Manuals / IBM / Computer Equipment / Computer Drive

IBM DCS9550 1S1 manual Safety Guidelines, The enclosure MUST be grounded before applying power

Models: DCS9550 1S1

1 79

Download 79 pages 24.28 Kb

Page 5

Safety Guidelines

P r e f a c e

Safety Guidelines

Caution ! If this product is used in a manner not specified by the manufacturer, the protection provided by the product may be impaired.

!The enclosure MUST be grounded before applying power.

Warning

!Unplug the product if you think that it has become damaged in any way and before you move it.

Warning

Caution ! Plug-in modules are part of the fire enclosure and must only be removed when a replacement can be immediately added. The system must not be run without all units in place. Operate the system with the enclosure top cover closed and blanking plates fitted where modules are missing.

To comply with applicable safety, emission, and thermal requirements, keep all enclosure covers securely fitted and keep all bays fitted with plug-in modules.

Enclosures must be only operated from a power supply input voltage range of 100 V AC to 240 V AC.When a redundant power input module is fitted, it must be operated from a reduced input voltage range of 200 V AC to 240 V AC.

The plug on the power supply cord is used as the main disconnect device. Ensure that the socket outlets are located near the product and are easily accessible.

The product is intended to operate with three working Plus. Before removal/replacement of any module disconnect all supply power for complete isolation.

To ensure protection against electric shock caused by HIGH

!LEAKAGE CURRENT (TOUCH CURRENT), the enclosure must be connected to at least two separate and independent

Warning sources. This should ensure a reliable earth connection

IBM System Storage DCS9550 1S1 Storage Expansion Unit Installation, Service, and User Guide

iii

Image 5

IBM DCS9550 1S1 manual Safety Guidelines, The enclosure MUST be grounded before applying power

