	Source	Internal
<3> Timer Clock	Source	Internal
<4> DA Polarity	setting	Bipolar
<5> AD Input Range		Gain=1 Bipolar(-10V~10V)

>>><Up/Down>: Select Item, <PgUp/PgDn>: Change Setting <<<

Software Utility ∙69

Image 79

HP NuDAQ I-9111DG/HR manual System Configuration

Contents

NuDAQ Trademarks Questions Getting service from AdlinkPage B l e o f C o n t e n t s Features Applications Specifications Software SupportingPCI PnP Registers Address Map Interrupt Control Libraries Installation Programming GuideHardware Interrupt Clear Register Conversion Table of Contents ∙ 9111util What do you need VR Assignment Adjustment How to Use This Guide Page Introduction Features Applications Specifications Unipolar 0~10V Bipolar -10V~+10V Programming Library Software Supporting DASYLabTM PRO PCIS-LVIEW LabVIEW DriverPCIS-VEE HP-VEE Driver DAQBenchTM ActiveX Controls PCIS-OPC OPC Server PCIS-ICL InControlTM Driver Unpacking Installation∙ Software Installation Guide What You Have PCB Layout of the PCI-9111 PCI-9111s Layout Jumper Descriptions Hardware Installation Outline Connectors Pin Assignment Device Installation for Windows Systems∙ CN 1 Digital Signal Input DI 0 ~ ∙ CN 3 Analog Input/Output, Extended I/O, Trigger Signals ∙ CN 2 Digital Signal Output do 0 ~ Connect with ACLD-9182 Daughter Board ConnectionConnect with ACLD-8125 Connect with ACLD-9137 PCI PnP Registers Registers Format I/O Address I/O Address MapA/D Data Registers Address Write Read Address Base + 6h Attribute write only Data Format Bit A/D Channel Control RegisterAddress Base + 0h Attribute read only Data Format Bit Address Base + 8h Attribute write only Data Format Bit A/D Input Signal Range Control RegisterA/D Channel Read Back Register Address Base + 6h Attribute read only Data Format Bit Address Base + 0Ah Attribute write only Data Format Bit A/D Trigger Mode Control RegisterA/D Range and Status Read back Register Address Base + 8h Attribute read only Data Format Bit Address Base + 0Eh Attribute write only Data Format Bit Mode DescriptionAddress Base + 0Ch Attribute write only Data Format Bit Address Base + 0Ah Attribute read only Data Format Bit 12 A/D Mode & Interrupt Control Read Back RegisterHardware Interrupt Clear Register Address Base + 48h Attribute write only Data Format Bit Address Base + 4h Attribute read only Data Format Bit Address Base + 4h Attribute write only Data Format BitAddress Base + 2h Attribute read only Data Format Address Base + 2h Attribute write only Data Format Bit 15 D/A Output RegisterAddress Base + 40h ~ Base + 46h A/D Conversion Operation Theorem 2 A/D Signal Source Control 1 A/D Conversion Procedure Analog Input Signal Connection 3 A/D Trigger Source Control Signal Range External Trigger EITS=1, TPST=don‘t care 4 A/D Data Transfer Modes Fifo Half-Full Polling EOC Interrupt Transfer Pre-Trigger Control Time FFF 6 A/D Data Format Interrupt Control System Architecture IRQ Level SettingDual Interrupt System Extended Digital I/O Port Interrupt Source Control 44mV 88mV D/A Conversion Digital Input and Output Timer/Counter Operation Introduction Pre-Trigger Counter Pacer Trigger Source4 I/O Address ++ Library Libraries Installation Data Types Programming Guide Naming Convention ++ Windows 9111Initial9111DO ++ DOS 9111DI 9111DOChannel 9111EDI 9111DIChannel 10 9111EDOReadBack 9111EDO 11 9111SetEDOFunction 13 9111ADReadData 12 9111DA 15 9111ADSetChannel 14 9111ADReadDataRepeat 16 9111ADGetChannel Input Range Gain Gain Code 17 9111ADSetRange 19 9111ADGetStatus 18 9111ADGetRange 20 9111ADSetMode 22 9111INTSetReg 21 9111ADGetMode 23 9111INTGetReg 24 9111ResetFIFO 26 9111Set8254 25 9111ADSoftTrigger 27 9111Get8254 28 9111ADTimer 30 9111CounterRead 29 9111CounterStart 31 9111CounterStop 32 9111INTSourceControl 34 9111GetIRQChannel 33 9111CLRIRQ 36 9111ADFFHFPolling 35 9111GetIRQStatus 38 9111ADHRAquire 37 9111ADAquire 39 9111ADINTStart 40 9111ADFFHFINTStart ++ Library ∙61 42 9111ADFFHFINTStatus 41 9111ADINTStatus 43 9111ADFFHFINTRestart 44 9111ADINTStop What do you need Calibration VR Assignment A/D AdjustmentFunctions of VRs Bipolar Analog Output D/A Adjustment Unipolar Analog Output 9111util Software UtilityRunning 9111util.exe System Configuration Calibration Function Testing Menu Window Functional Testing Ieeprom Product Warranty/Service