Contents | Husqvarna ProFlex 18 specs

CONTENTS

Operator’s Manual for

Rider ProFlex 18

Introduction	2
Driving and transport on public roads	2
Towing	2
Use	2
Serial number	3
Explanation of symbols	4
Safety instructions	5
General use	5
Driving on slopes	7
Children	8
Maintenance	8
Transport	10
Presentation	11
Location of the controls	11
Throttle control	12
Choke lever	12
Speed limiter	12
Cutting unit	13
Lift lever for cutting unit	13
Lever for adjustment of cutting height	14
Parking brake	14
Seat	14
Fuelling	14
Driving	15
Before starting	15
Starting the engine	15
Driving the machine	16
Cutting tips	18
Stopping the engine	19
Disengage lever	19
Maintenance	20
Maintenance schedule	20
Dismantling of the machine hoods	22
Checking the engine’s cooling air intake	23
Checking the transmission’s air intake	23
Checking and adjusting the steering wires ....	24
Checking and adjustment of throttle wire	25
Checking and adjustment of throttle wire	25

IMPORTANT INFORMATION

Read through these instructions carefully so that you know how to use and maintain the machine before using it.

For servicing other than described in this manual contact an authorised dealer for parts and service.

Adjusting the hydrostatic wire	26
Adjusting the brakes	27
Checking the tyre pressure	27
Replacement of air filter	28
Replacement of fuel filter	29
Cleaning the pulse air filter	29
Checking the fuel pump’s air filter	29
Checking the battery acid level	30
Ignition system	30
Checking the safety system	31
The parts of the cutting unit	32
Fitting the cutting unit	32
Setting the parallelism	34
Setting the cutting height	34
Checking and adjusting the ground
pressure	35
Replacing the break-pin (BioClip)	35
Service position for the cutting unit	36
Checking the blades	36
Dismantling the cutting unit	37
Removing the attachment frame	39
Dismantling the belts	39
Assembling the belts	40
Changing the cutting unit’s belts	41
Removal of BioClip plug	43
Cutting unit models	43
Lubrication	44
Lubrication chart	44
General lubrication	45
Lubricating wires	45
Lubrication instructions according to chart ....	45
Trouble shooting schedule	50
Storage	51
Winter storage	51
Service	51
Wiring diagram	52
Technical data	53
EU declaration of conformity	55
Service journal	56

English – 1

Image 3

Husqvarna ProFlex 18 manual Contents

Contents

English Rider ProFlex Svenska Contents Towing InstructionDear customer Travel and transport on public roads Safety Instructions Good serviceSerial number Read the instructions Explanation of Symbols General use Safety instructions Keep children away from the area to be mowed Proceed as follows Driving on slopes Children Maintenance Do not smoke when carrying out maintenance Never run the machine in an enclosed area Transport Presentation PresentationLocation of the controls Speed of the machine is steplessly regulated Throttle controlChoke lever Speed limiter Lift lever for cutting unit Cutting unit Fuelling Lever for adjustment of the cutting heightParking brake Seat Driving Before startingStarting the engine Driving the machine 6007-210 MAX Cutting tips Disengage lever Stopping the engine Maintenance Maintenance scheduleYear Year 100 300 Hours Before after Right-hand fender Dismantling of the machine hoodsEngine hood Nose Transmission cover Check the engine’s cooling air intakeCheck the transmission’s air intake Left-hand fender Checking and adjustment of the steering wires Checking and adjusting the choke wire Checking and adjustment of the throttle wire Adjusting the hydrostatic wire Adjusting the brakes Poorly adjusted brakes can result in reduced braking powerChecking the tyre pressure Replacing the air filter Replacement of the fuel filter Cleaning the pulse air filterChecking of the fuel pump’s air filter Check the level of the battery acid Procedures on contact with acidFitting the wrong spark plug type can damage the engine Inspecting the safety system Take care. Risk of crushing injury Fitting the cutting unit Belt diagram Watch your fingers. Do not turn the blades or beltCheck that the belt is fitted around the tension roller Cutting height Parallelism Replacing the break-pin BioClip Checking the blades Service position for the cutting unitPlacing in the service position Releasing from the service position Dismantling the cutting unit 8009-169 Dismantling the belt Removing the attachment frame Assembling the belt Replacing the cutting unit’s belts Belt replacement on BioClip Belt replacement on BioClip112 Cutting unit models Removal of BioClip plug Combi Lubrication Lubrication chart Lubricating wires GeneralPedal mechanism in frame tunnel Engine oil Chains in frame tunnel Transmission Gear lever Throttle and choke wires, lever bearings Triangular linkDriver’s seat Transmission oil level Oil filter, replacementParking brake wire Belt tensioner Problem Procedure Trouble Shooting Schedule Service StorageWinter storage Wiring Diagram Rider ProFlex Technical Data Rear ejector BioClip Rear ejector Combi EU declaration of conformity Only applies to Europe EU-DECLARATION of Conformity Work done ServicejournalPre-delivery service After first 8 hours Hour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´+H%,¶6c¨ English 114 00