4
Error display : | e34 |
| [Open phase at L3 phase of 52C secondary side] (Only case of 301~601 type) |
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Indoor unit |
|
|
| Outdoor unit |
|
|
|
| |||||
Red LED |
| Stays OFF |
| Red LED |
| 1 time flash |
|
|
| |||||
Green LED |
| Keeps flashing |
| Green LED |
| Keeps flashing |
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
| Notes (1) | Also check if there is voltage at the L3 phase on the 52C primary | ||
52C | (1) | YES |
|
|
|
|
| side, but no voltage on the secondary side (coil wire disconnec- | ||||||
|
|
|
|
|
|
|
|
| ||||||
secondary side L3 phase |
| Repair |
| tion or faulty contacts). |
| |||||||||
|
|
|
| |||||||||||
open? |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| (2) | If there is voltage at the L3 phase on the 52C primary side and it | ||||
|
|
|
|
|
|
|
|
|
|
| ||||
| NO |
| (2) |
|
|
| is not abnormal, the outdoor unit control PCB is faulty. |
| ||||||
The outdoor unit control PCB is faulty. |
|
|
|
|
|
|
|
| ||||||
(The CT circuit is faulty) |
|
|
| Replace |
|
|
| AAAAAAAAAAAAAAAAAAAAAAAA | ||||||
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
| AAA | If the unit is operated with the service valve closed, 49C (internal ther- | AAA | ||
|
|
|
|
|
|
|
|
|
|
|
| |||
mostat) operates. E34 may also be displayed. Check the service valve.
AAAAAAAAAAAAAAAAAAAAAAAA
5
Error display : e35
[Cooling overload operation]
| Indoor unit |
| Outdoor unit | |
Red LED | Stays OFF | Red LED |
| 1 time flash |
Green LED | Keeps flashing | Green LED |
| Keeps flashing |
Note (1) The green LED in the outdoor unit is used in the FDCA301 ~ 601 models only.
Are the | YES |
|
|
|
|
|
| |
characteristics of the |
|
| Is there cooling overload | |||||
outdoor heat exchanger thermistor |
|
|
|
| operation? | |||
normal? |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
NO |
|
|
|
|
|
|
|
|
Replace the outdoor heat |
|
|
|
|
|
|
|
|
|
|
|
| Is high pressure control | ||||
exchanger thermistor. |
|
|
|
| ||||
|
|
|
| normal? | ||||
|
|
|
|
| ||||
Is the unit normal? |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| Abnormal temperature detection | |||
NO |
|
|
|
| Is it (the actual measurement) correct? | |||
|
|
|
|
|
|
|
| |
Abnormal Temperature Detection |
|
|
|
|
| NO | ||
|
|
|
|
|
| |||
|
| The outdoor control PCB | ||||||
|
|
|
|
| ||||
Error stop |
|
|
|
| is faulty. |
| Replace | |
|
|
|
|
| ||||
Return
Check the unit side.
•Is there a short circuit in the outdoor unit?
•Is the installation space proper?
•Is the refrigerant level too high?
• Is the heat exchanger dirty or clogged?
(1) The compressor’s speed drops when all the following conditions are met (151~251). In the case of the 301~601, expansion valve control is performed.
1Outdoor heat exchanger temperature: A˚C or higher
2Outdoor air temperature: 41ºC or higher
3The outdoor unit’s fan runs at 7 speed (UHi)(1) continuously for 30 seconds or longer.
(2)Control is cancelled when the temperature drops to BºC or lower.
Model |
| Item | A | B |
|
| |||
| Compressor | less than 88 | 58.5 | 53.5 |
|
|
|
| |
151~251 type | speed 88 to less than 108 | 53.5 | 48.5 | |
| (rps) | 108 or higher | 48.5 | 43.5 |
|
| |||
301~601 type |
|
| 58 | 53 |
Note (1) Values in ( ) show for the case of the 301~601 models.
48 | 65(1) |
|
| |
Compressor speed | Indoor heat exchanger | |||
Outdoor air temp. (ºC) | ||||
(rps) | temprature (˚C) | |||
|
| |||
Note (1) In the case of the 151 ~ | less than 88 | 65 or more | |
251, the abnormal stop | |||
|
| ||
temperature differs | 88 to less than 108 | 60 or more | |
depending on the | 108 or higher | 55 or more | |
compressor’s speed. | |||
|
| ||
|
|
●Display Conditions If the outdoor heat exchanger temperature becomes 65ºC 5 times within 60 minutes, including while the compressor is stopped, or if it continues at that temperature for 10 minutes or longer.
Resistance(kΩ)
15
10
5
Outdoor unit heat exchanger themistor
5kΩ at 25°C
0 10 20 30 40 50 Temperature (°C)
- 27 -
