Invacare Ranger IISTANDARD F R O N T R I G G I N G S, Battery Tray, Height FIGURE, Bracket

FRONT RIGGINGS PROCEDURE 3

ADJUSTING FOOTBOARD MOUNTING BRACKET ANGLE - FWD MODELS ONLY (FIGURE 4).

NOTE: Angle availability is limited when the motors are in the forward-most position.

1.Remove the caplug cap.

2.Remove the front hex screw and caplug washer that secure the footboard mounting bracket and bushing to the wheelchair.

3.Repeat STEPS 1-2 for the opposite footboard mount- ing bracket.

4.Move the footboard mounting brackets to one (1) of three (3) positions.

NOTE: To ensure the existing hex screws tighten securely, apply Loctite 242 onto the threads.

5.Reinstall the two (2) hex screws and caplug washers through the two (2) footboard mounting brackets and bushings and into the wheelchair.

6.Torque the two (2) hex screws to 13-ft/lbs.

7.Reinstall the two (2) caplug caps.

Battery

Tray

3 Mounting
Positions	Bushing
Caplug	Footboard
Cap
	Mounting
	Bracket

Front Hex

ScrewFootboard

Pivot

Caplug

Assemblies

Washer

FIGURE 4 - ADJUSTING

REMOVABLE FOOTBOARD - ADJUSTING FOOTBOARD MOUNTING BRACKET ANGLE

Height (FIGURE 5)

1.Remove the removable footboard plate. Refer to

PREPARING REMOVABLE FOOTBOARD FOR WHEELCHAIR TRANSPORTATION in PROCE- DURE 3 of the Owner’s Manual.

2.Remove the caplug cap.

3.Removethemountingscrew,caplugwasher,flatwasher and nut that secures the two (2) large washers and sup- port tube to the height adjustment bracket and footboard bracket.RefertoDETAIL“A”.

4.Removethenut,flatwasherand thatsecurethethreaded arm on the height adjustment bracket to the footboard bracket. Refer to DETAIL “B”.

5.Perform one (1) of the following:

A.MWD WHEELCHAIRS - Move the height adjust- mentbrackettoone(1)ofseven(7)heightpositions.

B.FWDWHEELCHAIRS-Movetheheightadjustment bracket to one (1) of five (5) height positions.

6.Reinstalltheflatwasherandnutthatsecuresthethreaded arm on the height adjustment bracket to the footboard bracket. Refer to DETAIL “B”.

7.Reinstallmountingscrew,caplugwasher,flatwasherand nut that secures the two (2) large washers and support tube to the height adjustment bracket and footboard bracket.RefertoDETAIL“A”.

8.Reinstall the caplug caps.

9.Repeat STEPS 2-8 for the opposite footboard bracket.

10.Reinstalltheremovablefootboardplate.RefertoREMOV-

ING/INSTALLING THE REMOVABLE FOOTBOARD ONTO/FROM THE WHEELCHAIR in PROCEDURE 3 of the Owner’s Manual.

Nut

Height Adjustment

Bracket	Flat Washer
Caplug	Two (2) Large
	Washers
Washer

Caplug

Cap Mounting

Screw

	Footboard	Support Tube
DETAIL “A”	Bracket

DETAIL “B”
	Nut
Footboard	Flat Washer
Bracket
	Mounting
Height	Positions
Adjustment
Bracket
Threaded Arm

NOTE: MWDfootboardbracketshownforclarity.Footboard bracket on FWD models adjusts in the same manner.

FIGURE 5 - ADJUSTING FLIP-UP

REMOVABLE FOOTBOARD - HEIGHT

F R O N T

R

I

G G I N G S

17