9111DOChannel, 9111DI | HP NuDAQ I-9111DG/HR guide

5.5_9111_DO_Channel

@Description

This function is used to write data to digital output ports. There are 16 digital output channels on PCI_9111. You can control each digital output channel by this function directly. When performing this function, the digital output port is written and the output status will be changed to the value you had specified to do_data.

@ Syntax

C/C++ (DOS)

U16 _9111_DO_Channel (U16 cardNo, U16 do_ch_no , Boolean do_data)

C/C++ (Windows 95)

U16 W_9111_DO_Channel (U16 cardNo, U16 do_ch_no , Boolean do_data)

Visual Basic (Windows 95)

W_9111_DO_ByVal cardNo As Integer, ByVal do_ch_no As Integer, ByVal do_data As Byte) As Integer

@ Argument
cardNo:	The card number of PCI-9111 card initialized

do_ch_no: The channel number to perform digital output, the value has to be set from 0 to 15.

do_data: The value will be written to digital output port, either 0 or 1.

@Return Code

ERR_NoError

ERR_InvalidDOChannel

5.6_9111_DI

@Description

This function is used to read data from digital input ports. There are 16 digital input channels on PCI_9111. The digital input status can be accessed by this function directly.

@ Syntax

C/C++ (DOS)

U16 _9111_DI (U16 cardNo, U16 *DIData)

C/C++ (Windows 95)

U16 W_9111_DI (U16 cardNo, U16 *DIData)

Visual Basic (Windows 95)

W_9111_DI (ByVal cardNo As Integer, DIData As Integer) As Integer

@ Argument

C/C++ Library ∙39

Image 49

HP NuDAQ I-9111DG/HR manual 9111DOChannel, 9111DI

Contents

NuDAQ Trademarks Questions Getting service from AdlinkPage B l e o f C o n t e n t s Features Applications Specifications Software SupportingPCI PnP Registers Address Map Hardware Interrupt Clear Register Libraries Installation Programming GuideConversion Interrupt Control Table of Contents ∙ 9111util What do you need VR Assignment Adjustment How to Use This Guide Page Introduction Features Applications Specifications Unipolar 0~10V Bipolar -10V~+10V Programming Library Software Supporting PCIS-VEE HP-VEE Driver PCIS-LVIEW LabVIEW DriverDAQBenchTM ActiveX Controls DASYLabTM PRO PCIS-OPC OPC Server PCIS-ICL InControlTM Driver ∙ Software Installation Guide InstallationWhat You Have Unpacking PCB Layout of the PCI-9111 PCI-9111s Layout Jumper Descriptions Hardware Installation Outline Connectors Pin Assignment Device Installation for Windows Systems∙ CN 1 Digital Signal Input DI 0 ~ ∙ CN 3 Analog Input/Output, Extended I/O, Trigger Signals ∙ CN 2 Digital Signal Output do 0 ~ Connect with ACLD-8125 Daughter Board ConnectionConnect with ACLD-9137 Connect with ACLD-9182 PCI PnP Registers Registers Format A/D Data Registers I/O Address MapAddress Write Read I/O Address Address Base + 0h Attribute read only Data Format A/D Channel Control RegisterBit Address Base + 6h Attribute write only Data Format Bit A/D Channel Read Back Register A/D Input Signal Range Control RegisterAddress Base + 6h Attribute read only Data Format Bit Address Base + 8h Attribute write only Data Format Bit A/D Range and Status Read back Register A/D Trigger Mode Control RegisterAddress Base + 8h Attribute read only Data Format Bit Address Base + 0Ah Attribute write only Data Format Bit Address Base + 0Eh Attribute write only Data Format Bit Mode DescriptionAddress Base + 0Ch Attribute write only Data Format Bit Hardware Interrupt Clear Register 12 A/D Mode & Interrupt Control Read Back RegisterAddress Base + 48h Attribute write only Data Format Bit Address Base + 0Ah Attribute read only Data Format Bit Address Base + 4h Attribute read only Data Format Bit Address Base + 4h Attribute write only Data Format BitAddress Base + 2h Attribute read only Data Format Address Base + 2h Attribute write only Data Format Bit 15 D/A Output RegisterAddress Base + 40h ~ Base + 46h A/D Conversion Operation Theorem 2 A/D Signal Source Control 1 A/D Conversion Procedure Analog Input Signal Connection 3 A/D Trigger Source Control Signal Range External Trigger EITS=1, TPST=don‘t care 4 A/D Data Transfer Modes Fifo Half-Full Polling EOC Interrupt Transfer Pre-Trigger Control Time FFF 6 A/D Data Format Interrupt Control System Architecture IRQ Level SettingDual Interrupt System Extended Digital I/O Port Interrupt Source Control 44mV 88mV D/A Conversion Digital Input and Output Timer/Counter Operation Introduction Pre-Trigger Counter Pacer Trigger Source4 I/O Address ++ Library Libraries Installation Data Types Programming Guide Naming Convention 9111DO 9111Initial++ DOS ++ Windows 9111DI 9111DOChannel 9111EDI 9111DIChannel 10 9111EDOReadBack 9111EDO 11 9111SetEDOFunction 13 9111ADReadData 12 9111DA 15 9111ADSetChannel 14 9111ADReadDataRepeat 16 9111ADGetChannel Input Range Gain Gain Code 17 9111ADSetRange 19 9111ADGetStatus 18 9111ADGetRange 20 9111ADSetMode 22 9111INTSetReg 21 9111ADGetMode 23 9111INTGetReg 24 9111ResetFIFO 26 9111Set8254 25 9111ADSoftTrigger 27 9111Get8254 28 9111ADTimer 30 9111CounterRead 29 9111CounterStart 31 9111CounterStop 32 9111INTSourceControl 34 9111GetIRQChannel 33 9111CLRIRQ 36 9111ADFFHFPolling 35 9111GetIRQStatus 38 9111ADHRAquire 37 9111ADAquire 39 9111ADINTStart 40 9111ADFFHFINTStart ++ Library ∙61 42 9111ADFFHFINTStatus 41 9111ADINTStatus 43 9111ADFFHFINTRestart 44 9111ADINTStop What do you need Calibration VR Assignment A/D AdjustmentFunctions of VRs Bipolar Analog Output D/A Adjustment Unipolar Analog Output 9111util Software UtilityRunning 9111util.exe System Configuration Calibration Function Testing Menu Window Functional Testing Ieeprom Product Warranty/Service