Memory bank selection | Icom IC-R20 instruction

■Memory bank selection

qPush [MR S.MW] to select memory mode.

wWhile pushing [BAND], rotate [R-DIAL]to select the de- sired bank (A to Z).

•The bank can also be selected by pushing [BAND] several times.

•Only programmed banks are displayed.

MEMORY CHANNELS 6

eRotate [R-DIAL]to select the bank channel.

•Only programmed channels are displayed.

-DUP TSQL AFC
MODE FM ANL
145 870
PSKIP	6
	6

[R-DIAL]

BAND

MR

S.MW

-DUP TSQL AFC MODE FM ANL

145 870

PSKIP

√µ 001

ATT

Rotate [R-DIAL] while pushing [BAND]

-DUP TSQL AFC MODE AM ANL

118 000

PSKIP

√µ A12

Only the programmed banks appear.

	-DUP TSQL	AFC
MODE FM ANL
	438 720
		PSKIP
√	µ	Y01

√

µ A99

ATT

Bank initial

Bank chanel number

rTo return to regular memory condition, rotate [R-DIAL]while pushing [BAND], or push [BAND] several times.

28

Image 41

Icom IC-R20 instruction manual Memory bank selection, Rotate R-DIALto select the bank channel

Contents

IR20 Auto write and 50 scan edge channels are included Some frequency bands are inhibited according to versionMay occur Equipment damage may occur Operate this device under FCC regulations Precaution Supplied Accessories Table of Contents Battery pack installation Batteries installationQuick Reference Guide Preparations Swivel belt clip Option Belt clip Third-party antennas may in- crease receiver performance Antenna About default setting Charging the batteryYour ﬁrst scanning Experience Adjusting squelch level Adjusting audio levelBasic operation Turning on the receiver Receive mode selection Setting frequencyMemory programming Selecting a memory channel Programming scan edges Writing a memory channel Programmed scan operationSelecting a scan edge channel B Selecting a scan edge channel a Cancelling scan Starting scan Select VFO modeStarting scan Selecting a scanning type Front, top and side panels Panel Description ULEFT Dial L-DIAL EPOWER KEY PowerIRIGHT Dial R-DIAL QDUALWATCH/CLEAR KEY Dualwatch MODE/SCAN KEY Mode Scan Or 10 MHz tuning steps pVOLUME/DIAL KEY 1 DIAL.SEL VFO/MHz KEY VFO MHz Inputs digit ‘5’ for frequency input, memory Push for 1 sec. to enter the set modeInputs digit ‘0’ for frequency input, memory Inputs digit ‘8’ for frequency input, memory @2STOP/PLAY ≈ WDUPLEX Indicators p QBATTERY IndicatorESIGNAL Squelch Indicators Function display TLOCK Indicator p RANL/NB Indicator pgsYAFC Indicator p USKIP Indicators p Battery installation Battery INSTALLATION/CHARGING Battery caution Battery chargingRegular charging Charging caution Rapid charging with the BC-156 CP-18A/E fuse replacement Mode selection Frequency and Channel SettingVFO mode Memory mode/PreSet*/TV*/Weather† channels Operating band selection Available frequency bands 2425 Setting a frequency Setting a tuning stepTuning step selection Using the dial Editting MHz to 1260.240 MHz Using the keypadFrequency can be directly set via numeral keys Lock function Receive mode selection When a signal is received Setting audio volumeBasic Operation Receiving Push and hold SQL to monitor the operating frequency Squelch level settingMonitor function RF gain Attenuator function Rotate R-DIALto select Duplex SettingDuplex operation NB/ANL function AFC function Select the sweep steps, if desired Band scope Single band operation Dial function assignment Operating bands table for dualwatch operation Main band selection Band exchange Lower band’s squelch adjustment Setting audio volume Squelch level setting Memory Channels Memory channel contentsGeneral description Memory channel programming Push MR S.MW for 1 sec. to set the channel into the bank Memory bank setting Rotate R-DIALto select the bank channel Memory bank selection Rotate R-DIALto select the desired character Programming memory/bank name Dication type from bank name or memory name Selecting memory/bank name IndicationAvailable characters