Other communications- other countries | Icom IC-R20 guide

FREQUENCY TABLE 13

■Other communications— other countries

DLPD (Low Power Device) channels

(unit: MHz)

DPMR446 channels (unit: MHz)

CH

Frequency

1433.075

2433.100

3433.125

4433.150

5433.175

6433.200

7433.225

8433.250

9433.275

10433.300

11433.325

12433.350

13433.375

14433.400

15433.425

16433.450

17433.475

18433.500

19433.525

20433.550

21433.575

22433.600

23433.625

24433.650

25433.675

26433.700

27433.725

28433.750

29433.775

CH

Frequency

30433.800

31433.825

32433.850

33433.875

34433.900

35433.925

36433.950

37433.975

38434.000

39434.025

40434.050

41434.075

42434.100

43434.125

44434.150

45434.175

46434.200

47434.225

48434.250

49434.275

50434.300

51434.325

52434.350

53434.375

54434.400

55434.425

56434.450

57434.475

58434.500

CH

Frequency

59434.525

60434.550

61434.575

62434.600

63434.625

64434.650

65434.675

66434.700

67434.725

68434.750

69434.775

CH	Frequency

1	446.00625
2	446.01875
3	446.03125
4	446.04375
5	446.05625
6	446.06875
7	446.08125
8	446.09375

13

76

Image 89

Icom IC-R20 Other communications- other countries, PMR446 channels unit MHz, LPD Low Power Device channels Unit MHz