Contents

SC30-9738-00 IBM System StoragePage Preface Getting information, help, and serviceWhat is in this guide Using the documentationSafe Handling International StandardsQualified Personnel The enclosure MUST be grounded before applying power Safety GuidelinesProvide a safe electrical earth ground connection for the power cord Operation of the product with ANY modules MISSING in the Electronic Emission Notices Class 1 Laser ProductFederal Communications Commission FCC Class A Statement European Union EU Electromagnetic Compatibility DirectiveJapan VCCI Class A ITE Electronic Emission Statement Taiwan Class A Electronic Emission StatementIndustry Canada Class A Emission Compliance Statement Avis de conformité à la réglementation d’Industrie CanadaESD Precautions Rack System PrecautionsKorean Class A Electronic Emission Statement Data SecurityTaiwan Contact Information How to Send Your Comments P r e f a c e P r e f a c e Contents The IBM System Storage DCS9550 1S1 Storage Expansion UnitDimensions WeightSystem Faults Audible Alarm MutePower Supply/Cooling Faults Thermal Alarm1.1 The IBM System Storage DCS9550 1S1 Storage Expansion Unit Introduction1.1.1 Enclosure Chassis 1.2 The Plug-in Modules 1.2.1 Power Supply/Cooling Module1.2.1.1 Multiple Power Supply/Cooling Modules 1.2.2 Operators Panel 1.2.2.1 Ops Panel Indicators and SwitchesSwitch Number Recommended SettingUnitSCM usage at 2Gb/s 1.2.3 SCM Input/Output ModuleSee Sw Mode 3 not supportedFlashing Introduction Figure 1-7 SCM Front Panel as viewed from rear of Enclosure1.2.4.1 SATA Dual Path Transition Card 1.2.4.2 Drive Status Indicators1.2.4 Drive Carrier Module 1.2.4.3 Anti-tamper Locks 1.3 Visible and Audible Alarms1.2.5 Dummy Carrier Modules 1.2.6 Blank Modules1.4.1 Dimensions 1.4 DCS9550 1S1 Storage Expansion Unit Technical Specification1.4.2 Weight 1.4.3 AC Power 450W PSU1.4.6 Environment 1.4.7 Interfaces 1.4.8 SCM I/O Module Specification1.4.9 Drive Carrier Module Specification Introduction 1.4.10 Software Enclosure Services SES SupportEnclosure temperature Fan speed Drive condition Operator panel status Introduction This page is intentionally blank2.1 Planning Your Installation InstallationDrive carrier modules 0 & 15 provide SES Management Services Power Supplyintegral part of chassis assembly. Installed in rear Bay Install in rear Bay2.1.1 Enclosure Bay Numbering Convention Blank SCM I/O2.2.3 Chassis Installation 2.2.3.1 Parts Check List 2.2 Enclosure Installation Procedures2.2.1 Pre-Requisites 2.2.2 Rack Mounting Rail Kit2.3 Power Supply/Cooling Module Installation 2.2.3.2 Procedure2.3.2 Power Supply/Cooling Module Procedure 2.3.1 Parts Check ListFigure 2-3 Installing an AC Power Supply Cooling Module Figure 2-2 AC Power Supply/Cooling Module - Handle in Open Position2.4.1 Internal Loop Structures 2.4 SCM I/O Module Configurations2.5 FC-AL Interface Figure 2-4 Installing an AC Power Supply Cooling ModuleInstallation 2.6 Cabling the IBM System Storage DCS9550 1S1 Storage Expansion UnitUnit 1-A Unit 1-BUnit 2- A InstallationUnit 2- B Unit 2- C2.7.1 Procedure 2.7 SCM I/O Module InstallationSetting Switch2.8 Drive Enclosure Device Addressing FunctionWheel ThumbSwitch Setting2.9.1 Planning and Configuring Your Installation 2.9 Drive Carrier Configuration2.9.1.1 System Configuration 2.9.1.2 Drive Configuration2.10.2 Procedure 2.10 Drive Carrier Installation 2.10.1 Parts Check ListInstallation Figure 2-10 Installing a SATA Drive Carrier ModuleFigure 2-11 Installing a SATA Drive Carrier Module 2.10.4 Engaging the Anti-tamper Locks 2.10.3 Dummy Carrier Modules2.10.4.1 Activating the Locks Drives are supplied with the locks set in the locked position2.11.2 Procedure 2.11 Power Cord Connection 2.11.1 Parts Check List2.12 Grounding Checks This page is intentionally blank InstallationOperation 3.1 Power OnFan Fault 3.1.1 Power Supply/Cooling Module LEDsAC PSU PSU GoodPower On FaultSystem Fault Fault3.3 Starting the Drives 3.4 Power Down3.3.1 Disk Drives LEDs 2Gb Link4.1 Emulation Limitations Troubleshooting and Problem Solving4.2 Initial Start-up Problems 4.2.1 Faulty Cords 4.2.3 Green “Signal Good” LED on SCM Not Lit 4.2.2 Alarm Sounds On Power Up4.3.1 Power Supply/Cooling Module 4.3 LEDsStatus 4.3.2 Ops PanelFan Fault AC PSUDefinition FaultColor Normal4.4.1 Audible Alarm Mute 4.4 Audible Alarm4.3.3 SCM I/O Module LEDs Definition4.5.1 System Faults 4.5 Troubleshooting4.5.2 Power Supply/Cooling Faults SymptomSymptom 4.5.3 Thermal ControlCause Action4.6 Drive Carrier Module Faults 4.5.4 Thermal Alarm4.5.5 Thermal Shutdown State4.8 Continuous Operation During Replacement 4.7 Dealing with Hardware Faults4.6.1 Dummy Carrier Modules 4.9 Replacing a Module4.9.1.2 Inserting the Module 4.9.1 Power Supply/Cooling Modules4.9.1.1 Removing a Power Supply/Cooling Module Troubleshooting and Problem Solving Figure 4-2 Removing/Inserting an AC Power Supply/Cooling ModuleFigure 4-3 Removing/Inserting an AC Power Supply/Cooling Module 4.9.3.1 Removing the Module 4.9.2 Ops Panel4.9.3 SCM I/O Module Figure 4-6 Removing an SCM I/O Module Troubleshooting and Problem SolvingFigure 4-5 Removing an SCM I/O Module 4.9.4 Drive Carrier Module 4.9.4.1 Removal and Replacement4.9.3.2 Inserting the Module IBM MTM 1269-1S1 SATA Disk Chassis FRUs 4.10 Spare Parts and Ancillary ItemsThis page is intentionally blank Troubleshooting and Problem SolvingGlossary Initialize To prepare a hardware device for use Index starting drives SYSTEM LED Visible and Audible AlarmsSerial ATA Control SCM Input/Output module serial ATA protocol 20 SES Armonk, N.Y U.S.A NoticesIBM Director of Licensing IBM Corporation North Castle Drive Product recycling and disposal Trademarksof life per this Directive Page Publication No. SC30-9738-00 Readers’ Comments - We’d Like to Hear from YouIBM System Storage Readers’ Comments - We’d Like to Hear from You BUSINESS REPLY MAILPlease do not staple Please do not staplePage SC30-9738-00