Activating or Deactivate GK Client Function | Huawei v200r001

User Manual - Configuration Guide (Volume 3)	Chapter 4
Versatile Routing Platform	GK Client Configuration

interface. Only after one interface is specified as H.323 gateway interface, can the function of CK Client be activated and can GK Client register to GK Server.

Please perform the following configurations in interface configuration mode.

Table VC-4-1Specifying One Interface as H.323 Gateway Interface

Operation	Command

Specify one interface as H.323 gateway interface	h323-gateway voip interface
Cancel one interface as H.323 gateway interface	no h323-gateway voip interface

By default, no interface is specified as H.323 gateway interface.

4.2.3 Activating or Deactivate GK Client Function

Only when one interface is successfully configured as H.323 gateway interface, can GK Client function be activated. When the H.323 gateway interface is re-specified or the relevant parameters (such as gateway alias and corresponding Gatekeeper name) of other gateways are modified, you should activate GK Client function anew, so that the information related to Client stored in GK Server is updated timely.

Please perform the following configurations in global configuration mode.

Table VC-4-2Activate or Deactivate GK Client Function

Operation	Command

Activate GK Client function	gateway
Deactivate GK Client function	no gateway

By default, GK Client function is deactivated.

4.2.4 Configuring Gateway Alias

Gateway alias is used to register at GK Server and identify gateway. One gateway can have only one alias.

Please perform the following configurations in interface configuration mode.

Table VC-4-3Configure Gateway Alias

Operation	Command

Configure gateway alias	h323-gateway voip h323-id namestring
Delete gateway alias	no h323-gateway voip h323-id [ namestring ]

By default, the gateway alias is blank, i.e. no gateway alias configured.

4.2.5 Configure the GK Server Name and Address

When the GK Client of the router is activated, GK Client will automatically register the relevant information of the gateway to GK Server. Therefore, it needs to configure

4-2

Image 248

Huawei v200r001 user manual Activating or Deactivate GK Client Function, Configuring Gateway Alias

