For Microsoft Windows | Icom IC-R20 specs

17 DRIVER INSTALLATION

!1The following screen appears when the installation is com- pleted. Click [Finish] to close the screen.

Click

!2After clicking [Finish], the dialog appears as below.

■For Microsoft® Windows® 2000

qConnect the IC-R20 to the desired USB port using with the USB cable, OPC-1382.

• “Found New Hardware” appears as below.

wThe “Found New Hardware Wizard” will come up as below. Click [Next>].

• Rebooting the PC is recommended.

Click

Page 98

Image 98

Icom IC-R20 instruction manual For Microsoft Windows, 2After clicking Finish, the dialog appears as below

Contents

IR20 May occur Some frequency bands are inhibited according to versionAuto write and 50 scan edge channels are included Equipment damage may occur Precaution Operate this device under FCC regulations Supplied Accessories Table of Contents Quick Reference Guide Batteries installationBattery pack installation Preparations Belt clip Swivel belt clip Option Antenna Third-party antennas may in- crease receiver performance Your ﬁrst scanning Charging the batteryAbout default setting Experience Basic operation Adjusting audio levelAdjusting squelch level Turning on the receiver Memory programming Setting frequencyReceive mode selection Selecting a memory channel Selecting a scan edge channel B Programmed scan operationProgramming scan edges Writing a memory channel Selecting a scan edge channel a Starting scan Starting scan Select VFO modeCancelling scan Selecting a scanning type Panel Description Front, top and side panels IRIGHT Dial R-DIAL EPOWER KEY PowerULEFT Dial L-DIAL QDUALWATCH/CLEAR KEY Dualwatch VOLUME/DIAL KEY 1 DIAL.SEL Or 10 MHz tuning steps pMODE/SCAN KEY Mode Scan VFO/MHz KEY VFO MHz Inputs digit ‘0’ for frequency input, memory Push for 1 sec. to enter the set modeInputs digit ‘5’ for frequency input, memory Inputs digit ‘8’ for frequency input, memory @2STOP/PLAY ≈ ESIGNAL Squelch Indicators QBATTERY IndicatorWDUPLEX Indicators p Function display YAFC Indicator p RANL/NB Indicator pgsTLOCK Indicator p USKIP Indicators p Battery INSTALLATION/CHARGING Battery installation Regular charging Battery chargingBattery caution Charging caution CP-18A/E fuse replacement Rapid charging with the BC-156 VFO mode Frequency and Channel SettingMode selection Memory mode/PreSet*/TV*/Weather† channels Operating band selection 2425 Available frequency bands Tuning step selection Setting a tuning stepSetting a frequency Using the dial Editting MHz to 1260.240 MHz Using the keypadFrequency can be directly set via numeral keys Receive mode selection Lock function Basic Operation Setting audio volumeWhen a signal is received Receiving Push and hold SQL to monitor the operating frequency Squelch level settingMonitor function Attenuator function RF gain Rotate R-DIALto select Duplex SettingDuplex operation AFC function NB/ANL function Band scope Select the sweep steps, if desired Dial function assignment Single band operation Main band selection Band exchange Operating bands table for dualwatch operation Setting audio volume Squelch level setting Lower band’s squelch adjustment General description Memory channel contentsMemory Channels Memory channel programming Memory bank setting Push MR S.MW for 1 sec. to set the channel into the bank Memory bank selection Rotate R-DIALto select the bank channel Programming memory/bank name Rotate R-DIALto select the desired character Dication type from bank name or memory name Selecting memory/bank name IndicationAvailable characters Copying memory contents Push MR S.MW for 1 sec. to clear the contents Memory clearing Erasing/transferring bank contents Full Scan p Scan OperationScan types FREQUENCY/MEMORY Skip Function p Full/band/programmed scan Select VFO mode with VFO MHzTo start the scan, release Mode Scan Scan edges programming Memory/bank/all bank scan Select memory mode with MR S.MWRelease Mode Scan to start the selected scan To stop the scan, push Dualwatch Recalling the stored frequencies Auto-memory write scanDuring auto-memory write scanning Clearing the stored frequencies Skip channel/frequency setting Scan resume condition Scan pause timerPush Dualwatch to exit set mode SET Scan resume timer About priority beep function Priority WatchPriority watch types Priority watch operation Push Dualwatch to exit set mode and start the watchPush Dualwatch to cancel the watch Select the desired memory channel While scanning memory/bank channels VFO scan watch qSelect memory mode0Push Dualwatch to cancel the watch and scan Push Dualwatch to stop the beeps and blinking man- ually Comfortable ReceivingTone/DTCS squelch operation Push 8 SET Tone squelch frequency/DTCS code settingAvailable Dtcs code list Available tone frequency list Dtcs polarity setting Tone scan Push 4 T-SCANfor 1 sec. to start the tone scan General SET ModeExpanded set mode ON/OFF General set mode items Set mode itemsExpanded set mode items Beep output level Priority watchKey-touch beep Display backlighting ANL function Power saveNoise blanker AF ﬁlter AM antenna selection No accessible key is available, exceptPower and Lock FM antenna selection Dial speed acceleration Auto power OFFDefault Monitor key action Scan stop beep Scan pause timerScan resume timer Turns the scan stop beep function on and OFF Duplex direction Scope audio outputOffset frequency Sets the audio output function while scope operation Dtcs polarity Tone frequencyDtcs code Available subaudible tone frequencies LCD contrast LCD contrast can be adjusted through 15 levelsMemory bank link Turns weather alert function on and OFF CI-V transceive CI-V addressCI-V baud rate Antenna selection RPush Dualwatch to exit set modeOther Functions Selecting antenna Weather channel selection Turn the weather alert function OFF in set modeWeather channel operation Weather alert function Receiver shows following indications Cloning using a personal computerData cloning Auto power-off function Cloning error Recording a received audio Playing back recorded contentIC recorder Playback speed setting Recording set mode Quality setting REC Automatic recordingErasing recorded audio Same time, but cannot erase each track independently Partial reset Data format Control CommandCommand table Control Command CI-V compatible transceiver S.A. channels Frequency TableTV channels Ccir channels Zealand China channelsNew Channels Taiwan channels Indonesian channelsItalian channels FOT channels VHF marine channels Weather channelsunit MHz HF CB Citizens Band channels Other communications in the USAChannels Murs channels Cable TV IRC Wireless MicrophonesGeneral aviation frequencies PMR446 channels unit MHz LPD Low Power Device channels Unit MHzOther communications- other countries UHF C.R.S Citizen Radio Service channels Maintenance Troubleshooting Specifications General Options Options Driver Installation For Microsoft Windows XP Driver Installation Windows starts installing the USB driver After the installation is completed, click Finish 0Repeat step e to y Found New Hardware Wizard will come up as below. Click Next For Microsoft Windows2After clicking Finish, the dialog appears as below Select Click Driver Installation For Microsoft Windows 98/98SE/Me Select Click COM port conﬁrmation Click the Device Manager Pocket Guide IR20 Release Mode Scan to start scan Declaration Conformity We Icom Inc. Japan #07 France Kamiminami, Hirano-ku, Osaka 547-0003, Japan

Icom IC-R20 For Microsoft Windows, 2After clicking Finish, the dialog appears as below

Models: IC-R20

17 DRIVER INSTALLATION

!2After clicking [Finish], the dialog appears as below.

■For Microsoft® Windows® 2000

wThe “Found New Hardware Wizard” will come up as below. Click [Next>].