Error Messages

 

Error Message

 

 

Error Description

Remedy

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Communication error with the

Turn the power switch off and turn it on again.

 

 

 

E : 00

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RCS unit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Initializing error

Turn the power switch off and turn it on again.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Needle bar switching error

Turn the power switch off and turn it on again.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Needle bar stop position error

Press the ENTER button to reset the machine.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Driving motor stops due to an

After 15 seconds, the LCD screen will show the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

overload.

Ready to Sew mode display. Remove jamming

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

threads or other cause of overloading.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Needle thread broke or ran

Press the MODE key to return to the Ready to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

out.

Sew mode and re-thread the needle.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Needle bar setting error

Press the MODE button to return to the Ready to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sew mode then set the needle bar number.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Auto thread cutting error

Turn the power switch off and turn it on again.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Opening tension disks while

Pull the tension release lever to close the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

stitching

tension disks. The LCD screen will show the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ready to Sew mode display.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Upper shaft stop position

Turn the power switch off and turn it on again.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

error

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Audible Signals

 

 

 

 

 

Audible signal

The buzzer sounds when:

 

 

 

 

 

 

 

pip

 

Normal operation

 

 

 

 

 

 

 

pip-pip-pip-pip

 

Invalid operation or malfunction

 

 

 

 

 

 

 

pip-pip

 

Thread color change

 

 

 

 

 

 

 

pip-peep pip-peep

 

Embroidery completed

 

 

 

 

 

 

 

peep

 

Malfunction

 

 

 

 

 

 

 

 

 

 

 

 

 

80

Page 83
Image 83
Janome MB-4 manual Error Messages, Audible Signals, Audible signal Buzzer sounds when