Contents

Huawei V200R001 Manual Version T2-080168-20011213-C-1.5 BOM31010868 Contents About This Manual Format Description Key Bracket, e.g. Enter , Tab , Backspace , or aKey 1 + Key Key 1, Key Symbol Action Description Security Configuration SC Huawei Configuration of IKE II. IKE features IKE Configuration Task List Creating IKE Security Policy Select Encryption Algorithm Select Authentication AlgorithmNo IKE security policy is created by default Select DH Group ID Set Pre-shared KeySelect Hashing Algorithm Set Lifetime of IKE Association SA Show IKE SA parameter Quidway# show crypto ike sa Networking requirements Show IKE security policy Quidway# show crypto ike policy II. Networking diagram III. Configuration procedure Problem 1 Invalid user ID information VPN Configuration VPN Table of Contents VPN features VPN Overview According to operation mode Classification of IP VPN II. According to the layer where the tunnel is III. According to service purpose IV. According to networking model Configuration of L2TP Brief Introduction to L2TP ProtocolOverview of Vpdn Brief induction to Vpdn Tunnel and session 2 L2TP ProtocolIII. Method to realize Vpdn II. Control message and data message III. Two typical L2TP tunnel modes IV. Call setup flow of L2TP tunnel Call setup flow of L2TP channel is shown in the following Features of L2TP protocol Figure VPN-2-3Call setup flow of L2TP channel Configuring at LAC Side Configuring L2TP1 L2TP Configuration Task List Disable Vpdn to run by default II. Create Vpdn group Configuring at LNS Side Disable Vpdn running by defaultIV. Set the connection request to originate L2TP channel Table VPN-2-4L2TP attribute table III. Create/delete virtual interface template No vpdn group group-numberAccept dialin l2tp virtual-template virtual No accept dialin Set local name of channel Optional configurationIII. Force local end to perform Chap authentication Local end does not perform Chap authentication by default LCP does not renegotiate by defaultIV. LNS forces LCP to renegotiate Set domain name delimiter and search sequence VII. Enable/disable hiding AV pairs Disable hiding AV pairs by default Monitoring and Maintenance of L2TP VIII. Force to disconnect tunnel Typical Configuration of L2TP Show l2tp session command domainNAS-Initialized VPN Networking requirement III. Configuration procedure Figure VPN-2-5Networking diagram of Client-Initialized VPN Client-Initialized VPN Single User Interconnects Headquarters via Router Chapter Fault Diagnosis of L2TP Brief introduction to the protocol Configuration of GREBrief Introduction to GRE Protocol II. Applicable range Figure VPN-3-2Format of transmission message in the tunnel Configuring GRE GRE Configuration Task List Creating Virtual Tunnel Interface Setting the Source Address of Tunnel InterfaceSetting the Destination Address of Tunnel Interface Setting the Network Address of Tunnel Interface Setting the Encapsulation Mode of Tunnel Interface MessageSetting the Identification Key Word of Tunnel Interface Setting Tunnel Interface to Check with Check Sum Show interface tunnel tunnel-number Monitoring and Maintenance of GREDisable tunnel interface to check with check sum by default Typical Configuration of GRE Figure VPN-3-6Networking diagram of GRE application Chapter Troubleshooting GRE Reliability Configuration LC Configuration of Backup Center Configuration of Hsrp Configuration of Backup Center Backup Center OverviewConfiguring the Backup Center Configuration Task List Backup logic-channel logic-channel No backup delay Backup state-up interval-time Configuring Routes for Main and Backup InterfacesBackup state-down number Monitoring and Maintaining of Backup Center Typical Configuration of Backup CenterAn example of Backup Between Interfaces An Example of Multiple Backup Interfaces Chapter Chapter Configuration of Hsrp Hsrp Overview Configuring Hsrp Starting Hsrp Function Setting Router’s Priority in Hsrp Hot Standby Group Setting Router’s Preemption Mode in Hsrp Standby GroupSetting Hsrp Authorization Word Standby group-number preempt Setting Hsrp Timer Table LC-2-4Set Hsrp authorization wordStandby group-numberauthentication string Monitoring the Specified Interface Table LC-2-6Monitor the specified interface Using Actual Interface MAC AddressModifying Virtual MAC Address Typical Configurations of Hsrp An example for single hot standby group configurationMonitoring and Maintaining Hsrp Show relevant Hsrp information Quidway# show standby 202.38.160.111 An example for setting Hsrp to monitor a specified interface An example for multiple hot standby groups configuration Fault Diagnosis and Troubleshooting of Hsrp QoS Configuration QC Apply CAR Rules to Packets Which is Matched the ACL CAR Configuration ExampleConfigure CAR Rules Based on the MAC Address Three service types of QoS Best-effort ServiceII.Integrated Service QoS Overview III. Differentiated Service Functions of QoS Chapter II. CAR Committed Access Rate Traffic Classification and PolicingTraffic Classification and Policing Introduction to Traffic Classification Features of Token Bucket Introduction to Traffic Policing III Complicacy Evaluation Introduction to CARII.Traffic Measuring with Token Bucket CAR Configuration CAR Configuration Task ListNo CAR rule is specified by default Specify CAR rules Monitoring and Maintenance of CAR Table QC-2-3Monitoring and maintenance of CARApply the CAR Rule on the Interface Show CAR statistics Quidway# show car