Hunter Fan R410A manual Model FDKN series, Change by the jumper wire, Name, Function, Switch

Model: FDKN series

This diagram shows the PCB for the 151~251. The component layout on the 301 PCB is different, but the functions are the same.

J31

	Heat exchanger thermistor,
Heat exchanger thermistor	Return air thermistor	Remote controller
	(Thl-R1, Thl-A)
(Thl-R2)
		TB,3
	R16

Dip switch (SW5)

J9~J11

(SW10)

Dip switch (SW9)

J5~J8

(SW8)

J1~J4(SW7)

CNZ

SW10 SW5

J9 J10 J11

SW8 SW9

J5 J6 J7 J8

J4 J3 J2 J1 SW7

CNE

CNN1		CNH	R17
	CNB	L1	L2
J31
			CNW1
		IC11
	L4

R151

TB,2

TB,1

G

PCB power supply connector

(Primary side)

Adress switch (SW2)

SW2

IC9IC10

	C92
LED1	CNG
CNL	CNY

	C2
	R62
	IC8
	BZ
	CNT
CNJ	CNM

C104

PCB power supply connector

(Secondary side)

Louver motor	Connector	Fan motor
	(CNT)

●Change by the jumper wire

	Name		Function
J1 (SW7-1)		With	Input signal - Reverse invalid
		None (1)	Input signal - Rus stop
J2 (SW7-2)		With	Heating thermostat OFF-Lo
		None (1)	Heating thermostat OFF-Stop, Lo
J3 (SW7-3)		With	Normal operation operable
		None (1)	Operation permission prohibited
J4 (SW7-4)		With	Normal
		None (1)	Heating temp. +3
J5 (SW8-1)		With	Louver free stop control - Invalid
		None (1)	Louver free stop control - Effective
J6 (SW8-2)		With	Freeze prevention fan control activated.
		None (1)	Freeze prevention fan control deactivated.
J8 (SW8-4)		With	Model 151~251
		None (1)	Model 301

Note (1) “None” means that jumper wire is not provided on the PCB or the connection is cut

(2)The replacement board is not equipped with jumpers J1 ~ J8. Instead, SW7 and 8, with the same functions as jumpers J1~J8, are used in the position where the jumpers were previously. Set SW7 and 8 locally in accordance with the above table.

●Control change switch (SW5, SW9, SW10)

Function of DIP switch SW5 (Usually all turned OFF)

	Switch			Function
	ON		ON	Setting time : 1000hrs. (Unit stop)
SW5-3		SW5-4	OFF	Setting time : 1000hrs. (Display)
	OFF		ON	Setting time : 600hrs. (Display)
			OFF	Setting time : 180hrs. (when shipped from factory)

Function of DIP switch SW9 (Usually all turned OFF)

	Switch		Function
SW9-1		OFF	Custom code - Change
		ON	Custom code - Normal
SW9-2		OFF	Power failure security - Effective
		ON	Power failure security - Invalid
SW9-3		ON	Emergency operation
		OFF	Normal
SW9-4		ON	Fan control : Powerful mode
		OFF	Fan control : Mild mode

Note (1) It is normally ON only in the case of SW9-4.

Function of DIP switch SW10 (Usually all turned OFF)

	Switch			Function
SW10-1 (J9)			OFF	Auto swing fanction - None
			ON	Auto swing function - With
	OFF		OFF	Remote controller air flow	–
SW10-2		SW10-3	ON	Remote controller air flow	1 speed
(J10)	ON	(J11)	OFF	Remote controller air flow	2 speed
			ON	Remote controller air flow	3 speed

- 10 -