Contents

IR20 Auto write and 50 scan edge channels are included Some frequency bands are inhibited according to versionMay occur Equipment damage may occur Operate this device under FCC regulations Precaution Supplied Accessories Table of Contents Battery pack installation Batteries installationQuick Reference Guide Preparations Swivel belt clip Option Belt clip Third-party antennas may in- crease receiver performance Antenna About default setting Charging the batteryYour ﬁrst scanning Experience Adjusting squelch level Adjusting audio levelBasic operation Turning on the receiver Receive mode selection Setting frequencyMemory programming Selecting a memory channel Programming scan edges Writing a memory channel Programmed scan operationSelecting a scan edge channel B Selecting a scan edge channel a Cancelling scan Starting scan Select VFO modeStarting scan Selecting a scanning type Front, top and side panels Panel Description ULEFT Dial L-DIAL EPOWER KEY PowerIRIGHT Dial R-DIAL QDUALWATCH/CLEAR KEY Dualwatch MODE/SCAN KEY Mode Scan Or 10 MHz tuning steps pVOLUME/DIAL KEY 1 DIAL.SEL VFO/MHz KEY VFO MHz Inputs digit ‘5’ for frequency input, memory Push for 1 sec. to enter the set modeInputs digit ‘0’ for frequency input, memory Inputs digit ‘8’ for frequency input, memory @2STOP/PLAY ≈ WDUPLEX Indicators p QBATTERY IndicatorESIGNAL Squelch Indicators Function display TLOCK Indicator p RANL/NB Indicator pgsYAFC Indicator p USKIP Indicators p Battery installation Battery INSTALLATION/CHARGING Battery caution Battery chargingRegular charging Charging caution Rapid charging with the BC-156 CP-18A/E fuse replacement Mode selection Frequency and Channel SettingVFO mode Memory mode/PreSet*/TV*/Weather† channels Operating band selection Available frequency bands 2425 Setting a frequency Setting a tuning stepTuning step selection Using the dial Editting MHz to 1260.240 MHz Using the keypadFrequency can be directly set via numeral keys Lock function Receive mode selection When a signal is received Setting audio volumeBasic Operation Receiving Push and hold SQL to monitor the operating frequency Squelch level settingMonitor function RF gain Attenuator function Rotate R-DIALto select Duplex SettingDuplex operation NB/ANL function AFC function Select the sweep steps, if desired Band scope Single band operation Dial function assignment Operating bands table for dualwatch operation Main band selection Band exchange Lower band’s squelch adjustment Setting audio volume Squelch level setting Memory Channels Memory channel contentsGeneral description Memory channel programming Push MR S.MW for 1 sec. to set the channel into the bank Memory bank setting Rotate R-DIALto select the bank channel Memory bank selection Rotate R-DIALto select the desired character Programming memory/bank name Dication type from bank name or memory name Selecting memory/bank name IndicationAvailable characters Copying memory contents Memory clearing Push MR S.MW for 1 sec. to clear the contents Erasing/transferring bank contents Scan types Scan OperationFull Scan p FREQUENCY/MEMORY Skip Function p Full/band/programmed scan Select VFO mode with VFO MHzTo start the scan, release Mode Scan Scan edges programming Release Mode Scan to start the selected scan Select memory mode with MR S.MWMemory/bank/all bank scan To stop the scan, push Dualwatch During auto-memory write scanning Auto-memory write scanRecalling the stored frequencies Clearing the stored frequencies Skip channel/frequency setting Push Dualwatch to exit set mode Scan pause timerScan resume condition SET Scan resume timer About priority beep function Priority WatchPriority watch types Push Dualwatch to cancel the watch Push Dualwatch to exit set mode and start the watchPriority watch operation Select the desired memory channel While scanning memory/bank channels VFO scan watch qSelect memory mode0Push Dualwatch to cancel the watch and scan Push Dualwatch to stop the beeps and blinking man- ually Comfortable ReceivingTone/DTCS squelch operation Available Dtcs code list Tone squelch frequency/DTCS code settingPush 8 SET Available tone frequency list Dtcs polarity setting Push 4 T-SCANfor 1 sec. to start the tone scan Tone scan General SET ModeExpanded set mode ON/OFF General set mode items Set mode itemsExpanded set mode items Key-touch beep Priority watchBeep output level Display backlighting Noise blanker Power saveANL function AF ﬁlter Power and Lock No accessible key is available, exceptAM antenna selection FM antenna selection Default Auto power OFFDial speed acceleration Monitor key action Scan resume timer Scan pause timerScan stop beep Turns the scan stop beep function on and OFF Offset frequency Scope audio outputDuplex direction Sets the audio output function while scope operation Dtcs code Tone frequencyDtcs polarity Available subaudible tone frequencies Memory bank link LCD contrast can be adjusted through 15 levelsLCD contrast Turns weather alert function on and OFF CI-V transceive CI-V addressCI-V baud rate Other Functions RPush Dualwatch to exit set modeAntenna selection Selecting antenna Weather channel operation Turn the weather alert function OFF in set modeWeather channel selection Weather alert function Receiver shows following indications Cloning using a personal computerData cloning Cloning error Auto power-off function Recording a received audio Playing back recorded contentIC recorder Recording set mode Quality setting Playback speed setting Erasing recorded audio Automatic recordingREC Same time, but cannot erase each track independently Partial reset Data format Control CommandCommand table CI-V compatible transceiver Control Command TV channels Frequency TableS.A. channels Ccir channels New China channelsZealand Channels Italian channels Indonesian channelsTaiwan channels FOT channels Weather channelsunit MHz VHF marine channels HF CB Citizens Band channels Other communications in the USAChannels Murs channels Cable TV IRC Wireless MicrophonesGeneral aviation frequencies PMR446 channels unit MHz LPD Low Power Device channels Unit MHzOther communications- other countries UHF C.R.S Citizen Radio Service channels Troubleshooting Maintenance General Specifications Options Options For Microsoft Windows XP Driver Installation Driver Installation Windows starts installing the USB driver 0Repeat step e to y After the installation is completed, click Finish Found New Hardware Wizard will come up as below. Click Next For Microsoft Windows2After clicking Finish, the dialog appears as below Select Click Driver Installation For Microsoft Windows 98/98SE/Me Select Click COM port conﬁrmation Click the Device Manager IR20 Pocket Guide Release Mode Scan to start scan We Icom Inc. Japan Declaration Conformity Kamiminami, Hirano-ku, Osaka 547-0003, Japan #07 France