interface serial CAR Configuration Example II.ConfigurationApplying CAR Rules to All Packets Requirements III. Configuration Apply CAR Rules to Packets Which is Matched the ACL II.Networking diagram Configure CAR Rules Based on the Priority LevelConfigure CAR Rules Based on the MAC Address Chapter Congestion Management Congestion and Congestion ManagementAbout Congestion Congestion Management Policy IV. WFQ Weighted Fair Queuing Fifo QueuingII. PQ Priority Queuing III. CQ Custom Queuing Selecting Congestion Management Policy Working Principle of Congestion Management Policy No. Advantages Disadvantages Queue Fifo III. CQ PQ Configuration task list Configuration of Congestion ManagementConfiguring PQ II. Configuring priority queue Priority-list list-number interface type number high medium Normal low Table QC-3-7Configuration of queue length of priority queue Interface adopts Fifo queuing by defaultIII. Applying priority queue to the interface IV. Maintaining and monitoring the priority queue II. Configuring the custom queue Configuring CQCQ configuration task list Operation Command Configure the default custom queue No custom-list list-number interface type number III. Applying custom queue to the interface No custom-list list-number queue queue-number limitCustom-list list-number queue queue-number byte-count No custom-list list-number queue queue-number byte-count Configuring WFQ WFQ configuration task listII. Configuring the weighted fair queue III. Maintenance and monitoring of the weighted fair queue CQ Configuration Example Configuration Example of Congestion ManagementPQ Configuration Example Figre QC-3-6Networking diagram of CQ Configuration Versatile Routing Platform Troubleshooting of Congestion Management DDR Configuration DC DDR in Which the Router Calls Back PC Configuring Synchronous/Asynchronous Serial Port Using DDRDDR Configuration Configuration of Modem Management Introduction to DDR Technology DDR ConfigurationBrief Introduction to Dial Configuration Preparing DDR Configuration Figure DC-1-1DDR configuration preparation flow Configuring DDR Configuring Legacy DDRConfiguration tasks of Legacy DDR include II. Configure an interface to send calls Dialer string dial-string isdn-address Dialer rotary-group number III. Configure an interface to receive calls Figure DC-1-2Schematic diagram of Dialer Rotary Group IV. Configure an interface to send and receive calls Versatile Routing Platform DDR Configuration Set the attribute parameters of Legacy DDR Table DC-1-13Set the idle time of busy interface Table DC-1-16Set access control of the dial interface Access-list access-list-numberdeny permitAccess-list access-list-number deny permit Permit deny Introduction to Dialer Profile Configuring Dialer ProfileDefault interval is 300 seconds IV. Set the attribute parameters of a dial interface II. Configuration task list of Dialer ProfileIII. Configure a logic dial interface Configuring Callback Bind physical interfaces for a dialer poolSignificance of callback II. Terms and abbreviations IV. Configure Isdn calling line identification callback Dialer caller remote-number callbackOr dialer caller remote-number Interface dialer Configure PPP callback User name callback-dialstring telephone-number Chapter Table DC-1-28Client end using Legacy DDR to configure PPP Configuring DDR Special Functions Configure Isdn dedicated line Autodial interval is 300 seconds by default II. Configure autodialIII. Configure cyclic use of dialer map Name Meaning Monitoring and Maintenance of DDRTable DC-1-34Configure cyclic use of dialer map Network requirements DDR Typical Configuration ExampleLegacy DDR Chapter Dialer Profile Chapter Point-to-Point DDR Networking diagramII. Configuration procedure Chapter Chapter Point-to-Multipoint DDR 8810063 Chapter Chapter 8810148 Multipoint-to-Multipoint DDR8810052 III. Configuration procedure Chapter Chapter Chapter Chapter DDR Bearing IPX Chapter Chapter Chapter DDR Bearing IP and IPX at the Same Time Chapter Chapter Chapter Flow Control of Dialer Profile MP over Dialer Profile-Case RouterA RouterB BRI02.2 661012 Chapter Figure DC-1-11Networking diagram of DDR Case Channels for Dial-up and Connection to the Remote End Case Chapter Two Serial Ports for Dial-up and Remote Dial Connection Case One Serial Port for Dial-up and Remote Dial Connection Case Chapter DDR for Access Service Chapter Chapter Chapter Chapter DDR for Inter-Router Callback Chapter DDR in Which the Router Calls Back PC III. Configuration procedure DDR for Autodial DDR Using Dialer Map Cyclically DDR Using Dialer Map as Backup Solution 1 Logical interface as backup interface Chapter Configuring Synchronous/Asynchronous Serial Port Using DDR Precautions for DDR ConfigurationConfiguring Dialer-group Configuring Network Layer Address Configuring PPP In Dialer Profile Configuration Mode Apply PAP authentication Chapter II. Apply Chap authentication Chapter Configuring PPP In Legacy DDR Configuration Mode Chapter II. Apply Chap authentication Chapter Troubleshooting DDR Configure Dialer-listDDR Fault Diagnosis Whether modem is normal III. Check whether dialer-group is configured IV. Check whether dialer-list is configured correctly Chapter DDR Fault Elimination Information displayed at the calling end Troubleshooting with DDR Debugging InformationHow to acquire DDR debugging information Information displayed at the call receiving end DDR link negotiation Down on interface Configuration of