Copying memory contents Memory clearing Push MR S.MW for 1 sec. to clear the contents Erasing/transferring bank contents Scan types Scan OperationFull Scan p FREQUENCY/MEMORY Skip Function p Full/band/programmed scan Select VFO mode with VFO MHzTo start the scan, release Mode Scan Scan edges programming Release Mode Scan to start the selected scan Select memory mode with MR S.MWMemory/bank/all bank scan To stop the scan, push Dualwatch During auto-memory write scanning Auto-memory write scanRecalling the stored frequencies Clearing the stored frequencies Skip channel/frequency setting Push Dualwatch to exit set mode Scan pause timerScan resume condition SET Scan resume timer About priority beep function Priority WatchPriority watch types Push Dualwatch to cancel the watch Push Dualwatch to exit set mode and start the watchPriority watch operation Select the desired memory channel While scanning memory/bank channels VFO scan watch qSelect memory mode0Push Dualwatch to cancel the watch and scan Push Dualwatch to stop the beeps and blinking man- ually Comfortable ReceivingTone/DTCS squelch operation Available Dtcs code list Tone squelch frequency/DTCS code settingPush 8 SET Available tone frequency list Dtcs polarity setting Push 4 T-SCANfor 1 sec. to start the tone scan Tone scan General SET ModeExpanded set mode ON/OFF General set mode items Set mode itemsExpanded set mode items Key-touch beep Priority watchBeep output level Display backlighting Noise blanker Power saveANL function AF ﬁlter Power and Lock No accessible key is available, exceptAM antenna selection FM antenna selection Default Auto power OFFDial speed acceleration Monitor key action Scan resume timer Scan pause timerScan stop beep Turns the scan stop beep function on and OFF Offset frequency Scope audio outputDuplex direction Sets the audio output function while scope operation Dtcs code Tone frequencyDtcs polarity Available subaudible tone frequencies Memory bank link LCD contrast can be adjusted through 15 levelsLCD contrast Turns weather alert function on and OFF CI-V transceive CI-V addressCI-V baud rate Other Functions RPush Dualwatch to exit set modeAntenna selection Selecting antenna Weather channel operation Turn the weather alert function OFF in set modeWeather channel selection Weather alert function Receiver shows following indications Cloning using a personal computerData cloning Cloning error Auto power-off function Recording a received audio Playing back recorded contentIC recorder Recording set mode Quality setting Playback speed setting Erasing recorded audio Automatic recordingREC Same time, but cannot erase each track independently Partial reset Data format Control CommandCommand table CI-V compatible transceiver Control Command TV channels Frequency TableS.A. channels Ccir channels New China channelsZealand Channels Italian channels Indonesian channelsTaiwan channels FOT channels Weather channelsunit MHz VHF marine channels HF CB Citizens Band channels Other communications in the USAChannels Murs channels Cable TV IRC Wireless MicrophonesGeneral aviation frequencies PMR446 channels unit MHz LPD Low Power Device channels Unit MHzOther communications- other countries UHF C.R.S Citizen Radio Service channels Troubleshooting Maintenance General Specifications Options Options For Microsoft Windows XP Driver Installation Driver Installation Windows starts installing the USB driver 0Repeat step e to y After the installation is completed, click Finish Found New Hardware Wizard will come up as below. Click Next For Microsoft Windows2After clicking Finish, the dialog appears as below Select Click Driver Installation For Microsoft Windows 98/98SE/Me Select Click COM port conﬁrmation Click the Device Manager IR20 Pocket Guide Release Mode Scan to start scan We Icom Inc. Japan Declaration Conformity Kamiminami, Hirano-ku, Osaka 547-0003, Japan #07 France