INSTALLING REAR SHROUD AND REAR
STORAGE COMPARTMENT.4.
1. Positionthetwo(2)1/4-turnboltswiththetwo(2)mount- ing holes in the wheelchair frame.
2. Install rear storage compartment onto chair frame.
3. Turn two (2) 1/4-turn bolts that secure the rear storage compartment to the wheelchair frame CLOCKWISE.
4. Position rear shroud on the two (2) side shrouds and slide towards the front of the wheelchair until it stops.
5. Press down on the rear shroud until the two (2) clips secure the rear shroud to the two (2) side shrouds.
REMOVING SIDE SHROUDS.
1. Remove the front shroud from the wheelchair. Refer to REMOVING/INSTALLING FRONT SHROUD in this procedure of the manual.
SHROUDS
This Procedure Includes the Following:
Removing/Installing Shrouds
WARNING
After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - other- wise injury or damage may result.
REMOVING/INSTALLING SHROUDS
MWD Wheelchairs (FIGURE 1)
REMOVING FRONT SHROUD.
1. Turn the two (2) 1/4-turn bolts that secure front shroud to the two (2) side shrouds COUNTERCLOCKWISE.
2. Remove the front shroud from the wheelchair.
INSTALLING FRONT SHROUD.
1. Positionthetwo(2)1/4-turnboltswiththetwo(2)mount- ing holes in the side shrouds.
2. Install the front shroud onto the two (2) side shrouds.
3. Turn the two (2) 1/4-turn bolts that secure the front shroud to the two (2) side shrouds CLOCKWISE.
REMOVING REAR SHROUD AND REAR STORAGE COMPARTMENT.
NOTE: The rear storage compartment is available on wheelchairs NOT equipped with weight shift basic tilt only.
1. Lift up on rear shroud and remove from wheelchair.
2. Turn the two (2) 1/4-turn bolts that secure the rear stor- agecompartmenttothewheelchairframeCOUNTER-
CLOCKWISE.
3. Remove rear storage compartment from wheelchair.

PROCEDURE 10

2.Remove rear shroud and rear storage compartment (if equipped) from the wheelchair. Refer to REMOVING/ INSTALLINGREARSHROUDANDREARSTORAGE COMPARTMENT in this procedure of the manual.

3.Perform one (1) of the following:

A.INTEGRATED SLING SEAT MODELS - Fold the wheelchair. Refer to TRANSPORTING RANGER II MWD - INTEGRATED SLING SEATS in PRO- CEDURE 12 of this manual.

B.CAPTAIN'S SEAT MODELS - Remove the Captain's Seat from the wheelchair. Refer to RE- MOVING/INSTALLINGCAPTAIN'SSEATinPRO- CEDURE 5 of this manual.

C.WEIGHT SHIFT BASIC TILT MODELS - Pro- ceed to STEP 4.

4.Remove the phillips screws and washers that secure side shroud to wheelchair frame. Refer to FIGURE 1 for phillips screw and washer locations.

5.Remove the phillips bolt and locknut that secure the side shroud to the wheelchair frame. Refer to FIGURE 1 for phillips bolt and locknut location.

6.Repeat STEPS 4-5 for the opposite side of the wheel- chair, if necessary.

INSTALLING SIDE SHROUDS.

1.Position the side shroud on the wheelchair frame.

2.Line up the mounting holes in the side shroud with the mounting holes in the wheelchair frame.

CAUTION

DO NOT overtighten the phillips screws and phillips bolt that secure the side shroud to the wheelchair frame - otherwise damage to the side shroud can occur.

3.Install the phillips bolt and locknut that secure the side shroud to the wheelchair frame and tighten securely. DO NOT OVERTIGHTEN. Refer to FIGURE 1 for phillips bolt and locknut location.

Install the phillips screws and washers that secure the side shroud to the wheelchair frame and tighten se- curely. DO NOT OVERTIGHTEN. Refer to FIGURE 1 for phillips screw and washer locations.

5.Repeat STEPS 1-4 for the opposite side of the wheel- chair, if necessary.

6.Perform one (1) of the following:

A.INTEGRATED SLING SEAT MODELS - Unfold the wheelchair. Refer to TRANSPORTING RANGERIIMWD-INTEGRATEDSLINGSEATS in PROCEDURE 12 of this manual.

B.CAPTAIN'S SEAT MODELS - Reinstall the Captain's Seat onto the wheelchair. Refer to RE- MOVING/INSTALLINGCAPTAIN'SSEATinPRO- CEDURE 5 of this manual.

S H R O U D S

33

Page 33
Image 33
Invacare Ranger IISTANDARD R O U D S, Weight Shift Basic Tilt Models Pro- ceed to Step, Installing Side Shrouds