Modem Management Modem Management Functions Provided by VRP1.4Modem Script Function Timeout seconds Key words Description Configuring Modem Management Modem Management Configuration Task ListConfiguring Modem Call-In and Call-Out Authorities Configuring Modem Script Specifying the Event to Trigger Modem Script Configuring Modem Answer ModeExecuting Modem Script Manually Typical Configuration of Modem Management Managing Modem with Modem Script Networking requirements Direct Dial with Script Configuration requirementsRouter Initialization with Initialization Script Interactively Connect Cisco Router Through Modem VoIP Configuration VC VoIP Configuration IP Fax Configuration Iphc Configuration E1 Voice ConfigurationGK Client Configuration Versatile Routing Platform Table of Contents VoIP Configuration VoIP Overview II. H.323 protocol stack VoIP PrincipleBasic composition IP Voice Implementation over VRP III. a typical telephone call processing by VoIP IP Voice Feature over VRP Switch Router Capacity channel Chapter VoIP Configuration Task List Configuring Dial-peer Pots dial-peer configuration II. VoIP dial-peer configuration Configuring Dial Terminator Ip precedence priority-number Configuring Abbreviated Dialing Configuring Voice PortBy default, we do not configure the dial terminator By default, we do not configure the abbreviated dialing Table VC-1-6Configuring voice-port By default, please use the shortest number match policy Configuring Global Number Match PolicyConfiguring the Recovery Method of Voice Board VoIP Monitoring and Maintenance By default, Watchdog is enabled KHT Rcvccactivecall Channel = Status = Chtransframe Typical VoIP Configuration Examples Configuring Router FXS Port for Interconnection III. Configuration procedures Shanghai Chapter Figure VC-1-7RouterShenzhen FXO works in the Plar mode LAN VoIP Troubleshooting III. Configuration description IP Fax Configuration Configuring IP FaxTask List of IP Fax Configuration Overview to IP Fax Gateway does not use ECM mode by default Checking If Configuring Fax to Use ECM ModeConfiguring Fax Rate Configuring Fax Train Mode Configuring Fax Local-train Threshold ValueBy default, the fax rate will be determined by voice mode Mode is local-train mode local by default Configuring Gateway Carrier Transmit Energy Level Fax protocol t38 ls-redundancy numberNo fax protocol t38 ls-redundancy Fax protocol t38 hs-redundancy number By default, rtp protocol is used Monitoring and Maintenance of IP FaxBy default, T.38 protocol is used Typical Configuration of IP Fax Versatile Routing Platform IP Fax Configuration Chapter E1 Voice Configuration Overview of E1 Voice ConfigurationFunction of E1 Voice Usage of cE1/PRI Interface Features of E1 Voice Signaling modes supportedII. Protocols and standards supported III. Support single stage dialing and two-stage dialing E1 Voice Configuration Configuration Task List of E1 VoiceConfiguring Pots dial-peer IV. Integrated transmission of voice and data Configuring VoIP dial-peer Table VC-3-1Configuration Commands of Pots dial-peerIncoming called-number number No incoming called-number Configuring the Basic Parameters of E1 Interface Table VC-3-2Configuration Commands of VoIP dial-peer Configuring Voice Port E1 Interface Table VC-3-3Configuration Commands of E1 Interface Table VC-3-4Configuration Commands of E1 Voice Port Configuring E1 Voice R2 SignalingConfiguring DS0 group II. Configuring Related Parameters of R2 Signaling By default, the system has not created any DS0 group Table VC-3-6Configuration Commands of R2 Signaling Configuring the Basic Parameters of Isdn PRI Interface Pri-group timeslots timeslots-listNo pri-group Interface serial serial-no Maintaining the MFC Channel and Circuit of the Specified TS Monitoring and Maintenance of E1 VoiceConfiguring Voice Port Isdn PRI Interface II. show Command Related to E1 Voice Quidway# show voice-port III. debug Commands Related to E1 Voice R2 signalling call statistics Router Connected to PBX through E1 Voice Port Typical Configuration Examples of E1 VoiceTable VC-3-11debug Commands of E1 Voice Versatile Routing Platform Router Connected to PBX in Isdn PRI Mode Two-stage Dialing Configuration II. Netwoking diagram Parameter configuration of Beijing-side router Transmission of Data and Voice Simultaneously Fault Diagnosis and Troubleshooting of E1 Voice GK Client Configuration Configuration of GK ClientConfiguration Task List of GK Client Configuring One Interface as H.323 Gateway Interface Configuring Gateway Alias Configure the GK Server Name and AddressBy default, GK Client function is deactivated Activating or Deactivate GK Client Function By default, there is not any tech-prefix Configuring Tech-PrefixConfiguring GK Interworking Mode Versatile Routing Platform GK Client Configuration Typical Configuration Examples of GK ClientBe default, the GK interworking mode is cisco mode Chapter Fault Diagnosis and Troubleshooting of GK Client Iphc Configuration Overview of Iphc Iphc Configuration Configuration Task List of IphcEnable/disable RTP header compression No ip rtp compression-connections Configure the Cisco-compatible RTP header compression Configure the deleting of udpchk field from UDP headerBy default, the udpchk field in UDP packet field is set to No ip tcp header-compression Monitoring and Maintenance of Iphc Table VC-5-6Monitoring and Maintenance of Iphc How Are We Doing Excellent Good Fair Poor Mistake Suggested Correction Line No