|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 6. Press the VIDEO SELECT button | 6. Press the VIDEO SELECT button |
| |||||||||||||||||||||||||||||||||||||||||||||
| VIDEO IN 1 and VIDEO 2 videos will switch every | VIDEO IN 1 and VIDEO 2 videos will switch every |
| |||||||||||||||||||||||||||||||||||||||||||||
| time the button is pressed. | time the button is pressed. | ||||||||||||||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7. Press the STOP button | 7. Press the STOP button | ||||
|
|
|
|
|
|
Connection will be discon- |
|
|
| Connection will be discon- |
nected and the number dis- |
|
|
| nected and the number dis- |
|
|
| ||
played will be cleared. | played will be cleared. | |||
■Multicast send/receive signals ( See page 34)
<Camera side> | <Monitoring side> |
1. Press the “START” button in Multicast of the NETWORK SETUP screen.
| 2. | Enter the number that is registered for | |||
|
|
|
| multicast. | |
|
|
|
|
|
|
3. | 3. | Press the PLAY button. | |||
| The ENCODE lamp and DECODE lamp will light. | The entered number and the DECODE lamp will | |||
|
|
|
| light. | |
Memo
When unicast communication is stopped in camera side, the number display on the camera side is off even if the unit is sending multicast stream and some monitor side is receiving it.
When configuring remote monitoring system, set same frame rate to camera mode unit and monitor mode unit. Set bitrates within same color on the select bar to all units.
Settings are performed in the ENCODE PARAMETERS screen for both camera mode unit and monitor mode unit (page 32). Monitor mode can set encode parameters for each destination camera side unit in the TELEPHONE BOOK screen.(page 34) When settings in camera side and monitor side are different, connection may take for a few seconds because settings are changed during connection. JPEG recording will also be unavailable during this time.
Same settings are recommended for units used for automatic alarm connection. (page 38).
Operations
45