Power Supply Cable Connector Specifications | IBM 2169 instruction

Power Supply Cable Connector Specifications

Refer to the following figures when checking for voltages on power supply cable connectors.

When checking voltages, the power supply fan must be running. To power on the power supply without using the on/off switch, use a screwdriver or other tools to short the power supply connector (with the switch cable disconnected from the connector on the system board) or use a connection (jumper) to short the black and green wires of the 20-pin connector on power supply.

20

11

10

1

System Board Power Supply Connectors

129

Image 131

IBM 2169 manual Power Supply Cable Connector Specifications

Contents

Hardware Maintenance Manual for Service Level a First Edition July Contents 152 110140 143 Voltage Supply Switch Settings Page To Connect To Disconnect Do not Page Perigo Para Conectar Para Desconectar Não Cuidado Perigo Page Page Page Page Page Débranchez tous les Commencez pasDébranchez les câbles Branchez les cordons Dinterface des prisesPage Page Vorsicht Achtung Kabel anschließen Kabel lösenPage Vorsicht Per collegare Per scollegare Pericolo Attenzione Quando è installata ununità CD-ROM, notare quanto segue ≥32 Kg ≥55Kg Page Page Page Instrucciones de conexión Desconexión Peligro Lo que no debe hacer Peligro Laser Compliance Statement IBM Trademarks Preface General Information Memory IntroductionProduct Overview Processors Multimedia Power ManagementDiskette Drive CD-ROM Drive Keyboard Power SupplyInternal Cabling Modem Not all models Interface Hardware Interfaces USB Flash Bios Update Procedure MTM BIOS-contained Model Number and Serial Number Working with the Setup Menus Starting the Setup Utility Bios Setup Utility Keys Function Standard Cmos Features Option Halt On Advanced Bios Features Setup OptionQuick Power On Self Test Video Boot Up NumLock Status First/Second/Third Boot DeviceBoot Other Device Boot Up Floppy Seek Report No Diskette Drive for Win Typematic Rate Chars/SecSecurity Option OS Select For Dram 64 MB Advanced Chipset Features Option Integrated Peripherals Option UR2 Duplex Mode DefaultL Half Hardware ResetIDE HDD Block Mode Uart Mode Select Pwron After PWR-Fail Parallel Port ModeECP Mode Use DMA Default Midi Port IRQ Default Power Management Setup Option Suspend Type Suspend ModeHDD Power Down Power On by Ring CPU Thermal-Throttling Resume by AlarmCPU Thermal Limit Board Thermal LimitPage PCI/VGA Palette Snoop PNP/PCI Configuration OptionReset Configuration Data Resources Controlled By Frequency Control Option PCI Health Status Option Load Fail Safe Defaults Option Load Optimized Defaults Option Exit Without Saving Option Set Supervisor and User PasswordsSave And Exit Setup Option Erasing a lost or forgotten password clearing Cmos Specifications Operating Requirements Special Tools CheckProcedures Introduction Start Product Recovery Program menuIBM PC Enhanced Diagnostics Enhanced Diagnostics download or diskette PC-Doctor’s Diagnostic SoftwareIBM PC Enhanced Memory Diagnostics Please Read the Following Page 007 005 009 Index of Symptoms, Messages, Error Codes, or Beeps Action/FRU Post Error Codes and Messages Floppy Disks Action/FRU Device. Then reboot the system Action/FRU Beeps System Board Error Symptoms Action/FRU ProcessorPage Hard Disk Drive Error Symptoms Action/FRU CD-ROM Drive Real-Time Clock Parallel Diagnostics programs Other Problems Page 003 Factory-Installed Storage Devices 005 Page 002 Factory-Installed Modem Card Start Modem adapter functions normally End Audio Not Supported by Diagnostics Program 008 004006 Memory Start CD-ROM Drive Start Keyboard Start Mouse Start 011 010 Power Supply Start Page Replace the on/off switch cable assembly Monitor Is the Screen READABLE? YES, Read AHEAD. NO, GO to Step Undetermined Problems 105 Diagnostic Aids Introduction Power-On Self Test Diagnostics Tools Performing a partial or full recovery Submenu Selections Diagnostics Program FeaturesPage Repair Information Removals and Replacements of machine type Identifying the Parts of the System Unit Page Top Cover Adapter Cards Installing Adapter Cards Removing Adapter Cards Diskette Drive To remove CD-ROM Drive Hard Disk Drive System Board Memory Dimm 122 Parts/Test Point Locations Introduction Layout of system board of the machine type Component Description FP1 LED2 Sense Pins polarity is marked on the pcb next to each pin Function Pins Replacing the system battery Power Supply Cable Connector Specifications Pin Function Color Main Output Pin AssignmentPage Factory-Installed Modem Card Connector Functions Connect to… Factory-Installed Modem Card Layout Hard Disk Quantum Jumper Settings Locations In. Hard Disk Drive Jumper Locations & Settings CD-ROM Emergency-exit Function Connect to… CD-ROM Drive Rear Panel Connectors and FeaturesCD-ROM Drive Jumper Settings Dimm Configurations Parallel Port Signals Pin Signal Name Serial Port Signals Pin Signal Name Keyboard Port Signals Pin Signal Name Mouse Port Signals Pin Signal Name Diskette Drive Cable Connector Signals Pin Signal Name IDE Cable Connector Signals Pin Signal Name 141 Safety Inspection Guide General Guidelines Page Parts Catalog Part Catalog of machine type Assembly 1 System Unit Asm-Index FRU Number Description 14F0032 Power Cord UK/HK/Singapore Not Shown Page FRU Number Description Assembly 3 CD-ROM, Modem Card 60H6027 Modem Phone Cable Adapter Denmark Assembly 4 Keyboard and Mouse Palm Rest Hungarian Appendix A. Online Support Information Index Bios Check Procedure, 99 ctor Specifications, 125 Error Symptoms