Installation, What You Have, Unpacking | HP NuDAQ I-9111DG/HR

2

Installation

This chapter describes how to install the PCI-9111. At first, the contents in the package and unpacking information that you should be careful are described.

The PCI-9111 does an automatic configuration of the IRQ, port address, and BIOS address. Therefore, it is not necessary to set the above configurations as you use ISA DAS card.

2.1What You Have

In addition to this User's Manual, the package includes the following items:

∙PCI-9111 Enhanced Multi-function Data Acquisition Card

∙ADLINK CD

∙Software Installation Guide

If any of these items is missing or damaged, contact the dealer from whom you purchased the product. Save the shipping materials and carton in case you want to ship or store the product in the future.

2.2Unpacking

Your PCI-9111 card contains sensitive electronic components that can be easily damaged by static electricity.

The card should be done on a grounded anti -static mat. The operator should be wearing an anti -static wristband, grounded at the same point as the anti-static mat.

Installation ∙ 7

Image 17

HP NuDAQ I-9111DG/HR Installation, What You Have, Unpacking, ∙ PCI-9111 Enhanced Multi-function Data Acquisition Card

Contents

NuDAQ Trademarks Questions Getting service from AdlinkPage PCI PnP Registers Address Map Features Applications Specifications Software SupportingB l e o f C o n t e n t s Hardware Interrupt Clear Register Libraries Installation Programming GuideConversion Interrupt Control Table of Contents ∙ 9111util What do you need VR Assignment Adjustment How to Use This Guide Page Introduction Features Applications Specifications Unipolar 0~10V Bipolar -10V~+10V Programming Library Software Supporting PCIS-VEE HP-VEE Driver PCIS-LVIEW LabVIEW DriverDAQBenchTM ActiveX Controls DASYLabTM PRO PCIS-OPC OPC Server PCIS-ICL InControlTM Driver ∙ Software Installation Guide InstallationWhat You Have Unpacking PCB Layout of the PCI-9111 PCI-9111s Layout Jumper Descriptions Hardware Installation Outline ∙ CN 1 Digital Signal Input DI 0 ~ Device Installation for Windows SystemsConnectors Pin Assignment ∙ CN 3 Analog Input/Output, Extended I/O, Trigger Signals ∙ CN 2 Digital Signal Output do 0 ~ Connect with ACLD-8125 Daughter Board ConnectionConnect with ACLD-9137 Connect with ACLD-9182 PCI PnP Registers Registers Format A/D Data Registers I/O Address MapAddress Write Read I/O Address Address Base + 0h Attribute read only Data Format A/D Channel Control RegisterBit Address Base + 6h Attribute write only Data Format Bit A/D Channel Read Back Register A/D Input Signal Range Control RegisterAddress Base + 6h Attribute read only Data Format Bit Address Base + 8h Attribute write only Data Format Bit A/D Range and Status Read back Register A/D Trigger Mode Control RegisterAddress Base + 8h Attribute read only Data Format Bit Address Base + 0Ah Attribute write only Data Format Bit Address Base + 0Ch Attribute write only Data Format Bit Mode DescriptionAddress Base + 0Eh Attribute write only Data Format Bit Hardware Interrupt Clear Register 12 A/D Mode & Interrupt Control Read Back RegisterAddress Base + 48h Attribute write only Data Format Bit Address Base + 0Ah Attribute read only Data Format Bit Address Base + 2h Attribute read only Data Format Address Base + 4h Attribute write only Data Format BitAddress Base + 4h Attribute read only Data Format Bit Address Base + 40h ~ Base + 46h 15 D/A Output RegisterAddress Base + 2h Attribute write only Data Format Bit A/D Conversion Operation Theorem 2 A/D Signal Source Control 1 A/D Conversion Procedure Analog Input Signal Connection 3 A/D Trigger Source Control Signal Range External Trigger EITS=1, TPST=don‘t care 4 A/D Data Transfer Modes Fifo Half-Full Polling EOC Interrupt Transfer Pre-Trigger Control Time FFF 6 A/D Data Format Dual Interrupt System IRQ Level SettingInterrupt Control System Architecture Extended Digital I/O Port Interrupt Source Control 44mV 88mV D/A Conversion Digital Input and Output Timer/Counter Operation Introduction 4 I/O Address Pacer Trigger SourcePre-Trigger Counter ++ Library Libraries Installation Data Types Programming Guide Naming Convention 9111DO 9111Initial++ DOS ++ Windows 9111DI 9111DOChannel 9111EDI 9111DIChannel 10 9111EDOReadBack 9111EDO 11 9111SetEDOFunction 13 9111ADReadData 12 9111DA 15 9111ADSetChannel 14 9111ADReadDataRepeat 16 9111ADGetChannel Input Range Gain Gain Code 17 9111ADSetRange 19 9111ADGetStatus 18 9111ADGetRange 20 9111ADSetMode 22 9111INTSetReg 21 9111ADGetMode 23 9111INTGetReg 24 9111ResetFIFO 26 9111Set8254 25 9111ADSoftTrigger 27 9111Get8254 28 9111ADTimer 30 9111CounterRead 29 9111CounterStart 31 9111CounterStop 32 9111INTSourceControl 34 9111GetIRQChannel 33 9111CLRIRQ 36 9111ADFFHFPolling 35 9111GetIRQStatus 38 9111ADHRAquire 37 9111ADAquire 39 9111ADINTStart 40 9111ADFFHFINTStart ++ Library ∙61 42 9111ADFFHFINTStatus 41 9111ADINTStatus 43 9111ADFFHFINTRestart 44 9111ADINTStop What do you need Calibration Functions of VRs A/D AdjustmentVR Assignment Bipolar Analog Output D/A Adjustment Unipolar Analog Output Running 9111util.exe Software Utility9111util System Configuration Calibration Function Testing Menu Window Functional Testing Ieeprom Product Warranty/Service