Servicejournal, Pre-delivery service | Husqvarna ProFlex 18 specs

SERVICEJOURNAL

Work done

Pre-delivery service

1.	Top up battery with acid and recharge for four hours.
2.	Fit steering wheel, seat and any optional equipment.
3.	Fit cutting unit.
4.	Adjust cutting unit:
	Adjust lift springs (effective weight of cutting unit should be
	12–15 kg, or set to maximum lift if brush is to be fitted).
	Adjust cutting unit so that rear edge is about 2–4 mm higher
	than front edge.
	Adjust cutting unit height setting so that cutting height limit is
	5 mm above the frame of the unit at the lowest cutting height.
5.	Check that the oil levels in the engine and transmission are
	correct.
6.	Check and adjust tyre pressure (60 kPa, 0.6 bar).
7.	Connect battery.
8.	Fill with fuel and start engine.
9.	Check that machine does not move in neutral.
10. Check:
	Forward drive.
	Reverse drive.
	Operation of blades.
	Seat safety switch.
	Lift lever safety switch.
	Safety switch for the hydrostat pedals.
11. Check engine revs 3,000 ±75 rpm.
12. Tell customer about:		Pre-delivery service carried out.
	Need and benefits of following the service schedule.	No outstanding problems.
	Need and benefits of following the service schedule.
	Need and benefits of having machine serviced every 300	Certified:
	Need and benefits of having machine serviced every 300
	hours.
	Servicing and the influence of this journal on the second-hand
	value of the machine.
	Range of applications for BioClip.
13. Complete proof of sale, etc.

After first 8 hours		Date, mileage, stamp, sign
After first 8 hours
1.	Change engine oil.

56 – English

Image 58

Husqvarna ProFlex 18 Servicejournal, Pre-delivery service, After first 8 hours, Work done, Date, mileage, stamp, sign

Contents

Rider ProFlex English Svenska Contents Travel and transport on public roads InstructionDear customer Towing Good service Safety InstructionsSerial number Explanation of Symbols Read the instructions Safety instructions General use Keep children away from the area to be mowed Driving on slopes Proceed as follows Maintenance Children Do not smoke when carrying out maintenance Transport Never run the machine in an enclosed area Presentation PresentationLocation of the controls Speed limiter Throttle controlChoke lever Speed of the machine is steplessly regulated Cutting unit Lift lever for cutting unit Seat Lever for adjustment of the cutting heightParking brake Fuelling Before starting DrivingStarting the engine Driving the machine 6007-210 Cutting tips MAX Stopping the engine Disengage lever Maintenance schedule MaintenanceYear Hours Before after Year 100 300 Nose Dismantling of the machine hoodsEngine hood Right-hand fender Left-hand fender Check the engine’s cooling air intakeCheck the transmission’s air intake Transmission cover Checking and adjustment of the steering wires Checking and adjustment of the throttle wire Checking and adjusting the choke wire Adjusting the hydrostatic wire Poorly adjusted brakes can result in reduced braking power Adjusting the brakesChecking the tyre pressure Replacing the air filter Cleaning the pulse air filter Replacement of the fuel filterChecking of the fuel pump’s air filter Procedures on contact with acid Check the level of the battery acidFitting the wrong spark plug type can damage the engine Inspecting the safety system Fitting the cutting unit Take care. Risk of crushing injury Watch your fingers. Do not turn the blades or belt Belt diagramCheck that the belt is fitted around the tension roller Parallelism Cutting height Replacing the break-pin BioClip Releasing from the service position Service position for the cutting unitPlacing in the service position Checking the blades Dismantling the cutting unit 8009-169 Removing the attachment frame Dismantling the belt Assembling the belt Belt replacement on BioClip Replacing the cutting unit’s belts Belt replacement on BioClip112 Removal of BioClip plug Combi Cutting unit models Lubrication chart Lubrication General Lubricating wiresPedal mechanism in frame tunnel Chains in frame tunnel Engine oil Gear lever Transmission Triangular link Throttle and choke wires, lever bearingsDriver’s seat Belt tensioner Oil filter, replacementParking brake wire Transmission oil level Trouble Shooting Schedule Problem Procedure Storage ServiceWinter storage Wiring Diagram Technical Data Rider ProFlex Rear ejector Combi Rear ejector BioClip EU-DECLARATION of Conformity EU declaration of conformity Only applies to Europe After first 8 hours ServicejournalPre-delivery service Work done Hour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´+H%,¶6c¨ English 114 00